Overview of Polish water fan heaters Vulkano

Available model lines

Small models are used as sources of additional heat

The best for heating indoor air are Volcano VR models. For full-fledged work, they do not need street air - it is taken directly from the building.

The following models are produced in 2019:

• Vulcano fan heater Mini with AC and EC motors;
• VOLCANO VR1, VR2, VR3 with AC, EC engines;
• heater Volcano VR-D.

Since 2018, the production of models with AC engines proven over the years has been reduced. Europe has switched to engines with moderate power consumption EC.Energy saving models save 16% of energy.

Volcano Mini

Heating fans are designed to heat the premises with the help of a coolant and distribute the flows by controlled shutters. The design contains a pair of heat exchangers with a coolant temperature of up to 130 degrees. Air consumption - 2100 cubic meters / hour. Noise of engines at the level of 52 dB. Weight 17.5 kg. The average cost is 21,000 rubles. Low cost, medium air consumption, jet length up to 14 m, the basis for active use in heating small and medium-sized rooms.

Volcano VR1

A popular line of fans with a power of 5 - 30 kW. Price 27000 rub. Water is used as a heat carrier under pressure up to 1.6 MPa. The temperature of the working environment is up to 130 degrees. The fan creates noise up to 56 dB. Supply voltage - 220 V single-phase network. Engine speed - 1380 rpm. This model is used for domestic needs in medium-sized rooms. Convenient in the absence of three-phase voltage.

Volcano VR2

The model, operating from 220 V, is able to heat a large area - a hangar, a warehouse, a sports hall

Thermal power of 8-50 kW heats a large area. This is interesting for sports grounds, shopping centers with a shortage of three-phase current. The model runs on 220V. The length of the jet torch is 22 m, the vertical one is 11 m. The cost of the equipment is 33,000 rubles. 2 heat exchangers with a total volume of 2.16 cubic dm. are responsible for the passage of air with a volume of 4850 cubic meters / hour.

Volcano VR3EC

Volkano fan heaters with a capacity of 13-75 kW are industrial equipment. The horizontal jet of air reaches 25 m, the vertical one - up to 15 m. This model of the Volcano has air heating - 5700 cubic meters per hour.This consumption is achieved by the operation of a small engine with a power of 0.37 kW. The efficiency of the Vulkan model makes it possible to use the heater to heat rooms of thousands of square meters. Durable grades of plastic protect against aggressive environments, ultraviolet radiation, withstand heat, cold, humidity. The devices of the series are small in size and attractive in design.

Volcano Mini EC

Energy-saving motors with a power of 95 W provide a horizontal flow of up to 14 m, and a vertical one of up to 8 m. The equipment is compact, which is necessary for small spaces. At the same time, the heating performance of the Volcano does not suffer, reaching 2100 cubic meters per hour. Thermal power 3 - 20 kW.

How to maintain volcano vr1?

The volcano vr1 heat exchanger must be regularly cleaned of dust and dirt. Especially before the heating season, we recommend cleaning the heat exchanger with compressed air from the louvre side. The volcano vr1 fan motor does not require much maintenance. The only maintenance concerns the fan. When dirty, you can clean the protective grid from dust and dirt. If the volcano vr1 is not used for a long time, the equipment must be disconnected from the power source. There is a risk that the volcano vr1 heat exchanger will defrost if the room temperature drops below 0°C and the temperature of the heating medium drops at the same time, especially when two-way valves are used.

Remember that buying VOLCANO VR1 EC New from us - GENERAL DISTRIBUTOR implies:

• free delivery of VOLCANO VR1 EC New to the shopping mall terminal in Moscow, Novosibirsk, Krasnodar;
• 5-year warranty (replacement of equipment with a new one within 5 years from the date of purchase);
• The possibility of returning VOLCANO VR1 EC New within 14 days, in accordance with Art. 502 of the Civil Code of the Russian Federation and art. 25 of the Law "On Protection of Consumer Rights".

	unit	Volcano VR1
unit heater row number	—	1
maximum air discharge	m3/h	5300
heating power range	kW	5-30
device weight (without water)	kg	27,5
maximum horizontal air reach	m	23
maximum vertical air reach	m	12

Needed in any room

The high demand for Volcano fan heaters lies in the fact that they can be installed absolutely in any room, they are suitable for heating the premises of apartments, private houses and cottages and are in demand in office, administrative buildings, as well as in children's and educational institutions, where comfort and safety are above Total. Also Volcano perfectly copes with heating of trading floors, car dealerships and warehouses. The efficiency and power of Volcano fan heaters make them indispensable for production shops and premises, sports facilities and large shopping centers.

Volcano VR3

	Parameters Tz/Tp
90/70	80/60	70/50	50/30
Tp1 °C	Qp m³/h	Pg kW	Tp2 °C	Qw m³/h	Δp kPa	Pg kW	Tp2 °C	Qw m³/h	Δp kPa	Pg kW	Tp2 °C	Qw m³/h	Δp kPa	Pg kW	Tp2 °C	Qw m³/h	Δp kPa
5700	75,0	39	3,31	32,6	64,5	33,8	2,85	25,1	54,3	28,4	2,39	18,4	33,6	17,6	1,46	7,8
4100	60,6	44,1	2,69	22	52,5	38,2	2,32	17	44,3	32,2	1,95	12,5	27,5	20	1,2	5,4
3000	49,5	49,2	2,19	15	42,9	42,7	1,89	11,6	36,3	36,1	1,59	8,6	22,6	22,5	0,98	3,7
5	5700	69,9	41,6	3,1	28,9	59,8	36,3	2,64	21,7	49,6	31	2,18	15,5	28,7	20	1,25	5,8
4100	56,8	46,3	2,52	19,5	48,7	40,4	2,15	14,8	40,5	34,4	1,78	10,6	23,5	22,1	1,02	4
3000	46,4	51,1	2,06	13,3	39,8	44,6	1,76	10,1	33,1	37,9	1,46	7,3	19,3	24,2	0,84	2,8
10	5700	65,2	44,1	2,89	25,3	55	38,8	2,43	18,6	44,8	33,4	1,97	12,8	23,7	22,4	1,03	4,1
4100	53	48,6	2,35	17,1	44,9	42,6	1,98	12,7	36,6	36,6	1,61	8,8	19,4	24,1	0,84	2,8
3000	43,3	53,1	1,92	11,7	36,7	46,5	1,62	8,7	30	39,8	1,32	6,1	15,9	25,8	0,69	2
15	5700	60,4	46,6	2,68	21,9	50,2	41,3	2,22	15,7	40	35,9	1,76	10,3	18,4	24,6	0,8	2,6
4100	49,2	50,8	2,18	14,9	41	44,8	1,81	10,7	32,7	38,8	1,44	7,1	15,1	26	0,66	1,8
3000	40,2	55	1,78	10,2	33,6	48,4	1,48	7,4	26,8	41,6	1,18	4,9	12,4	27,3	0,54	1,2
20	5700	55,6	49,1	2,47	18,8	45,4	43,8	2	13	35	38,3	15,4	8,1	12,8	26,7	0,56	1,3
4100	45,3	53	2,01	12,8	37,1	47	1,64	8,9	28,7	40,9	1,26	5,6	10,4	27,5	0,45	0,9
3000	37,1	56,9	1,64	8,8	30,4	50,2	1,34	6,1	23,6	43,4	1,04	3,9	8,3	28,2	0,36	0,6

If a different temperature is used, data regarding the performance of Volcano fan heaters are available on request.

Specifications

Currently, two models of Volcano heating equipment have been released - VR1 and VR2. There are also models of fan heaters Volcano VR MINI and Volcano VR3, but they are not widely used.

Models VR1 and VR2 have a temperature and corrosion resistant housing made of special plastic that meets all environmental control standards. In these instances, only reliable automation is used, which is very easy to manage.

The Volcano VR1 heater belongs to single row devices and has a power of 30 kW at maximum load. The second model has two rows, and the power indicator is increased by 2 times.

Water acts as a heat carrier. The maximum possible heating temperature of the working fluid for both models is 1300C with a heated air jet range of 25 m. In the first model, namely in VR1, 1.7 dm3 of water is used, and in the second - 3.1 dm3.

The maximum allowable working pressure is 1.6 MPa.

We must not forget that the use of pressurized water as a coolant requires additional protection with a possible increase in this indicator. But the conditions are also taken into account that when the temperature drops to negative values, the heat exchanger may break if there is water in the system.

Air heater VOLCANO VR1 EC New with power from 5 to 30 kW

Model (Model) 1-4-0101-0442 air heater

Fan heater VOLCANO VR1 EC (New) with a single-row heat exchanger and air flow up to 5300 m3/h

with EC motor

#LIFE OF VOLCANO VR1 EC fan motor
Required service life:
➢ 70.000 hours at 70% load and 35°C ambient temperature (8 years)
➢ 30.000 hours at 100% load and 55°C ambient temperature (3.5 years)

VOLCANO EC VR1 connection block with new type of EC motor ?

Selection calculator
to calculate the amount of Volcano VR1 EC and find out
boiler power for your room

Thermal power range, kW	5-30
Supply voltage, V	220
Motor power consumption, W	162 — 250
Motor type AC - 3-speed \ EC - stepless	EU
Number of heater rows	single row
Number of engine speeds	3
The volume of water in the heat exchanger, l	1,25
Maximum coolant temperature, С	130
Maximum coolant pressure, atm	16
Housing material	Plastic
Maximum current, A	1,3
Air consumption (productivity), m3/h	2800/3900/5300
Maximum suspension height, m	12
Airflow range (air jet length), m	23
The diameter of the branch pipes for connecting the coolant	3/4″
Weight, kg	27,5
Noise level, dB (A)	38/49/54
Moisture protection	IP44
Airflow range (vertical air flow), m	12
Dimensions, mm: WxDxH	700x425x700
Maximum engine speed, rpm	1430
Maximum ambient temperature	+ 60 degrees

Attention! The maximum operating pressure for liquid heat exchangers is 16 bar. The maximum pressure for which liquid heat exchangers have been tested is 21 bar

The maximum pressure for which liquid heat exchangers have been tested is 21 bar.

Fan heaters Volcano - description

Volcano fan heaters are water heaters equipped with heat exchangers and powerful fans. They provide heat supply to premises of any purpose. Their manufacturer is the Polish company VTS, which indicates the European origin of the equipment. It is safe to say about the highest degree of distribution of these fan heaters in Russia.Today they are installed in:

• repair shops and garages;
• supermarkets and hypermarkets;
• warehouse premises;
• car park premises;
• car dealerships;
• hangars and industrial premises.

The equipment package may include thermostats with servo drives, programmable control panels, two-way valves and much more.

In addition, the Vulcano fan heater is a smart choice for heating a greenhouse where heat is needed for growing crops in the beds.

Volcano water heaters have an extremely simple design. Their heart is productive heat exchangers through which hot water flows. The heat exchangers are blown by fans, the streams of heated air are sent through the outlet grilles to the outside.

Volcano fan heaters are elements of air heating systems. They can be used as the main modules of heating systems, and as auxiliary equipment. Powerful jets of warm air fill the heated rooms with heat. At the same time, these fan heaters cannot be called thermal curtains - they are precisely heating devices.

Traditional thermal curtains prevent the penetration of cold into the premises, acting as auxiliary heating equipment. Volcano fan heaters are closer in functionality to heat guns.

The main advantages of Volcano fan heaters:

• Low-noise fans - provide a comfortable environment with minimal noise.
• Compactness and low weight - all this facilitates installation work.
• High performance - individual models of air-heating units from Volcano can drive through themselves up to 5000 and more cubic meters of air per hour.
• A simple connection diagram - just connect the fan heaters with flexible hoses of a suitable diameter to the pipes with the coolant. Electricity is also required for their operation - it rotates the fans.
• Robust construction made of durable steel grades and corrosion-resistant plastic.
• Modern universal design - allows you to fit the equipment into any interior without spoiling their appearance.

The undoubted advantage is the affordable cost of Volcano fan heaters.

If you plan to buy Volcano at the lowest prices in Russia and get proper after-sales service, we advise you to contact only authorized dealers.

Pros and cons of water models

Appliances manufactured by a Polish manufacturer are recommended for use in facilities where rapid heating of the room is required. The coolant in them is water. It heats up to a certain temperature and then gives off heat to the air circulating inside the unit. With the help of a fan, it enters the room through the guide blinds. Thanks to this principle of operation, the device is able to quickly warm up any room.

Watch the video, performance test of this model:

In addition, even volcano mini fan heaters, unlike classic radiators, are easy to install and have great power. They are already successfully working at many facilities and have managed to prove themselves only from the best side.

Installing the volcano vr2 fan heater does not require specific knowledge and can be done independently. It can be connected both to a centralized heating system and to an individual boiler. In this case, the heat will be evenly distributed throughout the room.

The main advantages of Volkano brand equipment are:

• High performance;
• Low cost of maintenance and operation;
• Automatic regulation of parameters;
• Easy installation;
• Insignificant noise level;
• The ability to create the most efficient heating system in comparison with all available.

Features of the Volkano VR2 model

The developers of the device made sure that it could be used to heat even air masses containing caustic substances or high humidity. This is indicated by a molded plastic case. For its manufacture, a material is used that can withstand heating up to 130 ° C and is immune to corrosion.

Watch a video about this model:

As decorative elements, it uses colored side plates. They can be ordered additionally for a specific color scheme of the room design. The two-row heat exchanger of the volcano vr2 fan heater allows you to develop power up to 6 kW at a pressure of 1.6 MPa. Its connection to the heating system is carried out using the nozzles located on the rear panel of the device.

The jet of thermal air from the device enters the room through the guide grilles. Moreover, its direction is regulated by one of four possible positions. The Volkano VR1 fan heater is attached using special studs or a mounting bracket, which makes it possible to turn the jet in any direction.

Installation and operation of equipment

When choosing a place to install a Volkano fan heater, you need to take into account various nuances. Among them, special importance is given to the possibility of free access for service maintenance. Since the device needs regular preventive maintenance, it must be mounted in a place where it will be freely accessible.

However, in addition to this, other aspects must be taken into account, such as:

1. Supply of pipes with heat carrier;
2. Connection to power supply;
3. Rational direction of the stream of heated air.

When mounting the fan heater on the wall, the distance from it to the surface cannot be less than 0.4 m. At the same time, the height of the device should not exceed 8 m.

Installation under the ceiling requires a distance of 0.4 m from its surface. In this case, the unit can be located at a height of 4 to 12 m. Studs or a console can be used as fasteners. But since they are not included in the package, you will have to purchase them separately. Mounting holes are provided in the upper and lower panels of the fan heater for fastening to a support.

Applications

Fan heaters with increased IP protection are used in car washes

The units are not suitable for heating private houses. The only area of ​​application in housing is for heating verandas, indoor spaces without the constant presence of a person. Vulkan devices are designed for heating rooms with high ceilings: hangars, production areas, warehouses, greenhouses. The owners of garages, car washes, swimming pools, trading floors also use them in their work.

Thermal curtains Volcano are successfully used at the entrances to the premises, protecting the internal heat from the cold outside air.

The heaters are used independently and for reheating the premises when there is a shortage of stationary heating units.

The use of Vulkan automation helps to save up to 70% of fuel for boilers (coal, gas, pellets, diesel). The systems operate at a coolant temperature range of 50-120 degrees. For work, the air already in the room is used. The higher the ambient temperature, the lower the cost of heating it.Fan heaters deliver heated air to any point in the room where heat is required, but stationary heating radiators are not installed due to controlled shutters. Streams of warm air are constantly mixed and exclude unheated zones in the room.

The Volcano water fan heater has found wide application in car washers. For wet rooms, automatic equipment with increased security IP54 is used. Fan heaters warm up an icy car in just seconds. Dry quickly after washing.

In summer, roof fans are used to ventilate the room.

The use of fan heaters in hot weather expands the functionality. They are used as fans, mixing the air in the room and creating favorable working conditions.

From non-standard methods of application, the use of a fan heater with refrigerant can be noted. Then, to prevent the formation of condensate, a water collection tray is placed below. If necessary, a hose is adapted to drain the liquid. With this use, the units are also used to cool production facilities in the heat. However, the cooling capacity is lower than the thermal one. During operation, condensate is carried inside the room. To prevent this, the fan speed is reduced.

Positive performance

Fan operation

As soon as the Volcano fan heater appeared on the market, it immediately attracted the close attention of target buyers. And all because Polish manufacturers have offered the world universal equipment that can work in tandem with any heating system - whether it is a heating network, a boiler room or an ordinary water heating boiler of any type.

And this is not the only significant advantage that the Volcano fan heater has.

Therefore, the technique has the maximum technical performance. The noise level, for example, produced at the power limit of the unit, is only 51 dB. And under normal operating conditions, it does not exceed 28 dB

This technical feature attracts the attention of those who own areas and premises with increased noise level requirements.

Almost all the positive qualities are manifested in the process of equipment installation. Thanks to the use of innovative solutions, the fan heater has small dimensions, while its power is enough to solve the tasks. The installation allows you to make a hidden connection or put the device on display, making it part of the interior. This circumstance was especially appreciated by the owners of shopping centers and conference halls - those objects, the external design of which is of great importance.

Volcano - high technology heating

Climatic conditions in most of the territory of our country are such that heating costs make up a significant part of any budget. From family to corporate. In addition, the heating systems used everywhere, despite their diversity, have one significant drawback: static heating of the air around the heat source. At the same time, the lion's share of warm air, due to the natural circulation of the air flow, rises to the ceilings. This reduces the efficiency of using energy for space heating by half. This problem is especially relevant in houses of old buildings, insufficiently insulated, with outdated communications, in industrial premises with high ceilings, children's institutions and hospitals.Here, heat losses are even greater and reach up to 80%. Just think! From 50 to 80% of the energy expended goes nowhere! However, you pay for them out of your own pocket. Almost all buildings and structures using classical heating systems have some other heat loss. And the proportion of these losses is very significant. Is it possible to reduce losses and increase the efficiency of heating devices and systems?

Generalization on the topic

As you can see, the Volcano fan heater has good technical parameters. It increases the efficiency of the existing heating system and creates the most comfortable conditions for the operation of an industrial, commercial or sports facility.

Read more:

How to properly repair a fan heater with your own hands

Navien gas boiler - technical specifications, design features and model range

Danish Grundfos circulation pumps - specifications and design features

What are smoke sandwich pipes - their features, advantages and disadvantages

Modern Wilo circulation pumps - technical data and operational advantages

Fan heater VOLCANO VR3 EC (New)

Model (Model) 1-4-0101-0444 air heater

Air heater VOLCANO VR3 EC New with power from 13 to 75 kW
with three-row heat exchanger and airflow up to 5700 m3/h.

with EC motor

#LIFE OF VOLCANO VR3 EC fan motor
Required service life:
➢ 70.000 hours at 70% load and 35°C ambient temperature (8 years)
➢ 30.000 hours at 100% load and 55°C ambient temperature (3.5 years)

!*!*Depending on the amount $ of the order, an additional % discount or free delivery to the point of issue of VOLCANO VR3 EC (Volcano VE-ER Three E-CE) in your city!​

ENGINE PROTECTION VOLCANO VR3 EC
Thermal protection: The control unit provides thermal protection for the motor.
When the engine temperature exceeds 90°C, the power starts to decrease, which leads to a decrease in heat generation and engine cooling.
If the temperature exceeds 105°C, the engine will be stopped.
The engine will start automatically when the temperature drops to 75°C.
#Protection by supply voltage:
The control unit provides protection against low and high supply voltage. The electronics shuts down the motor if the voltage is not in the required range.
#Rotor lock protection:
The control unit de-energizes the motor protection if the rotor shaft is blocked and cannot rotate. The electronics performs 25 cycles of restarting the engine and, in case of failure, turns it off. Next, a manual restart of the engine with power off is required.
#Fault or loss of motor phase:
The control unit is equipped with protection against motor phase failure/distortion. In case of detection of a phase break or phase imbalance, the electronics will immediately turn off the engine.
#Overcurrent protection:
The control unit provides overcurrent protection. In the event of an overcurrent, the electronics will immediately stop the motor and attempt to restart it.
#Rotor acceleration error protection:
The control unit controls the acceleration of the motor shaft. If the electronics detect a deviation in acceleration (when the rotor is damaged or difficult to turn), the motor will be restarted.After 25 cycles (one second cycle) of a failed restart, the engine will shut down. Next, a manual restart of the engine with power off is required.
Notice!
The control unit prevents the engine from overheating! When the temperature reaches 105°C, the electronics stops the engine and restarts it again when the temperature drops to 75°C. However, if the motor is overheated, turn off the power for 20 minutes before servicing it. If the engine overheats, the metal parts are very hot and may cause burns.
If the controller starts to reduce output power during operation, this may be the cause of overheating.
Make sure air passes through the motor housing.

VOLCANO EC VR3 connection block with new type of EC motor ?

Scheme of connecting Volcano vr3 to the coolant

Selection calculator
to calculate the amount of Volcano VR3 EC NEW and find out
boiler power for your room

Thermal power range, kW	13-75
Supply voltage, V	220
Motor power consumption, W	218 — 370
Motor type AC - 3-speed \ EC - stepless	EU
Number of heater rows	three-row
Number of engine speeds	3
The volume of water in the heat exchanger, l	3,1
Maximum coolant temperature, С	130
Maximum coolant pressure, atm	16
Housing material	Plastic
Maximum current, A	1,7
Air consumption (productivity), m3/h	3000/4100/5700
Maximum suspension height, m	12
Airflow range (air jet length), m	25
The diameter of the branch pipes for connecting the coolant	3/4″
Weight, kg	31
Noise level, dB (A)	43/49/55
Moisture protection	IP44
Airflow range (vertical airflow), m	12
Dimensions, mm: WxHxD	700x425x700
Maximum engine speed, rpm	1400
Maximum ambient temperature	+60 degrees

Attention! The maximum operating pressure for liquid heat exchangers is 16 bar. The maximum pressure for which liquid heat exchangers have been tested is 21 bar

The maximum pressure for which liquid heat exchangers have been tested is 21 bar.

Heating a car wash or service station

To create favorable conditions in such workshops, air-heating devices are often used. Due to the fact that these heaters have excellent compactness, there is no need to wonder about its convenient placement.

Due to the fact that the EuroHeat manufacturing company provides a lifetime warranty on the cases of its products, it is possible to judge the quality of the material used, which is not amenable to mechanical damage and premature wear.

The units are extremely easy to use and installation will require a connection to a hot water system, which can be supplied by an additional space heating boiler. The fan forcibly blows the Volcano heat exchanger, which has a special structure of its circuit resembling a labyrinth.

Particular attention is paid to air, which creates a heat flow. An important factor is that it is taken from the same room where it is installed.

Thanks to this, there is no need to mount additional air outlets to the street. The fan itself has a well-thought-out design of the blades, thanks to which it works almost silently, thereby not distracting from work.

The air-heating unit in winter ensures the maintenance of optimal temperature indicators and participates in the fight against excessive humidity. But also thanks to its use, the use of additional burners, electric radiators, and so on is excluded. Equipment from EuroHeat is designed to increase the safety of the work process.

In auto repair shops, it is necessary to choose the right place for installing the device, and it is also necessary to connect it to the heating system and eliminate the possibility of violating the integrity of the pipes through which the coolant is supplied. An important factor when choosing an installation location is the possibility of unhindered passage of a jet of heated air.

Most often, air-heating units are used in tandem with the main heat generator, which can be gas, diesel or one of the types of solid fuel boilers. Antifreeze is known to be used as a coolant, which has proven itself well at low temperatures, but it is necessary to consult a specialist before using this substance, because it may affect some of the seals that are part of the device.

See the following video for the features of Volcano heating units.

Available model lines

Next, we will consider the most popular models of Volcano fan heaters in Russia. There are not very many of them, so the choice can be made pretty quickly. Let's start with the most simple and low-power models.

Volcano Mini

This model range includes Vulcano Mini fan heaters with power from 3 to 20 kW. Their design provides for two heat exchangers, which can receive a coolant with a temperature of up to +130 degrees.The power of the electric motors used is 0.115 kW at a speed of 1450 rpm. The air flow from the bowels of these fans breaks forward at a distance of up to 14 meters, providing heating of fairly large rooms. When working in a vertical position, the height of the warm jet is up to 8 meters.

The air consumption for Volcano Mini fan heaters is 2100 cu. m/hour. As a result, they are suitable for use in heating systems for small and medium-sized premises. The engines are not the quietest - they make noise at the level of 52 dB. The weight of the equipment is 17.5 kg. Estimated cost - from 21 thousand rubles.

Volcano VR1

Before us is a fairly popular line of fan heaters. The cost of equipment starts at 28.6 thousand rubles, excluding possible discounts. The power of the models varies in the range from 5 to 30 kW. The number of rows of heat exchangers in the units is 1, their volume is 1.25 cubic meters. dm. Ordinary water with a maximum temperature of up to +130 degrees is used as a heat carrier. its pressure should not exceed 1.6 MPa.

To drive air through the heat exchangers, these fan heaters use electric motors with a power of 0.28 kW and a noise level of 56 dB. They are powered by a single-phase network with a voltage of 220-230 V. The rotational speed of the electric motors is 1380 rpm.

Volcano VR2

The presented fan heaters have impressive technical characteristics. Their power is from 8 to 50 kW, which allows you to heat large areas - they are well suited for gyms, car workshops and supermarkets. The maximum air consumption for these units is up to 4850 cubic meters. m/hour.The heat carrier is hot water with a temperature of up to +130 degrees and a pressure of up to 1.6 MPa.

Inside the Volcano fan heaters, 2 rows of heat exchangers are installed, their total volume is 2.16 cubic meters. dm. A small electric motor with a power of 280 watts is responsible for running the air masses. To power the fans, a power supply with a voltage of 220-230 V is required. The length of the horizontal jet of warm air is up to 22 m, vertical - up to 11 m. The cost of equipment is from 32 thousand rubles.

Volcano VR3EC

This range includes quite powerful fan heaters - their power varies from 13 to 75 kW. The equipment passes through itself up to 5700 cubic meters. m of air per hour, showing high performance. The length of the horizontal jet of air reaches 25 m, vertical - 15 m. The electric motor with a power of only 370 W is responsible for all this - this is an energy-saving model that consumes a minimum of electricity.

Volcano water fan heaters are equipped with three rows of heat exchangers at once. Their total volume is 3.1 cubic meters. dm, the coolant used is heated water with a temperature of up to +130 degrees, the pressure in the heating circuit should not exceed 1.6 MPa. The design of the fans uses particularly durable grades of plastic with UV protection. It withstands any operational load, successfully transferring heat, cold and moisture. Also, the series is distinguished by an attractive design and compactness.

Volcano Mini EC

You can not pass by this series, equipped with the same energy-saving electric motors. These fan heaters are equipped with two rows of productive heat exchangers - for 2100 cubic meters pass through them per hour. m of air masses.Permissible coolant parameters are standard - not higher than 1.6 MPa and not higher than + 130 degrees, the volume of heat exchangers is 1.12 cubic meters. dm.

A miniature electric motor is responsible for pumping warm air into the rooms. It consumes only 95 watts of electricity, rotating at a frequency of 1450 rpm. Despite the minimum power, the fan creates a horizontal air flow up to 14 meters long or a vertical one up to 8 meters long. The equipment is extremely compact - it is designed for heating small spaces. By the way, the thermal power of Volcano Mini EC fan heaters is from 3 to 20 kW.