How to choose or make a washbasin for a heated cottage

How to build a garden washbasin from a canister

A more solid and practical design is a plastic canister washbasin. You can use any other metal container (bucket, pan, basin) as a storage tank. In addition, you will need a water supply iron or plastic faucet.

It takes a minimum of time to make it.

The manufacturing technology of this model with an iron crane is as follows:

1. On the side wall of the tank in the lower part (at a distance of 1.5–2 cm from the bottom), drill a hole for tapping the required diameter.
2. Insert the fitting (after unscrewing it and removing the clamping nut with one sealing rubber) so that the thread comes out. For strength, install a metal plate, then put on the previously removed seal and tighten the nut with a wrench. Additionally, you can coat all layers with sealant.
3. Now screw the coupling to the fitting and tighten it carefully.
4. Connect the tubing.

If the faucet is plastic, then it is recommended to use hot glue to fix it. And in the case when both components are made of iron, then welding is acceptable.

To start fully using the washstand, you should fix it in the right place - on the wall, on a tree, on a special stand.

To ensure the drainage of flowing water from below, it is desirable to equip a drain into the sewer, a cesspool, or simply put a bucket. If the soil absorbs moisture well, then expanded clay, gravel or crushed stone can be poured from below.

Do-it-yourself washbasin for a summer house manufacturing principle

Both a washbasin with a water heater for summer cottages and a washbasin for summer cottages without heating water are made according to the same principle. As you understand, the difference between them lies in the presence or absence of a heating element. Both products consist of three parts, the manufacture of which will have to be taken care of in the process of resolving the issue, how to make a washbasin for a summer residence on your own?

Sink. Let's start with it, since, in general, it is not necessary to make it - it would be more correct to say that it is almost impossible to make it at home. It is better to purchase a sink or use an old one - you can use any that is available

Even a kitchen sink will do - mortise or overhead, it doesn’t matter.Just based on its type, you will have to make a cabinet for it.

Cabinet - in a simplified version, it can be called a small table or a large stool

The only condition for the manufacture of such a base for a sink is that at the same time it also serves as the basis for installing a storage tank. In most cases, the back of such a cabinet rises up to a height of up to 800mm from the level of the sink - in fact, it is a panel, apron or work wall. Whoever likes to call her more, call her that - the tank is attached behind her. If the appearance of the product is not particularly interesting, then you can attach it to the front - in this case, its installation will be a little easier. Such a cabinet can be made from a fairly wide range of materials - in most cases, either natural wood in all its diversity is used for it, or its sheet composite in the form of chipboard, OSB, plywood, and so on. In general, what is at hand can be worked with - by and large, the cabinet can even be assembled from drywall or laid out with bricks.

Water tank. Without it, neither a simple nor an electric washbasin for a summer residence can work. The ideal solution for a country washbasin would be a rectangular container - it is easiest to place it on a cabinet. In general, any tank is suitable - both metal and plastic. The main thing is that you understand how it will be mounted on the cabinet. By the way, mounting the container on the pedestal is by no means the only solution to this issue - by and large, the container (of a rather large volume) can also be installed in the attic of the house. With this approach to business, you can even make a full-fledged plumbing in the house. But back to the manufacture of the container.Everything is simple here - the finished tank will need to be equipped with at least one tap outlet and, as a maximum, make another threaded hole with a diameter of one and a half inches for mounting a heating element into it. The necessary pipes with internal threads will have to be welded into the container in the right places.

And the rest, as they say, is a matter of technology, and assembling a washbasin is not a difficult task. First you need to fix the sink on the cabinet, then install the tank, after screwing the tap into it and, if necessary, a heating element that can be freely purchased on the market (such elements are used in storage water heating tanks). And, of course, it will be necessary to correctly connect such a heater to the power supply network - it is better to ground it so that no one is accidentally shocked.

In principle, that's all - as mentioned above, a washbasin for a summer residence is a fairly simple product to make on your own

The only thing I would like to add is to pay some attention to aesthetic characteristics - they completely depend on your approach to business and your vision of this product. You should not think that it is impossible to collect something worthwhile from old and unnecessary things - here it is just the opposite. The use of old things and objects is a guarantee of uniqueness, I'm not afraid to say again that it all depends on your diligence

Do not be too lazy to update the same old boards (for example, using a grinder and a special circle) and get a pretty decent and pretty product

The use of old things and objects is a guarantee of uniqueness, I'm not afraid to say again that it all depends on your diligence.Do not be too lazy to update the same old boards (for example, using a grinder and a special circle) and you will get a quite decent and pretty product.

Country washbasin: how to choose

A convenient option would be to install a washbasin next to the shower, with a single water supply system.

But you can also buy an independent washbasin, ready-made options are presented in large numbers in our catalog. Washbasins for summer cottages differ in the type of water supply, the presence of cabinets and heating. Such plumbing equipment can be installed in any convenient place: it can be an outdoor washstand or a washbasin inside the house.

There are several types of designs of country washbasins:

• with sink and cabinet;
• wall;
• on the counter.

The cost of such washbasins is low, especially if the water in the device does not heat up.

Wall-mounted washbasin

Such a washstand is attached to the wall, and a water tank is placed below. They can be mounted on any vertical surface with clips. Their volume rarely exceeds 5 liters.

Washbasin on the counter

A good solution for washing hands after earthwork is a hanging option, on a stand. Advantage - installation anywhere on the site. It consists of a metal rack, which is fixed on the ground and a tank fixed on top, with a volume of 10-15 liters. Under such a washbasin, it is not necessary to drain into a container - the water will be absorbed into the ground. It is only necessary to choose a place where the used liquid will not harm either buildings or crops.

Washbasin with cabinet

The most popular option for use in the country, they are also called "Moydodyr". Water in such washbasins goes into a container inside the cabinet. Or a full-fledged withdrawal system is used.As a rule, washbasins with cabinets are equipped with shelves and hooks for towels, often with a mirror.

Sinks are made of plastic, stainless steel, and the inside of the tank is coated with an anti-corrosion compound. A stainless steel sink will cost more, but is more durable and easier to clean. For the manufacture of cabinets, chipboard or plastic is usually used. The volume of the tank for such washstands does not exceed 30 liters.

The optimal value is an indicator of 17-22 liters - this is enough for a family of three. If you plan to use the equipment not only as a washstand, but also for washing dishes, then choose a larger tank.

Heated washbasin

A washbasin for a summer cottage with heating will add comfort if there is no centralized water supply on the site. A heated washbasin differs from a boiler in that water must be poured in manually, it does not come centrally.

The poured water is heated using a heating element, which is located inside the tank. The greater its power, the faster the water heats up, but more electricity is consumed. Such a device is safe: when there is no water in the tank, the heater does not work. The disadvantage of such washbasins is the small volume of the tank. As in the case of a shower, consider the possibility of country wiring.

If there is free space on your site and in a country house, dispose of it correctly. Comfortable living in the country, pleasant rest and efficient work will be complemented by the presence of useful furniture and equipment, for example:

An outdoor shower and a washbasin in the country are inexpensive, but in any case, useful designs that are easy and short to install.Choose ready-made solutions in our catalog and make your cottage even more comfortable place for living and recreation, as well as for useful work.

Types and types of wash basins

Depending on how your cottage is equipped, you have several options:

• Filled by hand (the easiest to make).
• Connected to plumbing.

Consider separately the characteristics of each type.

Filled by hand

This is the simplest washbasin.

Connected to the water supply

This is a more civilized model.

heated

The best that civilization has to offer.

To prevent the washbasin pipes from freezing in winter, drain the water and turn off the water supply before the onset of cold weather, insulate the water supply. It is possible to lay special pipes with a heating element in the outer contour of the insulation.

As you can see, each device has its own advantages and disadvantages. But, having weighed all the pros and cons, you can go directly to the most interesting thing - how can you make a washbasin in the country with your own hands?

What are there? Making the right choice

In order not to spend money on installing a separate water supply system, it is recommended to install a washstand in the immediate vicinity of the shower

You can pay attention to independent designs. The main design differences are in the presence of an electric heating system, a bedside table and the type of water supply.

Such products can be mounted anywhere: from a dwelling to a street gazebo. There are several types of washstands for giving:

• On a stand (pedestal).
• Wall (suspended) structures.
• With cabinet and sink.

With water heater

Such devices will help add much-needed comfort, provided that there is no centralized water supply on the territory.Heated washstands have significant differences from the usual boiler. For example, water must be poured into the tank manually, since there is no access to the common system. The liquid is heated by means of a heating element. For greater convenience, when choosing, it is recommended to use the comparative table, which is given by each manufacturer without exception.

Such devices are recognized as completely safe. If there is not enough water in the tank, the heating element will not work. Design flaws are not without, because the volume of the tank is small, and the cost of individual devices can be enormous. Do not forget about the possibilities of wiring, because in summer cottages this aspect is always given insufficient attention. In addition to a quality washbasin for a summer residence, you should also take care of a number of auxiliary accessories, such as:

Types of structures	Description	useful links
Shower	It does not imply the purchase of a full-fledged shower cabin. It is enough to take care of the drain and a small partition with a watering can.	Rating of the best shower cabins for 2020
Storage type heater	Allows you to save on electricity and have warm water at hand.	Rating of the best storage water heaters for 2020
dry closet	The need to solve such plumbing problems is simply necessary.	Rating of the best dry closets for 2020
electric stove	Either way, preparation is essential. If you stay in the country for several days, then family members will have to be fed.	Rating of the best desktop electric stoves for 2020
small refrigerator	To avoid poisoning, you should purchase a small refrigerator. Such devices are characterized by mobility and compact dimensions.	Rating of the best refrigerators for 2020

wall

Such devices are mounted on vertical surfaces. A water tank is installed near them. Suitable for installation anywhere. Clamps are used as fasteners. The volume of such washstands rarely exceeds the mark of 5 liters. It is this option that should be bought for a summer cottage, which is rarely visited.

With bedside table

This option is considered the most popular. Popularly referred to as "Moydodyr". Used water flows into a special reservoir, which is placed inside the cabinet. It is possible to connect a complete drainage system. Often, popular models are equipped not only with bedside tables, but also with mirrors, towel hooks and shelves. Sinks are steel (metal) or plastic.

The kit contains all the necessary tools and accessories. Steel products wash better, but are more expensive. Bedside tables are made of impact-resistant plastic or chipboard. The volume of the tank does not exceed the mark of 30 liters. The optimal indicator is 15-20 liters, which is enough for a family of 3 people. If you plan to wash there not only hands, but also dishes, then it is better to take a larger tank.

On the counter

A great solution to wash your hands after hours spent in the garden. Hanging devices can be installed anywhere within the site. The design is a metal rack, the fixation of which is carried out on the ground and the tank, which is mounted on top. A volume of 10-15 liters is enough to solve everyday problems. The drain container can be omitted, as dirty water will soak into the ground.When choosing a site, preference should be given to a remote area where excessive moisture will not harm either crops or buildings. Goods of the world's best manufacturers allow you to purchase a high-quality sink with all the necessary characteristics.

For premises

Indoor wash basins

If we are talking about homemade washstands on the street, then it is definitely worth mentioning the washstands in the room. The internal washstand is much more complex in design than its outdoor counterparts. It is clear that here you need to take care not only of its functionality, but also of beauty. In other words, it should harmoniously fit into the general surroundings of a country simple life. Most likely, this will be the most common type of internal washbasins - “moidodyr”. How to make this washstand out of wood? We will need boards 25 × 150 mm.

In vertical blanks, recesses must be cut in advance (depth 20 mm, width 8 mm). This can be done with a manual router. In horizontal blanks, spikes are cut accordingly using a conventional hacksaw.

The size of the future washbasin is largely determined by the dimensions of the water tank that we plan to use for it.

It is also important for us to know for sure the dimensions of the sink, which we will mount on the cabinet. After everything is cut to size and technological recesses are cut along with spikes, the washbasin is assembled like a designer. However, it would be better to fix the joints with wood screws

However, it would be better to fix the joints with wood screws.

The upper (or side) part of the structure has a niche where we should insert the finished water tank.

Moidodyr assembly

We strengthen the bottom of the washstand with slats (20 × 45 mm) at the same distance from each other. We close the back wall of the upper part of the "moidodyr" with plywood - from 3 mm and fix it with self-tapping screws. Of course, it is better to use moisture-resistant plywood for such a thing in case the water container leaks, but if there is none, it’s not scary.

As for the cabinet door, everything is simple here: we glue a square of 3 mm plywood with PVA glue to the frame of four interconnected small wooden planks on its back side. It remains to embed a lock with a figured handle. Everything, the wooden frame of the “moidodyr” is assembled. Now the final touch is grinding, painting the product, and then installing the sink. It will turn out very cute.

Homemade washstand in the house

There are a lot of options for washbasins and they are all good in their own right. The question is which design you prefer. Much, of course, depends on the functions that you assign to it. One way or another, a washstand / washbasin is convenient in every way. And if it's in the country, even more so. Therefore, we hope that this article was useful for you.

Oil can washbasin

Another simple washbasin option that motorists can make without throwing away the oil can and buying a water bottle with an overlapping valve stopper.

Step 1. First of all, you need to take a metal canister and rinse it well.

Step 2. You will also need to take the neck of a plastic bottle.It must be attached to the canister in the place where the water outlet will be organized, that is, the tap, and circled with a marker.

Step 3. According to the resulting contour, you need to cut a hole in the tank. You can use a drill and, having drilled a few holes, cut out in this way.

Step 4. The sharp edges of the hole must be sanded with a file.

Step 5 Using cold welding, you need to attach the plastic neck from the bottle, which was used earlier for marking, to the tank by inserting it into the hole.

Step 6. Now you need to screw the bottle cap equipped with a valve onto the neck - this will be the tap.

Step 7. After filling the tank with water, the washbasin can be used by opening and closing the water with a valve.

Advantages of a heated washbasin for a summer residence

When deciding to buy a heated washbasin, it is worth considering all the advantages and disadvantages of the device so that no problems arise during operation.

Pros:

• possibility of installation indoors and outdoors;

• a quick way to organize hot water supply;

• compact dimensions of the body, laconic design, harmoniously fitting into any interior or exterior;

• range of models with different tank volumes allows you to choose the most suitable option;

• economical consumption of water, energy resources;

• high-quality materials used in the production of washbasins ensure a long service life;

• the principle of operation and the device are so simple that even a teenager can do the installation;

• If necessary, a burned-out heating element can be replaced.

A heated washbasin attracts the attention of not only summer residents, but also residents of suburban villages.Even a pipeline brought into the house does not solve the problem of arranging a local hot water supply point right on the site

In addition, a stand-alone washbasin will always come in handy when the water supply is turned off.

One of the main advantages of designs with a heating element is the ease of connection, which does not require the involvement of outside specialists and unnecessary spending of funds for the services they provide.

Types of washbasins

The easiest option for a suburban area without a residential building and eyeliner is a washstand from a plastic bottle or eggplant.

The device is very simple, but indispensable during the landing period. You can do it like this:

• Find a 1.5-2 liter bottle.
• Fasten it to a pole or even a fence using simple metal clamps.
• Attach a small faucet. By the way, it is not necessary to run to the nearest store for it. You can do it with a simple syringe. A hole is made in the lid, the body of the syringe is placed in it, if necessary, you need to get only the inner part, which protects the washbasin from leakage.

A photo of the washstand for giving can be seen below. Even such a small design will save hardworking summer residents. Additionally, you can explore the types:

• hanging washbasin - you can buy it ready-made, but it’s easier to make it from an unnecessary container or even a barrel;
• washbasin on the counter - you can use the old frame from the bedside table;
• heated washbasin.

Each option can be played in different ways. You can find current offers and schemes below.

Heated washbasin: what is it and types

A sink for a country house with a heater is traditionally a pedestal, approximately in human height. There is a water tank on top of the cabinet.There is an electric heating element in the tank, which is powered by the mains through the use of a cord. At the bottom there is a large compartment, right under the sink, there is a tank for water that drains. This is not the best solution, if possible, it is rational to stretch the pipe from the washstand to the cesspool. On the market you can find a large selection of models of country washbasins. There are modifications with and without a water heater.

There are washstands without a compartment for draining water, they are especially suitable for those who already have all communications under the washbasin in a country house.

The materials from which products are made can also be different. The most popular tank option is a stainless steel product. Such a washstand can be placed on the street without worries: it is not afraid of natural phenomena in the form of precipitation. Yes, and resistant to mechanical damage. The most economical option is washstands with a plastic body.

On sale you can find the following types of washbasins for summer cottages:

1. Mounted. This product is a tank with a faucet in the shape of a rectangle, which is mounted on any strong vertical surface. There is a heater inside the tank. Such a heated washbasin without a bedside table can be mounted even outdoors under a roof, because the product is covered with a special anti-rust coating. True, when mounting outside, it is necessary to strictly observe all the safety measures prescribed in the instructions.
2. Mounted on anti-corrosion support. The most advanced type of wall-hung washbasin. Such a washstand can be arranged on the street, and the metal frame adds strength and stability to the product.
3. With cabinet.The most completed model of a country washbasin with a water heater. Such a country electric washbasin consists of a pedestal, which is made of chipboard, plastic or metal, as well as a sink made of polymers or metal, and a tank for heating water. A large cabinet can be moved without problems, because it is usually easy to assemble and disassemble.

The model with a pedestal looks like a stand-alone piece of furniture and can be connected to the sewer.

What it is?

A heated washbasin is a kind of bedside table made of plastic, wood or steel, in which the sink is mounted. In this case, the sink can be made both from the same material as the cabinet, and from a completely different one. A water heater is included with this design, which, if desired, can be replaced with a more powerful one. A heated washbasin is said to be designed to meet small household needs, such as cleaning hands after working in the garden or washing vegetables before serving. At the same time, it does not require special installation and can be installed almost anywhere in the local area, perfectly fitting into the interior of the cottage.

What should be considered when choosing?

According to the principle of operation, a heated washbasin is very similar to a conventional electric water heater. Their difference is that water is drawn into the water heater automatically from the water supply system, and water will have to be poured into this design manually. A valve is usually located on the washbasin tank, with which you can adjust the water pressure. The water heater inside the structure can have a different power, which will determine how quickly the liquid inside will heat up (see video).

To choose a washbasin with heating for a summer residence, it is necessary, first of all, to take into account your needs. For example, if you just need to wash your hands or fruits and vegetables in it from time to time, a tank volume of 10 liters will suffice, and if you need to constantly wash your hands and agricultural equipment after working in the garden, it is best to use a tank with a volume of 25 liters or more, as , for example, in the photo. In addition, it is necessary to take into account how many people can live in the country at the same time.

It is worth noting that most heated washbasins are able to maintain the selected water temperature, as well as independently turn off when it is reached. Such structures are equipped with thermostats. The washbasin can be installed anywhere in the cottage, where there is free access to electricity. However, it does not require grounding. As for the cost, it will depend on the quality of the material of manufacture and the power of the water heating elements. So, a plastic washbasin will cost less, but it will be less durable than, for example, a steel structure.

When installing a heated washbasin, it is imperative to provide a place where the used water will drain. So, the structure can be attached with a pipe to

• sewers, if it passes nearby;
• containers that were previously dug into the ground;
• a pit dug nearby, the bottom of which is lined with gravel.

Common Models

The most commonly used models of heated washbasins, according to numerous consumer reviews, are Aquatex, Moidodyr and Alvin (see photo). The Aquatex washbasin is equipped with a water heater that is powered by electricity. It can heat water up to 65°C in just an hour.Such designs fit perfectly into the interior of the cottage, as they are made mainly of wood. The sink is usually made of stainless steel, which makes the units more durable. The volume of the water tank is 15 liters.

Constructions by Moidodyr are able to constantly maintain the water temperature at 55°C, which is the best option. The volume of the tank can vary from 15 to 25 liters, which makes the washbasin suitable for large households. It is worth noting that the size of structures can be completely different - from the smallest to incredibly large, which must be taken into account when choosing.

The Alvin heated design can be used both in the garden and in the summer kitchen and garage. Thanks to its modern design, it will perfectly fit into any interior. Such units are made mainly of steel and painted in different shades. The volume of the tank is usually 20 liters, and it is most often equipped with a thermostat. The hole in the back wall of the structure allows you to connect the sewerage system. To choose between different models of washbasins, you need to remember that they differ mainly in the materials of manufacture and the power of the water heating elements. The better the components and the more powerful the water heater, the longer the design will last - this is evidenced by numerous reviews.

heated

Well, the most complex, costly, but at the same time comfortable option is a heated washbasin. As a rule, it is an improved version of the previous version, but it can also be located on a rack.

If you are inventing a heated washstand yourself, then do not forget to take care of the insulation of the wires and the mechanism for controlling the degree of water heating.

The article presented the main types of washstands in the country, their design and application features. Careful acquaintance with all the nuances and consideration of photos of country washbasins will help you make the right choice.

How to design a washbasin without the help of specialists

So, how to make a washbasin for a summer residence from the materials that are nearby? Remember that the washstand must be not only as simple and convenient as possible, but also multifunctional, that is, not only for washing hands in it.

The most economical is a design made from an ordinary plastic bottle. To do this, you will need a one and a half liter bottle or a five-liter eggplant. Cut off the bottom of the bottle.

Using a clamp or aluminum wire, fasten to a tree or any vertical plane. The bottle cap will serve as the dispenser in this design.

Pour water into a container. Opening the lid a little, we will see that the water will flow in a small stream.