TOP 10 best remedies for clogged pipes: the best drugs on the market + how to choose the right one

Folk methods

In the event of a blockage in the sink siphon, put one end of a long flexible hose on the outlet of the mixer, and insert the other into the siphon. After that, you just need to turn on hot water and act on the blockage with it for a while. If the obstacle does not arise in the siphon, but further, it should be removed in order to reach the right place with the hose.

A good remedy for clogged pipes is laundry detergent or dishwashing products. They fall asleep or poured into drains, adding a large amount of boiling water from above. Detergents in combination with very hot water are excellent at removing grease.

The method is not suitable for plastic pipes: they do not tolerate too hot water, the maximum recommended temperature for them is about 50 ° C.

Instead of washing powder, you can use other products.

For example, caustic soda. To clean it, it is enough to pour a tablespoon of the substance into the hole and pour boiling water over it. It should be borne in mind that soda has a bad effect on the skin and significantly damages the enamel.

Less harmful is ordinary baking soda. Its required amount is also one tablespoon; you can pour it with vinegar or boiling water. In the first case, you need to wait until the “boiling” is over, and then rinse the pipe with hot water.

Efficiency

How to determine which is the best of the means offered to you?

Everything is very simple: the most effective drug will be the one that contains the maximum amount of acid or alkali. Obviously, granulated Potkhan with 60% sodium hydroxide will be more effective than liquid Tiret containing no more than 15% sodium hypochlorite. Information about the composition of any sewer cleaner is always on its packaging.

The composition of the liquid preparation "Mole".

When using strong drugs, be prepared for violent chemical reactions - boiling and splashing. Take care of your eyes and skin: alkalis and acids in high concentrations cause chemical burns.

Reaction when cleaning the sink.

Solvent cost

№	Product name	Average cost (₽)
1	MOLE (1.2 L)	77
2	YPLON DRAIN CLEANER	145
3	DEBOUCHER	113
4	TIRET (1L)	420
5	SANFOR	145
6	CHIRTON "CLEAN DRAINERS" (60 GR.)	35
7	mr. MUSCLE	87
8	BAGI "POTHAN"	564

Problems with clogged pipes in the bathroom and kitchen lead to discomfort, so it is necessary to carry out monthly preventive maintenance of sewers and drains. If obstruction has appeared, then you need to choose an effective remedy to get rid of congestion and unpleasant odor. To do this, you should use the rating of the best pipe cleaners in 2019.

Attention! The above information is not a buying guide. For any advice, you should contact the experts!

Operation features

A stainless steel chimney is quite popular today, but like other chimneys, it needs to be checked and generally looked after from time to time. Below we will tell you how to do it right.

1. The first thing to do when using a steel chimney is to carefully inspect the heater before each season. At times, it may need to be cleaned of soot and other dirt.
2. Next - you need to check the draft when the time comes for the first ignition. If not, then you need to find out what's wrong. As a rule, a simple warm-up with improvised means and a subsequent check of traction with a match is enough.
3. It is necessary to inspect the chimney channel, check if it is clogged with soot. You can get rid of it with a soft stainless steel brush and a plaque softener.
4. From time to time, you can lay aspen firewood, which can eliminate soot in the chimney.
5. Proper use of the stove requires the use of wood from deciduous trees that does not contain resin. It should also be noted that it is impossible to use cutting plywood and chipboard for ignition.

It is necessary to take into account the presence of a number of operating features that determine the life of the chimney

Cleaning the drain with folk methods

Boiling water can be used to eliminate small pipe contaminants, such as soap or grease deposits. At the same time, you qualitatively eliminate unwanted precipitation on the first 2-3 meters of pipes. Further, the water cools and ceases to dissolve the fat.

To remove a small amount of hard water, use baking soda. She falls asleep directly into the pipe. Following it, vinegar (9%) is poured along the walls. The ratio is 1:1 (half a glass). Due to the neutralization reaction, the structure of the scale (plaque) is destroyed.

Since vinegar and soda react quite strongly, the drain must be closed with a cork. In this form, the pipeline is left for a while (the duration of such cleaning depends on the degree of contamination of the pipes), and then washed with boiling water.

You can use a mixture of salt and soda, but it will act more slowly. It is also washed off with boiling water. You can also combine different means.

With small blockages, a plunger will help

The use of chemicals contributes to the elimination of bacteria and the smell of decomposition. So you clean and disinfect the pipeline at the same time. At the same time, funds from “chemistry” are undesirable while cleaning the blockage in the bath. On its surface, particles of detergent can remain, which will damage your skin during bathing.

Physical methods for cleaning pipes from blockage

If the sewer is clogged thoroughly (water is standing or leaving very slowly in the sink, toilet bowl), an iron cable or a plunger is used to clean it. The cable directly breaks through the blockage.Since it is impossible to predict exactly where it was formed, the length of the cable must be at least 10m.

With the help of a vacuum, the plunger draws out a part of the lump of dirt (hair, food residue, etc.) from a narrow section of the pipe, loosens it, and then pushes it further along the pipeline with a pneumatic impact.

Cleaning pipes with water through a cone under high pressure

At the moment, in addition to traditional cone-shaped plungers, more effective syringe-like ones are produced, as well as specialized ones for cleaning toilet drains (they have a specific shape for ease of use).

Special chemicals for cleaning pipes

For high-quality cleaning of the pipeline from the inside, many products have been developed based on caustic soda, lime or strong mineral acids. The most popular and famous of them:

At the same time, when cleaning the pipeline with Potkhan and Flup, you must be extremely careful - be sure to use protective rubber gloves and, preferably, increase the ventilation of the room where the work is carried out (for example, open windows). "Potkhan" is produced in the form of a powder, "Floop" - in the form of granules. Both products, in addition to the effectiveness of cleaning surfaces, are also distinguished by a high price.

Rules for the Use of Drain Cleaning Chemicals

If you are going to clean the pipeline with one of the above products, carefully read the instructions for use

It is important not to overexpose the solution on the surface of the pipe, as the substance will begin to corrode the walls, cause rust, holes in the water supply and other unpleasant consequences. All these substances are washed off with plenty of warm or hot water.

If you use powdered substances, you should make sure that they act in the right place, and do not settle on the surface of the sink, toilet bowl, etc. and corrode it. To do this, remove all the water from above and below the blockage - it may be necessary to partially dismantle some sections of the pipeline (which is not necessary during gel cleaning).

Chemicals for removing blockages in sewer pipes

For each of the proposed chemicals, the volume recommended for high-quality cleaning is indicated. You can use more, but this is usually inappropriate and sometimes even harmful.

The unused substance will simply wash away further into the pipeline and settle on its walls. If it is not washed off in a timely manner, it will continue to react as intended.

Any of these tools should be used once every six months to prevent the occurrence of sewer blockages, as well as eliminate harmful bacteria and other organisms in the pipeline.

The volumes of active ingredients (as well as types of products) during emergency cleaning are larger than during planned ones, which also testifies in favor of regular preventive work.

Why can pipes clog?

Sewer line clogging is a fairly common occurrence. It is necessary, of course, to correct the current situation as soon as possible, since it becomes impossible to use water in the apartment without sewerage, and this is not the most pleasant situation.

To select a remedy, they are determined with the cause of the blockage:

• a plug of hair, debris, etc. has formed;
• the lumen of the pipe narrowed to a critical size due to the layering of grease and dirt on the walls of the sewer;
• improper installation of the pipeline has led to the fact that the water does not leave by gravity, but stagnates in the pipe.

As a rule, all causes are easily eliminated if the rules for the installation and operation of the pipeline are observed, and if a blockage has already occurred, there are chemical and mechanical ways to deal with it.

The lumen of the pipe has decreased - what is the reason

Very often, pipes become clogged as a result of an increase in fatty deposits and rust, and, as a result, a narrowing of the sewer clearance occurs. Especially often this happens in houses with cast-iron or steel sewer pipes.

The water that is supplied through the pipeline has a certain chemical composition. It contains various salts, biological particles, chlorine residues after cleaning.

In addition, water that has been used, contaminated with detergents, and more enters the sewer. This chemical cocktail reacts with the pipe material, the oxidation process takes place, and rust appears.

The corrosion process is long, it does not stop in a humid environment, and gradually the inner part of the pipeline becomes completely covered with rust.

Plastic pipes do not corrode. However, with poorly processed joints, if there is a plastic burr, protrusions, gaps and other irregularities on the inside, an increase in dirt with subsequent blockage of the pipe can also occur.

Sticky fat settles on a rough surface, which is not washed off with cold water. Hair and food residues after washing dishes stick to fat, growths on the walls increase exponentially, until the pipe lumen in the most vulnerable place is completely clogged.

To prevent the formation of such plugs, you can install a grease trap under the sink - the device filters the effluents entering the sewer.

Foreign body in the sewer - a dangerous situation

A plug of garbage, hair, wool, sand and other waste that does not belong in the sewer occurs when the rules for using the sewage system are violated. Some believe that literally anything smaller than a drain hole can be thrown into the sewer. This is a big misconception.

If such a blockage has formed in the pipe as part of the wiring around the apartment, one or more plumbing fixtures are decommissioned, and if the riser is clogged, several apartments can be cut off from the sewer at once. It is unlikely that the neighbors will say thank you

Non-dissolving, bulky debris can get stuck in the pipe, gradually accumulating smaller particles, hair residue and grease from the kitchen sink. All this will turn into a huge plug inside the sewer system.

With such problems, folk methods or chemical means cannot be coped with. The best solution is cleaning with a plumbing cable.

The pipe is systematically clogged - it's a matter of installation

When laying sewers, it is important to observe a slope of about 3%. Then the drains will be discharged under the action of gravity

Water with such a slight slope is in good contact with the walls and carries away all the particles.

If the slope is insufficient, this will lead to the fact that the drains will stagnate, the dirt from the walls will not be washed off, but will continue to accumulate until a blockage forms. However, the slope of the sewer is the case when the rule "the more the better" does not apply.

If the angle of inclination of the pipe is too large, the water will fly by quickly and will not have time to capture the remnants of household waste that will remain on the walls.

Another rule for laying sewer pipes is to try to avoid turns. 90° turns are especially dangerous. The more points of change of direction, the greater the risk of clogging.

Tips for choosing the right product

In order for sewer pipes to properly perform their function, they must be constantly monitored. But regardless of care, a clog can appear in the sink or bathroom. After the occurrence of such a problem, it must be solved quickly, inexpensively and without risking your health.

Today, a huge amount of a wide variety of chemicals is used to clean pipes. They are sold in one of three types: gel, liquid, and powder. Guidelines for choosing a sewer cleaner depend on personal preferences, the type of sewer pipes and the degree of clogging of the system.

It is recommended to give preference to formulations in the form of granules or gel. The former are considered the most effective, while the latter are safer for human health.

Before buying, be sure to pay attention to the composition. In the vast majority of the best formulations, the main active ingredient is the so-called caustic soda.

It is a reagent that dissolves plaque and pollution of organic origin in the shortest possible time.

A-tensides are also added to some natural chemicals. Do not be afraid of them - these kinds of substances are found in almost every dishwashing detergent. They are completely safe and biodegradable.

The following article, which is worth reading for owners of city apartments and country houses with organized sewage, will acquaint you with the proven means and methods for punching blockages in the toilet.

Granules

2. Unicum Tornado

This granular preparation helps to obtain an excellent result even if the case is completely hopeless - the water does not go away, and it is impossible to find out the specific cause of the blockage. As the people who used this tool themselves say: the products are characterized by speed in both the bathroom and the kitchen. The reason for this lies in the active substance used: these granules contain a high concentration of sodium hydroxide. We must not forget that it has a high level of causticity, so when working with it, you will have to follow the instructions for use without fail, use various personal protective equipment for the skin, respiratory organs - thick rubber gloves, goggles, respirators, and so on. By the way, it is strictly forbidden to pre-mix the granules with water. Work must be carried out in a room with good ventilation, natural or forced type.

Products act very quickly - the whole operation, as a rule, takes no more than three to five minutes. During this time, the granules manage to get to the blockage, simultaneously releasing active substances from themselves, which quickly dissolve in water and begin to actively act on the contaminants on the pipe walls. When the product reaches the very blockage, it dissolves fatty deposits, breaks down food residues and grinds hair to a powder state.As a result, it is much faster to break through the blockage than when using products manufactured in other formats. Store in a dry place, away from children and foodstuffs.

Advantages:

• Clears blockage as quickly and efficiently as possible;
• Completely removes contaminants from pipe walls;
• One package is enough for a long time.

Flaws:

Extreme care is required, as this is a very strong chemical. Granules to eliminate blockage Unicum Tornado

Granules to eliminate blockage Unicum Tornado

1. BAGI Pothan (600 g)

In the first place in this section of the best sewer cleaners is Israeli-made products, which are of excellent quality and efficiency. Works great with pipes made of any materials - cast iron, plastic, aluminum, iron, and so on. This is a combined remedy that includes not only caustic alkali, but also a whole set of inorganic acids, various additives and surfactants. In percentage terms, alkali is the most here - about 30% of the total production. There are much fewer active substances: from 5 to 15%. The formula of the composition is chosen in such a way that it is able to cope not only with fats and food residues, but also with hair, animal hair and even rust. The products are quite expensive, but consumed slowly, after its use it will not be necessary to carry out prophylaxis for about 4-5 months.

When working with granules, it is necessary to ensure high-quality ventilation of the room.Tiles, marble, enamel and hands should be protected from contact with this composition. Water dilution is strictly prohibited. You need to work with gloves and a respirator, since when the blockage is dissolved, gas is formed that will come out of the sewer pipe. It not only has an unpleasant odor, but also can cause serious harm to human health.

Advantages:

• Acts very quickly;
• Eliminates any blockages, regardless of their nature;
• Does not harm sewer pipes;
• The packaging is equipped with a child protection system.

Flaws:

• It is very expensive;
• When it enters into a chemical reaction with particles of blockage, seething begins, smoke is released, an unpleasant and very dangerous gas for health.

BAGI Pothan (600 g)

Folk methods

At home, not only the use of hot water, but also other ingredients in the kitchen will help to cope with a serious congestion. If the situation becomes more complicated and ordinary water does not help, in a separate bowl it is recommended to prepare a composition of the following ingredients:

1. Lemon juice.
2. Vinegar.
3. Soda.
4. Salt.

To provoke a chemical reaction, vinegar and soda must be present in the composition. Ordinary table salt will serve as a catalyst, and lemon juice will serve as an alternative to vinegar. Since its cost is higher, hostesses prefer to use vinegar.

It is necessary to fill in the prepared powder after treating the pipes with hot water. Leave the sink alone for an hour. Upon completion, it remains to re-flush the pipes with hot water.

Mechanical cleaning

To deal with large accumulations of food, debris or grease, it is not necessary to use a drill. As a rule, plumbers use:

1. Plunger.
2. special wire.

The first option at home is used much more often. Its work is provided by a change in pressure. As a result: complete destruction of the blockage, or damage to its structure. At the end of the work, it remains only to rinse the pipes with hot water.

The second tool is used in everyday life much less frequently. The main purpose of the wire operation is the elimination of blockages located at great depths. It consists of two parts: a cable, at the end of which a hook and a brush are fixed. The design is quite thin, which allows you to quickly deliver the brush to the place of work.

It is important to take into account that in order to use the device, you must have at least an approximate idea of ​​​​the location of the blockage.

Household chemicals

The most powerful remedies for blockages in pipes are various chemicals.

Today, thanks to the development of the chemical industry, there is a large selection of pipe cleaning products that differ in quality and speed of action, and in cost.

To remove the blockage, it is enough to pour or pour the agent into the hole leading to the pipe and leave it for a while. At the end of the procedure, flush the pipe.

The most popular means for releasing blockages:

1. Tiret ("Tiret") - used for significant blockages. It is distinguished by the absence of ammonia smell, does not pose a danger to pipes made of any materials. The tool is produced in Poland and is available in two forms: for prevention and for cleaning itself. The use of the first type, less caustic, makes it possible to use the second less often.
2. Mr. Muscle ("Mr. Muscle") - available in the form of foam or gel. The first type is more efficient.The composition contains a substance that dissolves not only fat, but also hair, food waste, and in addition, destroys bacteria and eliminates unpleasant odors. Produced in Italy and also suitable for all types of pipes.
3. "Mole" - an alkali-based liquid solution. Perfectly dissolves organics, including hair and pieces of fabric. Suitable for pipes of any material. The remedy can also be used as a prophylactic, once every one or two weeks.

We should not forget about prevention: the periodic use of weak solutions of cleaning agents or even plain hot water harms pipes much less than a single impact of concentrated substances.

Gels

2. Gel to eliminate blockages TIRET

On sale you can find two varieties of this product - one is intended for domestic use, the second for industrial production. The composition contains all the necessary substances and components that are able to actively eliminate fatty plugs and organic accumulations. It is worth noting that the substance itself does not evaporate, does not have an unpleasant odor, so there is no need to ventilate the room during or after use, and you will not have to use respirators either. The composition contains chlorine-containing bleach in a percentage of its 5-15%. It uses a sodium hypochlorite solution, which, during contact with pollutants, oxidizes and dissolves them in water. The volume of anionic surfactants does not exceed 5%. They perfectly fight fatty layers, which also become soluble in water. However, it should be borne in mind that these are very aggressive substances, so you will have to work with gloves.

Non-ionic surfactants are resistant to hard water, break down the blockage into simple components that will be discharged into the central sewer with the help of a stream of water. With the help of this tool, it is possible to get rid of even deaf plugs, when the water does not go down the drain, but simply stands in the sink. The gel is much heavier than water, therefore, under the influence of gravity, it will reach the blockage and dissolve it, and this will not take too much time. After it was possible to get rid of the cork, the pipe is additionally washed with a large volume of hot water. this will help remove any remaining dirt and dissolve grease.

Advantages:

• Very thick gel, which helps it to envelop the blockage over the entire area;
• Convenient ergonomic packaging;
• Insignificant expense;
• A large number of active active ingredients.

Flaws:

• It is necessary to work in rubber gloves;
• If a traffic jam has formed, you will have to wait up to several hours.

Gel to eliminate blockages TIRET

1. Sanfor Pipe Gel

It is used to prevent and get rid of even very serious blockages. The gel is quite thick, so it can be poured directly into the water - it will get to the clogged area on its own within a couple of minutes. At the same time, it should be remembered that it is strictly forbidden to close the drain of the sink or bathtub, since access to fresh air is required. A positive result is noticeable after some five minutes. The dense structure helps to effectively act on the blockage throughout its area. The gel can quickly cope with hair, food debris, body fat and a number of other contaminants that have fallen into the sewer. With it, you can quickly neutralize and remove unpleasant odors.The gel is absolutely safe for all types of sewer pipes, including plastic. It kills all harmful bacteria almost instantly.

The composition contains chloride compounds, which are a fairly effective disinfectant. The gel is poured into the sewer pipe, after which you need to wait about 5-15 minutes. If the blockage is very strong, then it will be necessary to leave for a longer time. Prevention with such a gel is carried out less often than usual - about once every two months.

Advantages:

• Excellent efficiency in the fight against even very serious blockages;
• The smell is not very pleasant, but much better than that of a clogged sewer;
• Acceptable cost;
• Minor expense;
• You can carry out preventive measures much less frequently.

Flaws:

The composition contains chlorine, which can corrode the skin of the hands.

Sanfor Pipe Gel

Chemical cleaning of pipes

The appearance of an unpleasant odor, a decrease in the rate of flow of liquid or a rise in the water level requires urgent cleaning measures, otherwise the pipe may become completely clogged and fail altogether.

Cleaning sewer pipes with chemicals can be done without difficulty, but only with the use of protective equipment. Before starting work, you need to wear a mask, gloves, goggles. The room in which the work is carried out must be well ventilated. Modern substances contain acid or alkali. It is not allowed to use products with different chemical composition at the same time, since individual components can react with each other and thereby harm the system. You need to work in the following sequence:

• pour or pour the required amount of funds into the drain;
• add 0.1 to 1 liter of water;
• wait from 3 minutes to 1.5 - 2 hours (manufacturers indicate in the instructions the duration of the product);
• flush the sewer with plenty of water (about 2-4 buckets).

A list of the best, according to experts, remedies for eliminating blockages in pipes is proposed. When compiling the rating, customer reviews were taken into account. Based on the recommendations, you can make the best choice.

Overview of popular tools

How can I clean the sewer pipe, as well as pipes in the bathroom and in the kitchen? There are some of the most popular and effective tools that will help answer the question: how to clean the sewer pipe and other pipes. Consider them:

"Minute gel". A fairly effective product that clears blockages in this way: you need to pour the product into the drain and wait a few minutes. Then rinse the connection with water. The price for 500 ml of such a reagent is, as a rule, about 29 r, which is a fairly budget option in combination with efficiency, however, it is unlikely that this drug will be able to clean sewer pipes with a dense fatty plug.

"Tiret". A popular cleaner for clogged plastic pipes. Consider the cleaning process using such a preparation in more detail:

1. Pour 250 ml of the substance into the drain hole of the sink or bathtub.
2. Leave the substance in the pipeline for about 15–20 minutes.
3. Next, a large amount of hot water must be poured into the drain hole.
4. After that, you need to check whether the cork that prevented the movement of water has been removed.

The main disadvantage of this tool is its price (about 250 r).

Mole is the most popular pipe cleaner available in both powder and liquid form.

"Mole". By far, this reagent is the most popular tool for cleaning pipes from blockages. How to clean pipes using the "Mole"? For this you need:

1. First you need to pour, as in all previous cases, the liquid "Mole" into the drain hole. The volume of the poured substance is from 50 to 150 mm.
2. It is necessary to leave the substance in the pipes for 2-3 hours.
3. After that, the pipeline is flushed with plenty of water.

The cost of 1 liter of liquid "Mole" is approximately 69 rubles.

"Floop". A common and fairly effective substance that allows you to remove blockage from a plastic structure. However, such a substance can not cope with every blockage. It is an affordable, powdery reagent and does a good job of cleaning the right pipe at home. Consider the method of its use:

1. First of all, the substance is poured into the drain hole.
2. Next, you need to pour a certain amount of hot or cold water into the drain hole. The water temperature depends on the type of product.
3. We wait no more than 15 minutes and flush the pipeline.

The price of such a tool is approximately 50 rubles.

Means for cleaning plastic pipes "Chistin". A feature and, at the same time, the main advantage of this substance is its versatility. "Chistin" is able to cope with pipe blockages of a different nature. The sequence of actions when using this product is as follows:

1. Carefully pour 250 ml of product into the drain.
2. Leave the remedy for 15 minutes.
3. At the end of the procedure, we clean the pipes from the drug with plenty of water.

You can use a universal tool suitable for all types of pipes

The cost of this substance is an average of 47 p.

"Mister Muscle". A very well-known tool that helps to cope with clogged plastic pipes. Refers to powdered products.

The use of such a substance is devoid of all sorts of difficulties:

1. Gently pour the powder into the drain.
2. Pour a small amount of water (about a glass) down the drain.
3. Wait about half an hour.
4. The pipe is then flushed with plenty of water.

Such a reagent is the most effective, however, its cost is about 87 rubles.

It is worth noting that the reagents, the cost of which is the highest, are also the most effective. In any case, the choice depends on the specific situation and consumer preferences.

All of the above drugs will help you deal with various blockages and answer the most pressing question: how to clean a plastic sewer pipe.

Causes of blockage

In any apartment or private house, a channel system is installed that removes sewage. However, regular operation leads to the settling of various contaminants, which leads to clogged pipes.

The main factors causing blockages are:

• The use of the pipeline for other purposes. Ingress of sparingly soluble substances and compounds into the pipeline: food residues, hygiene products and pieces of rags or sponges, which are pressed into a lump, thereby blocking the flow of water;
• Errors in the design of sewerage. If the installation of pipes does not comply with the norms, such as the angle of inclination, turns or pipe connections, then it is necessary to change the entire sewer system to prevent blockage;
• natural deposition process.The active use of soap, detergent and protein content over time causes corrosion, so it is easier for residues to linger on the surface of rusty pipes;
• Lack of prevention. To keep the pipes clean, it is sometimes necessary to carry out preventive measures - light pipe cleaning.

Prevention of blockages in the sewer system

In order to avoid such problems, it is worth adhering to some ordinary rules:

1. It is necessary to throw away leftover food in the trash before washing the dishes;
2. A piece of toilet paper, rags, sponges or hygiene products thrown into the toilet can gradually form a blockage, so it is necessary to throw household waste into the trash can;
3. The habit of washing off cement, sand and plaster residues through the sewer also provokes a congestion, so you should not resort to such actions;
4. It is worth applying a pipeline cleaner once within a month so that any residue does not accumulate on the surface of the pipes.

Care and maintenance of a stainless steel chimney

For a more efficient operation of a stainless steel chimney, follow the recommendations below.

1. Before lighting a boiler or stove for the first time, it is necessary to check in advance whether there are any foreign objects or debris in the flue. If it is, then you need to take some long tool and push it through to the revision. When the debris is there, it is necessary to open the revision channel, pull it out of the pipe, and after getting rid of the debris, the chimney and revision channels are cleaned of soot with a brush.
2. Household waste must not be thrown into a working oven or boiler for burning, as it may worsen the condition of the chimney.
3. As a rule, softwood logs are not thrown into solid fuel heat generators.The reason is the resin content, which will quickly accumulate. The only exception is aspen logs, which can create a high fire and burn out soot in a chimney.

There are a few rules that need to be followed in order for the chimney to work properly.

From time to time it is necessary to inspect the roof on the roof, if it is made of metal. This is done to detect rust that may have appeared on the outside of the pipe. Yes, it can even hit "stainless steel", which is quite unusual.

What to do when such a problem is found?

1. Clear the area around the pipe.
2. Dismantle the problematic piece of pipe.
3. Clean, sand and degrease the work surface.
4. Holes and cracks - close up carefully.
5. Rinse with hot water and then dry thoroughly.
6. Fill all the cracks found with a special sealant.
7. Take a silicone nozzle, put it on the pipe, fix it with self-tapping screws for greater strength.

Mistakes made during the arrangement of the chimney will lead to the reappearance of rust on the pipe or its transition to the roof.

The roof should not rust if everything is done correctly.

Installation Recommendations

The recommendations below will help you properly install the chimney so that it functions without any difficulties.

1. If you put a pipe with a height of five meters or more, then you can achieve good traction.
2. The length of horizontal sections should be up to one meter, no more.
3. Installation of a chimney on the street or in an unheated room involves the installation of thermal insulation material.
4. If the chimney passes through a roof constructed with combustible materials, a spark arrester must be installed.

If you strictly follow the suggested recommendations, you can install a chimney without any problems.