Jacuzzi installation technology indoors and outdoors: step by step instructions

How is a Jacuzzi set up?

Jacuzzi device: 1 - hydromassage jets; 2 - pump; 3 - compressor; 4 - electronic control system; 5 - overflow device

Unlike a conventional bathtub, the jacuzzi is equipped with a hydromassage system, which consists of a pump, a water intake and hydromassage jets. As a rule, the pump is supplied complete with a hot tub.

Water intake (bottom) and jets (top) whirlpool

With the help of this special pump, water from the bathroom is pumped out through the water inlet, passes through a network of hoses and is supplied under pressure to the hydromassage nozzles. In the center of the nozzle is a nozzle through which water is supplied.

Whirlpool pump

Hot tub pump

The design of the nozzle is designed in such a way that the outlet water jet mixes with the air entering the nozzle, thereby increasing the efficiency of the jet. There are several types of nozzles: some of them are designed for back massage, others - for lumbar massage.

Water is pumped through the hoses and enters the nozzles

Some jacuzzi models are equipped with an air compressor and can operate in "turbo" mode. The aero compressor pumps a significant amount of air into the hydromassage system, which is released through the hydromassage nozzles, increasing the pressure of the water jet.

Air compressor for jacuzzi

And some jacuzzis boast an air massage system. During aeromassage, the air pumped by the aerocompressor exits through special aeromassage nozzles located at the bottom of the bath. They give air-bubble jets that increase the overall muscle tone. There are also varieties of jacuzzis with only an aeromassage system, without hydromassage.

Jacuzzi with air massage system

In addition, there is a jacuzzi can have a lighting system that allows you to make the process of taking a bath even more enjoyable. And the coolest jacuzzi models are equipped with chromotherapy systems (light treatment). Such whirlpools allow not only to relax and get a pleasant massage, but also to enjoy healing illumination, and if you turn on your favorite music, then color music. Just do not take appliances powered by the mains with you into the bath.

Illuminated jacuzzi (on board there is a regulator and buttons for turning on the hydromassage)

Along with all the listed features, some Jacuzzi models are equipped with additional functions of ozone or aromatherapy.

All these systems are controlled by buttons, regulators and taps-switches. Buttons that turn on and off the necessary equipment, as a rule, are made pneumatic, which ensures electrical safety.

Pneumatic Buttons for Whirlpool Control System

Regulators allow you to change the strength of the water or air jet, the volume of air supplied, etc. Using the switch valve, you can direct the air flow from the pump to one or another group of nozzles to increase the effect on different parts of the body.

Jacuzzi spout

Faucets, spouts, and faucets are typically wall-mounted in hot tubs, rather than wall-mounted as they are in regular bathtubs. The overflow system in the hot tub is usually semi-automatic. There is a special valve in the drain system, which is opened using the overflow handle. As a rule, such a handle is located on the overflow hole. If the water level exceeds a certain level, the water is drained through the overflow hole located under this handle. Some hot tubs have a drain pump that circulates the water in the tub.

Whirlpool power is from 800W, hydromassage pump power is from 800W to 1500W, and air compressor power is from 400W to 800W. Together, together with the drainage pump, the power of some systems can reach 30 kW.

Care

In order for a hot tub to serve you for a long time, you need to follow certain rules.

How to wash an acrylic bath? For its cleaning, all abrasive cleaners, as well as products containing acid, alkali, chlorine and other aggressive chemical elements are strictly prohibited.

Bathing pets and putting hard objects into it, especially with sharp edges, is also not necessary. All of these can damage the surface.

Only soft sponges or cloths and gel-like cleaners are used for maintenance. To remove water deposits, you can use folk remedies. For example, you can dampen a sponge with a 3% solution of acetic acid or citric acid.

If you still have small scratches on the surface of your tub, you can sand them down with the finest grit sandpaper (M9800-1200), and then apply car polish paste to restore shine.

To prevent the appearance of rust stains, after each use, the bath must be wiped dry with a clean, dry cloth. It is better if it is linen, woolen fabrics are not recommended.

Once every one or two months, the hot tub needs to be disinfected. To do this, add 1 cup of disinfectant, which can be purchased at bath shops, to a filled bathtub, and turn on the pump for 2 minutes. This time is sufficient to fill all zones of the system with water. Then the hydromassage must be turned off, and the water in the jacuzzi must be drained after 20 minutes. During this time, the piping system will be cleared of microorganisms. After a repeated cycle of pouring and draining water into the bowl, the bathroom can be used.

If you have "hard" water, then the whirlpool bath system needs to be cleaned at least twice a year. The procedure is as follows:

• fill the bowl with water at a temperature of +40 ° C, pour detergent into it (approximately 2 grams of detergent per liter of water) and turn on the pump for a short time;
• turn off the pump, drain the water from the bowl;
• fill the bowl this time with cold water and turn on the pumping equipment for 2 minutes;
• turn off the pump, drain the water, and wash the jacuzzi as usual.

It is not recommended to carry out the cleaning and disinfection procedure together, since mixing the two liquids can lead to the failure of the hydromassage equipment.

As you can see, there is nothing complicated. Call a specialist or install the bath yourself - it's up to you. I hope this article will help you make the right choice.

Compressor installation

The set of equipment that will need to be installed on a homemade jacuzzi bath depends on what type of massage it is designed for:

• air massage: it is enough to install only the compressor;
• air massage and hydromassage (water jet supply): in addition to the compressor, you will need a pump.

When choosing the second option, it is necessary to provide a hole in the wall of the bowl through which the pump will take water to be supplied to the massage circuit.

The equipment does not give the bath aesthetics, so it should be installed hidden. To do this, a recess is made in the floor or a niche in the wall, which will be closed with a lid. The switches connected to the devices must be installed in some place convenient for the bather - on the bath itself or nearby on the wall.

Do not want to suffer with the installation of a jacuzzi? Buy a hot tub mat that doesn't require special installation but performs similar functions.

Types of whirlpool baths, as well as their sizes and prices, are listed in the following article.

How to install a hot tub. Step-by-step instruction

Photo 3. Device bath with hydromassage.

Step 1. Bring the bath and put it on its legs in the place provided for it. Set the height to level.Alignment is carried out using the adjusting bolts on the legs. There are ways to install on the mounting frame. For better drainage and to avoid stagnation of water in the bowl, make a slight slope towards the drain.

Step 2. Connecting to the sewer. We connect the drain system according to the manufacturer's instructions. When installing, make the drain in the bathroom 10 cm higher than the main drain. If this is not done, the speed of draining water from the hot tub will be slow.

Step 3. Connecting the jacuzzi to the central water supply. All work is carried out in the same way as for a conventional bath without hydromassage installations. Connect the flexible hose from the hot tub to the plumbing system. Remember to seal all joints. To do this, use fastum tape, plumbing or linen tow. New gaskets are also installed, elastic, without burrs. After connection, check the tightness. To do this, turn the valve. There should be no leaks, hissing, gurgling or other sounds in the hose. At the junction of the hose with the sewer, attach it to the wall.

Step 4. Trial run of the bath. Draw water into the bowl, about 10-15 cm. Inspect the equipment for leaks. Drain the water. Make another set of water above the permitted level. During the overflow, make sure there are no leaks and the safe descent of water.

Photo 4. The process of installing a jacuzzi.

Step 5. Sealing the junction of the bathtub with the wall. In order to exclude the formation of mold and dampness, it is necessary to ensure a snug fit of the equipment to the wall, and we coat all joints with sealant.

Step 5. Install removable panels. They are needed for beauty and access to communications.

Step 6. Connecting the whirlpool bath to the mains. This is a critical stage of installation. Water is a good conductor of electricity. The performance of these works requires strict observance of electrical safety rules. To perform the work, you can invite a professional electrician, he knows how to connect the hot tub to electricity.

Connecting the jacuzzi to the mains

Knowing the steps and nuances of connecting a hot tub to the mains will help you control the work of an electrician or do it yourself. All electrical work is carried out when the network is de-energized. To do this, turn off the switch on the panel that is responsible for the bathroom. You can turn off the general switch in the apartment. The safe use of the hot tub is only possible when connected with a three-wire cable to a grounded socket. The bath socket is installed outdoors. The distance is approximately - 07-1 meter, so that it could not be reached. Use a European style socket with neutral, live, and grounding prong.

Photo 5. Supplying electricity to the bath.

Connect the socket to the electrical panel. To do this, you need to use a machine and a protective shutdown device. Install a separate RCD for this outlet. You can also connect the jacuzzi bath through the switch. It comes with her. It is also located at a distance of 0.7-1 meters. So that it was impossible to reach him to a person taking a bath.

The next step is to connect the electrical wires of the cable from the mains to the hot tub wires. Make sure that the zero of the cable is connected to the neutral wire from the bath, and the phase, respectively, to the phase, the ground to the ground. To avoid confusion, use the accepted in the world of color designation.A white or red wire goes to the phase, blue is responsible for zero, and yellow-green is ground.

The nuances of installing a hot tub

A whirlpool bath is heavier than a conventional one not only because of its large size: the weight is increased by additional equipment (pump, nozzles, piping system, etc.). Therefore, horizontal and height adjustment with screw feet is not applicable. The jacuzzi is installed on a special frame made of pipes.

To install a hot tub, a frame made of metal pipes is used.

This requires a special approach to the preparation of the floor: it is carefully leveled with a screed and a self-leveling mixture.

For the operation of this plumbing fixture, it is necessary to connect to three communications: to water supply, sewerage and electricity. Water pressure in pipes and service equipment should not exceed 5 atmospheres. To protect the system, a pressure reducer should be installed, since during periodic tests the water pressure may exceed the rated pressure by two times. Protection against power surges should also be provided: at the entrance to the house (after the meter), you need to install a cut-off relay or a stabilizer of the necessary power. The requirements for installing a drain sewer are the same as those that must be observed in the case of a conventional bathroom: the drain hole is located above the bed of the system, and the connection is made with a rigid pipe.

The junction of the whirlpool siphon with the sewer must be accessible for maintenance: pipes periodically become clogged and must be cleaned. The same requirements apply to the junction of the bath equipment with the water pipe: if necessary, dismantling should be carried out without difficulty.So that the nozzle holes are not “clogged” with deposits of metal salts and other impurities, it is required to install coarse and fine filters.

The hydromassage effect is achieved with the help of jets of water supplied under pressure through nozzles.

Features of the operation of the jacuzzi

First, water is drawn into the bowl, and only then they are launched

It is important that all nozzles are located in the water, otherwise the pump may overheat, causing it to leak or fail. After starting, the intensity of the jet is usually adjusted, the nozzles of the nozzles are adjusted

If the jacuzzi is equipped with a backlight, then it must not be turned on if the bath is not filled with water, otherwise the lamp may overheat and the body will be deformed. Water acts as a coolant for the lamps

When operating a jacuzzi, it is allowed to use aromatic substances, essences that do not form foam. Permissible water temperature - up to +50 degrees.

Recommendations for the care and elimination of scratches

Let's move on to the section: tips for care and repair of scratches.

Alkali, acid and other aggressive components are unacceptable; it is unacceptable to clean the acrylic bath with abrasive substances, products containing chlorine. Soft fabrics and sponges, you need to use gel-like cleaning chemicals.

You can get rid of hard-to-reach contaminants in nozzles using the following method.

• To mix the water with the composition, start the pump for 10-20 seconds.
• Water is poured into the bowl to the top, the temperature of which is at least 20 degrees.
• 1-1.5 acetic (7%) or citric acid is added to the water.
• The solution is left for 12 hours, after which it is drained.
• After that, the water is drained, then the jacuzzi is filled with water, the pump is started to rinse the bath from the previous composition.

The procedure should be carried out 1-2 times a year. After that, a car polishing paste is applied, small scratches are cleaned with fine-grained sandpaper. In the future, after each bath, the bath is wiped dry with a dry, clean linen cloth to prevent the formation of rust.

If the jacuzzi does not have a built-in automatic disinfection system, then every month it must be carried out on its own. To save water, it is allowed to use water in the future after the hydromassage procedure. To do this, use any disinfectants.

_

Month - a unit of time calculation according to the solar calendar, equal to one twelfth of a year; period of 30 days.

To disinfect the jacuzzi, you need to fill the bathtub with water so that its level covers the top row of nozzles. Based on the manufacturer's recommendations, after that, the pump is started for 1-2 minutes, wait 10-15 minutes, then the water is drained, a certain amount is poured into the bathtub disinfectant solution.

To clean the bowl from the remnants of the product, then you need to draw water again. We also recommend that you look at the detailed instructions for the care of the hot tub.

Installation Recommendations

In order for your outdoor hot tub to last as long as possible, certain requirements must be met when installing it.

• Outdoor hot tubs need to be sheathed with a special material that will differ in the presence of thermal insulation properties. If the temperature outside drops below zero, the water in the system may simply freeze, which is unacceptable.To avoid serious damage to the fluid purification system and its normal circulation, it is best to use a heater, for example, polyurethane.
• The device should be placed on a flat surface specially prepared for this purpose. It is best to use a prepared concreted area for this. In this case, you can easily avoid the possibility of skew or severe damage to your new hot tub.
• If you are going to operate your hot tub not very often, it is still better to drain the water for the winter period. Pools that have increased frost resistance, in principle, will be able to withstand the weight of a well-frozen liquid and have a significant margin of safety up to about 10 years, but it is better not to subject them to unnecessary stress.

In outdoor types of hot tubs, external cooled air is not used, most often the right amount of air is taken from the space that is under the bowl of the device - a truly warm temperature prevails there. Because of this, the most comfortable types of massage are carried out in the cool season.

Most often, these products are produced for Canadian users, because the climatic conditions of this country are far from ideal. And this means that products of this kind are perfect for our climate zone.

The following video provides an overview of the Intex PureSpa Bubble Therapy+Hard Water System.

Hydromassage mechanism

In short and in a nutshell, the essence of hydromassage boils down to the fact that air is supplied to the filled bath by a special compressor, which is why bubbling bubbles appear.Thus, in contact with the skin, they interact with the nerve endings, imparting a pleasant effect to the entire body.

In order for this pleasure to last as long as possible, the bath must function normally and be properly connected to all the systems that make up the mechanism: sewer, electrical, water and air. A breakdown of one can lead to another, therefore, with a hydromassage, it should be left to the masters if the owner has no skills. Independently, you can only carry out work on the acceptance of this unit by the premises. There are also many difficulties, and all installation processes will have to be carried out carefully.

Hot tub water connection

The technical parameters of the bath are designed for its operation in a water supply system with a pressure of 4-5 atm. However, for greater reliability, it is recommended to additionally install a pressure reducer.

Jacuzzi nozzles are very sensitive to the quality of the incoming water, therefore, a prerequisite for connection is the installation of coarse and fine filters. This will protect the expensive system from damage. After all, rarely any citizen of our country can boast of the quality of tap water.

It is better to bring pipes as close as possible to water consuming devices. At the same time, it should be taken into account that they do not block access to the joints of the pipes and the bath

This is very important if you need to audit or repair.

Installation of the faucet and connection to the water supply in the jacuzzi does not differ from their installation and connection in conventional bathtubs. The only difference is that the faucets at the hot tubs are installed directly on the baths themselves, and not on the walls, as in simple ones.The "drain-overflow" system on such baths is usually made semi-automatic: the drain valve is opened using a handle located on the overflow hole.

When the water reaches the critical level, it begins to overflow through the drain hole, which is located below the handle. The connection itself is carried out using a flexible water supply. The length is taken taking into account the possible movement of the bath relative to the wall at a distance of at least half a meter.

Related article: Do-it-yourself curtains for the kitchen: patterns and subtleties of tailoring

At the outlet of the water supply pipes, mixers with a thread with a diameter of 1/2 ″ are placed

When performing work, it is important to monitor the tightness of the joints, if necessary, use gaskets

Jacuzzi for a bathroom in an ordinary apartment

How to make a jacuzzi with your own hands in an apartment of a multi-storey building? This is of interest to many owners of urban housing. We offer a simple solution for a bubble bath. You will need an air compressor with a capacity of 10 l / min or more, as well as a flexible hose. It is better that it be made of transparent material. It is necessary to make holes in it with a diameter of about 1.5 mm every 100 mm. Through these holes, the air pumped by the compressor, which is installed under the bath, will exit.

The air duct is connected in the form of a closed system. It is not as easy to realize a dream on your own as it seems: you need to have the skills not only of a builder and plumber, but also of hydraulics and an electrician.

A detailed diagram of a hydromassage bath will help you design it in your apartment.

Scheme of a bath with a hydromassageThe experts we recommend you contact will help you overcome difficulties.

Design and principle of operation

To install a jacuzzi with your own hands, it is important to know the design features and principles of operation of hydromassage plumbing. A typical set of technical equipment for a hot tub includes:

A typical set of technical equipment for a hot tub includes:

• compressor (intake);
• pump;
• control systems of electronic or pneumatic type;
• nozzles;
• pipe systems.

With the help of a pump, water enters the hydromassage system, enters the compressor, where water and air are mixed. The jet enters the nozzles, after which it is fed under pressure into the bath.

The figure shows the location of the important elements of the whirlpool - compressor, pump, jets, built-in display and control system

The type of massage depends on the type of nozzles. Sewer pipes are connected to the pipe system.

As additional elements in some models there are:

• a drainage system that ensures uninterrupted water circulation;
• audio or video installation;
• built-in modules for chromo-, aroma- and ozone therapy.

In the Jacuzzi sets, you can find several additional nozzles, which, if desired, are easy to install. In this case, a more powerful pump will be required, which should be purchased separately. For a large bath volume, a powerful pump is required.

The effectiveness of the jacuzzi is affected by the number and configuration of nozzles, as well as the location of the hydromassage elements in the bath.

A more detailed device for a hot tub and a variety of equipment is covered in another article on our website.

Examination

After all the work is done, especially if you did not do the installation yourself, you need to check the quality of the connection.

First of all, pay attention to the filters and pressure reducer. Filters must be multi-stage

Compressors and pumps should be freely accessible for easy dismantling in the event of a breakdown. All wiring, if placed on the wall, should be hidden in a box. Check the installation of the RCD and the quality of the wire connection: phase, zero and ground. Fill the jacuzzi with water and check if all the water goes down the drain.

If there are no complaints about the installation, you can start taking hot tubs with peace of mind.

Preparatory stage

When planning to install a jacuzzi in your home, be prepared for the fact that it will take a lot of effort and time to implement the idea.

The design of the jacuzzi often has impressive dimensions, therefore, in most cases, its installation requires redevelopment of the bathroom

The hot tub is quite heavy, and when filled, depending on the dimensions of the container, it can weigh up to one and a half tons. The load on the floor, created by each square meter of construction, can reach 220 kg.

This should be taken into account when planning the redevelopment of rooms, for example, by combining part of the corridor with a bathroom. In order for the floors to withstand the load created by the filled bathroom, it is necessary to provide for the strengthening of the floors.

The main 9 elements of the hot tub are collected in 3 groups:

• The external group includes pneumatic activation of aero and hydromassage, as well as adjustment of the power of the water-air jet.
• The propulsion system consists of an air compressor and a water pump.
• The piping system includes inlet and outlet g/m pipelines, as well as air tubes of the a/m system.

Before buying a jacuzzi, you need to take a number of measurements in the bathroom. The dimensions of the selected model should be such that after its installation there is still free space up to 50 cm. This will make it possible to move the structure away from the wall for preventive measures and repair work. Tightly embedding a jacuzzi is not recommended.

A hot tub is a rather complex structure, equipped with pumps, a heater and various nozzles, and therefore requires a thorough approach when connecting

To power the unit, it is necessary to allocate a large amount of energy, since the total power of electrical mechanisms can exceed 3 kW. And the wiring of apartment buildings is not designed for it.

Electrical wiring at 220 V with a frequency within 50 Hz must be brought into the room even before the start of work, hiding it in the wall of the room and performing waterproofing. It is better to connect a hydromassage bath not through an outlet, but directly out from the input distribution device.

In a room with high humidity, where it is planned to install a bath with a hydromassage, ventilation outlets should be provided.

At the time of the start of installation work, the repair in the room must be completed

Pay special attention to the following points:

• Walls and floors within the height of the whirlpool, which can reach 1-1.3 meters, must be thoroughly waterproofed.
• To exclude a possible overflow of water into the corridor and living rooms, the threshold from the bath is made 3-5 cm high.
• The towel dryer is placed away from the hot tub.

If the repair is not completed, individual auxiliary parts of the system may be damaged during installation and operation.When changing the installation location of the bath, care should be taken to purchase the necessary components for the "building up" of water and sewer pipes.

Additional aspects that are important to consider when connecting a hot tub:

• The pressure in the water supply system should be 4-5 atmospheres. Compliance with this condition will ensure the possibility of adjusting the water supply.
• Installation of a filtration system. This is due to the fact that running water is rarely particularly clean. It always contains various kinds of impurities that clog the nozzles, reducing their service life.
• The drain should be 10 cm below the drain level. If this condition is not met, there is a high probability of stagnation in the pipes.

One of the prerequisites for installing a whirlpool bath is to provide easy access to the mounted system.

The ideal option for the location of the jacuzzi is when the sides of the structure do not adjoin any of the walls of the room, and the communications supplied to it are hidden under the floor

Some craftsmen solve this problem by placing the structure closer to the middle of the wall. In the absence of the possibility of placing the bath in the center of the wall, it is installed in a corner in such a way as to provide maximum access from both sides.

A pre-drawn communication scheme will help facilitate the task of installing the structure. It should indicate:

• water pipes;
• sewer pipes;
• wiring.

In order to ensure maximum safety during the operation of the system, take care to install a residual current device and arrange grounding.

Tips from experienced plumbers

No matter how reliable the factory assembly of the shower panel may seem, the nuts of the connected pipes, hoses and pipes should be checked and tightened with a wrench. After installing the shower in place, all connecting nodes will be invisible.

It is not clear what will happen behind the blind panels there. It's not worth bringing the matter to the flood. Tightness and once again tightness. No pipe connection should leak a week or a month after the connection and installation of the shower is completed.

If the drain hole of the shower cabin is too far from the sewer inlet, then you will need to install a waste pump. It will not be possible to organize gravity here through pipes. Such a unit works silently, and the size is just right for placement under a pallet.

A bathroom with a shower cabin installed must have good ventilation, this is especially important if there is a “steam bath” function

All piping should be at a slight slope. Gravity is needed for both sewerage and water supply. Sewer pipes are laid with an inclination to the riser, and water pipes - from it to the shower cabin, so that when the water is blocked, it completely flows out of the system.

In overly budget models, the drain can be made of silumin alloy. This drain will last a maximum of two to three years. It’s better to spend money right away and change it to an analogue made of stainless steel, which also comes with a normal siphon made of high-quality plastic.

Water pipes leading to the shower cabin should be equipped with ball shut-off valves and dirt traps. Water in centralized systems is not always perfectly clean. If the holes of the watering can are still not clogged with grains of sand, then the nozzles will definitely stop working.Filters with valves can be placed directly at the riser or at the ends of the inlets at the booth.

Preparatory activities

Here is a list of the tools you can't install a hot tub without:

• roulette;
  wrench;
  square;
  gun (required for applying glue or sealant);
  pencil or marker;
  screwdriver;
  knife with a retractable blade;
  pliers;
  tester or screwdriver with indicator.

Necessary tools for work

Most of the necessary tools are easy to find, so there will be no problems. Even before installation, you need to properly prepare the room.

1. Read the installation requirements - they are listed above and are indicated in the manufacturer's instructions.
   Measure the room, decide where exactly the jacuzzi will be installed.

Before purchasing and installing a jacuzzi, be sure to familiarize yourself with its dimensions and compare them with the area of ​​\u200b\u200bthe room where the bathtub will be installed.

Take care of a high door threshold, thanks to which water will not enter other rooms in case of flooding.

High threshold in the bathroom

The heated towel rail should be located as far as possible from the location of the hot tub, move it if necessary.
It is important that there is at least 50-60 cm from the product to sockets and electrical appliances. If necessary, take them away to comply with electrical safety standards

On the example of this scheme, you can see the restrictions on the installation of sockets and electrical appliances near the bathroom or jacuzzi. In zones 0 and 1, their installation is not allowed under any circumstances. In area 2 it is undesirable. Zone 3 allows the installation of sockets, but only with protection against moisture ingress

A podium under the jacuzzi, if it is, also build in advance.
The water supply should run closer to the installation site, take care to arrange shut-off valves so that during maintenance / repair of the hot tub, you do not have to completely turn off cold and hot water.
Coarse and fine filters should be placed on the pipes that go to the installation site of the bath. If the water is of poor quality, the hot tub nozzles will quickly fail, and repairing them is much more expensive than periodically changing the cleaning elements of the filters.

Coarse filter

With unstable pressure, pressure reducers are installed on the lines of cold and hot water supply.
Finishing work must be completed before the Jacuzzi is installed.

It is important to finish finishing work in advance

Characteristics of the hot tub room

Initially, before buying a jacuzzi, it is necessary to analyze the parameters of the restroom and, based on this, give preference in favor of the model that is most suitable for a particular bathroom.

Consider the basic requirements that are important to consider in the process of choosing and installing a product. 1. The shape of the object should correspond to the place of installation - a round jacuzzi is installed in the center of the room, an oval jacuzzi is installed along the wall, and a corner jacuzzi is designed for the corner of the room

The shape of the object should correspond to the place of installation - a round jacuzzi is installed in the center of the room, an oval jacuzzi is placed along the wall, and a corner jacuzzi is designed for the corner of the room

1. The shape of the object should correspond to the place of installation - a round jacuzzi is installed in the center of the room, an oval one is along the wall, and a corner jacuzzi is designed for the corner of the room.

2. It is unacceptable to carry out the installation of the product "tightly", since the hot tub must be freely "located" in the room.

3.Ensure the strength of the supporting structures. This need is due to the fact that when filling the bath with water, there is a large load on the supports.

4. Provide for at least one ventilation outlet.

5. Ensure good vapor and waterproofing of the ceiling under the appliance.

6. Locate the water dispenser as close to the water supply as possible.

Hydromassage bath

For efficient operation of the device, the pressure in the system must correspond to 4-5 atm. To avoid the occurrence of drops and water hammer, as a rule, a pressure reducer is installed.

Due to the large weight of the jacuzzi, its height is not adjusted.

The device is mounted exclusively in a horizontal position on a metal frame, which is previously fixed to the floor. That is why at the preparatory stage it is necessary to carefully level the floor.

For efficient and reliable operation of the hot tub equipment, special attention should be paid to the quality of the water consumed. To minimize the likelihood of nozzle clogging, coarse and fine filters are installed. Connecting a whirlpool bath is recommended in rooms that strictly comply with the following requirements:

Connecting a whirlpool bath is recommended in rooms that strictly comply with the following requirements:

• finishing work in the room must be completed;
• easy access to the units and components of the bath should be provided so that preventive warranty service and repairs can be carried out without undue difficulties;
• the room must be supplied with power lines with the required parameters and sockets with grounding must be installed;
• Sewerage and plumbing are required.

Before starting work, you should familiarize yourself with the general scheme of the device device

Operating rules

1. Install pre-filters on the plumbing in front of the hot tub so that the holes for the jets of water (hydromassage) do not get clogged with sand.
2. To prevent the pump and compressor from failing due to overheating, limit massage sessions to 30 minutes and turn off the equipment for at least 10 minutes after each session.

If there is a hydromassage function, periodically pump a disinfectant solution through the pump and massage circuit.

To do this, you need to fill the bath and dissolve a special composition for disinfection in water (you can buy it in stores like "everything for baths"), and then let the equipment work for 10 minutes.