Water lily sink: tips for choosing and installing when located above the washing machine

Installing a sink above an electrical appliance

The equipment installation technology is quite simple and includes three main stages. Let's take a closer look at each of them.

Fixing the bowl

To attach the water lily sink to the wall, use the brackets that come with it. The master only needs to fix them at the right height and hang the bowl.

Let's get to work:

• We mark the wall.We draw a line corresponding to the top panel of the washing machine. We will make the rest of the marks relative to this feature. We try on the bowl, not forgetting to leave a gap between the sink and the washing machine. Its value depends on the type of siphon. We outline the holes for the fasteners. If the bowl is located close to the bath and it is planned to install a common mixer, we check whether the length of its spout is sufficient.
• We drill holes. We use anchor bolts or dowel fasteners as fasteners.
• Install brackets. We do not completely tighten the bolts yet, leaving small gaps of 5 mm.
• Apply silicone sealant to the back of the sink. The composition is applied in a strip at a distance of 5-10 mm from the edge of the bowl. We carry out a similar procedure with the protrusions of the brackets, where they come into contact with the surface of the sink.
• We install the bowl on the brackets. To do this, we put the shell eyes on the metal hooks and fix it to the wall with dowels or anchor fasteners.
• Fully tighten the bolts securing the brackets.

The drain of the “water lily” sink is located as close as possible to the back wall of the bowl

We mount the siphon

It is recommended to attach the siphon to the sink before the brackets are tightened. Install the device in this order:

• We assemble the assembly, guided by the scheme, which the manufacturer must include in the packaging with the product. Do not forget to thoroughly coat all sealing elements and threaded connections with silicone grease. We tighten the thread very carefully, otherwise the plastic parts may not withstand the force and break.
• We find a pipe for connecting a washing machine at the siphon and put a drain hose on it.The resulting connection must be fixed with a clamp with a screw tightening. So we can be sure that the pressure of the water drained from the tank of the washing machine will not break the hose.
• We connect the outlet of the siphon to the sewer. Masters advise to additionally bend the corrugated pipe outlet in the form of a knee and secure it with insulating tape or soft wire. This is necessary to prevent the possible appearance of an unpleasant odor from the sewer, since in the flat siphons that the water lilies are equipped with, due to their design features, the water seal is very often broken.

The flat siphon for the sink is equipped with a special pipe for connecting the drain hose from the washing machine

Installing the mixer

The design features of a flat sink suggest the absence of a faucet. The best option for such devices is a mixer mounted on the wall.

The most commonly used model is with a long spout, common for a bathtub and a washbasin. In some cases, a hole is provided in the water lily body for installing a mixer.

It is installed in strict accordance with the manufacturer's instructions after the installation of the siphon is completed and the bowl is finally fixed to the brackets.

In the process of installing the mixer, do not forget about careful sealing. All seals must be lubricated with silicone grease.

Threaded connections are sealed with sanitary tow with paste or fum tape. We tighten the nuts on the mixer hoses very carefully. They are made of rather brittle zinc alloys, excessive force can simply destroy them.

After the installation is completed, we carry out a trial run and carefully inspect all connections for possible leaks.

If the “water lily” is equipped with a hole for the mixer, it is installed in strict observance of all instructions from the manufacturer

A bathroom sink mounted above a washing machine is a practical solution that helps to save and efficiently organize free space.

It is very easy to implement it in your home. You need to choose the right electrical appliance and plumbing equipment, it will be easiest to purchase a special kit. They are offered by many manufacturers. You can install such a tandem yourself.

During installation, it is important to remember the need to ensure electrical safety and perform all work carefully, observing all the requirements of the instructions.

How to save space in the bathroom

The bathrooms in our apartments are extremely small, so we have to constantly invent universal ways to arrange the necessary equipment in them. It is precisely for solving the issue of placement in a small area that a water lily sink is well suited.

Water lily sinks are excellent plumbing fixtures for small spaces. They can be of different models, and since they are installed directly above the washing machine, manufacturers produce variations that fit various types and sizes of washing machines. Even in the cramped bathroom there is a place to install such a sink.

The developers of the water lily sink also take into account which washing machine will be located under it.

Types of water lily shells

The shape of the water lily shell can be square or rectangular, round or semicircular, but its main difference is that the bowl is shallow, usually with a flat bottom, otherwise the washing machine will not fit under the plumbing fixture.The depth of the shell is about 20 centimeters. Of course, this is not quite what we are used to, but over time, such a difference may even be liked.

The water lily sink can be square

Water lily sinks vary in size, which allows you to choose them for an existing washing machine. The standard dimensions of the washing machine are 600x600 mm. In accordance with this, the width and depth of the shells vary - 600x600, 640x600, etc.

Plums of water lily shells can also be different: vertical and horizontal. Keep in mind that only horizontal is suitable for installing a washing machine. Keep this in mind when choosing your sink. In shape and size, siphons are more like shower drains.

The round water lily shell looks aesthetically pleasing, in the spirit of the Greek thermae

When choosing the material from which the sink is made, please note that not only earthenware, but also plastic can serve as it. Depending on the type of faucet, there are two types of water lily sinks: light and uni

In the light category there are models that are suitable for almost any type of washing machine, they do not have a hole for the mixer. This allows you to create stylish washbasins with a special elegance, the so-called lux-light. But the view of the uni has a hole for the mixer of the standard version

Depending on the type of faucet, water lily sinks come in two types: light and uni. In the light category there are models that are suitable for almost any type of washing machine, they do not have a hole for the mixer. This allows you to create stylish washbasins with a special elegance, the so-called lux-light. But the view of the uni has a hole for the mixer of the standard version.

Photo gallery: water lily shells in the interior

Features of combining a sink with a washing machine

For an optimal union of two designs, it is better to choose a front-loading washing machine. The recommended height of the eraser is 70 centimeters. In this case, the sink located above it will be at a height of 85 centimeters, which is the norm for use by a person of average height.

Sets for comfortable use of both devices:

• a water lily sink in conjunction with a narrow washing machine;
• water lily sink with mini washing machine;
• washing machine and sink included.

Buying a set (washing machine and sink) will cost less than buying each product separately

The most rational option is to buy a kit that includes a sink and a washing machine. Thus, all possible inconsistencies during installation are excluded. The dimensions of the sink will be slightly larger than that of the machine, which will allow it to be used for unloading laundry. Another plus: the kit is cheaper than buying each device separately.

Advantages and disadvantages of sinks over a washing machine

The main advantage of this arrangement is space saving. For small apartments, it is sometimes very difficult to choose another option. A kitchen or corridor is not the most convenient place to connect a washing machine.

The design of the washing machines is neutral and fits well with the modern style of the bathroom. In addition, you can connect to the water supply from the riser in one place, as well as crash into the sewer, which reduces the amount of work and materials. Usually the siphon that comes with the kit has an additional pipe for connecting the drain from the washer.

And finally, the third advantage is the convenience of washing, which all housewives will appreciate. Sometimes pre-washing of linen or other manipulations is required, for which at least a small sink is needed. And in this case, everything is nearby - both the machine and the bowl with cold and hot water.

There is only one drawback in the close proximity of the washbasin and washing machine - the danger of water getting on the electrical parts of the machine. Therefore, when installing equipment, everything possible must be done to exclude such a situation.

water lily models

Often, a water lily is an almost flat square bowl up to 20 cm deep.

Model Features

• . This wall-hung sink will keep its newness and cleanliness even if we use inexpensive cleaning mixes.
• , since the water lily does not occupy a separate place.
• .
• .

Scheme of the device Water lilies over the washing mechanism.

• , for example, a miniature compact or larger models.
• , as well as shared with a bathroom, but there are also models with a mixer.
• - a deep water lily is preferable over a low machine gun. By the way, a deep bathroom sink keeps all the splashes from washing.
• (you can use them from an old sink). The length of this support is 32 cm, which will not require additional alterations in the bathroom (in total, the depth of the machine is 45 cm plus the drain pipe behind the machine is up to 17 cm, and in the end it is only 60 cm).

Types of shells

Now they produce 3 main types:

• Water lily;
• Water lily Bolero (with vertical drain);
• Water lily Lux (with horizontal drain).

A novelty from the manufacturers - Marble water lily. The dimensions of this product are convenient: width - 64 cm, height - 14 cm, depth - 59 cm.

Washing machine selection

Some manufacturers make washing machines specifically designed to be installed under the sink. Of the well-known companies, Zanussi, Electrolux, Eurosoba and Candy are engaged in the manufacture of such models. Basically, all such models are designed for a small load of laundry - usually up to 3.5 kg.

Special models of small-sized washing machines are produced specifically for use in combination with a sink

Many owners of even small bathrooms, not intending to sacrifice the performance of washing machines, purchase models of standard sizes with a larger load. However, the height of the residents should also be taken into account, since the sink, with a washing machine height of 700 mm, will be raised to a level of approximately 890 ÷ 900 mm from the floor, and with a height of 850 mm - even up to 1040 ÷ 1050 mm .

Options for placing the sink-"water lilies" on the wall

As mentioned above, the depth of the washing machine must correspond to the same parameter of the sink, taking into account the necessary clearance against the wall - this criterion must be observed not only for comfortable use of the washbasin, but also in order to ensure electrical safety.

Perhaps the most rational solution is to purchase a ready-made kit, despite not the highest loading rates of the washing machine.

But still, if it is possible to purchase a set of equipment, then it will be most convenient to stop at this option, since you don’t have to invent and adapt anything. In the kit, the manufacturer has already taken into account not only all sizes, but also the external design of the elements - they look in a complex, as a whole.

What makes up the total height of the working panel of the water lily sink

On the diagram presented for example, you can see what the total height of the working top surface of the sink-sink will be made up of. This is the height of the washing machine itself and, taking into account its adjustable legs, the height of the brackets, plus the thickness of the front edge-side of the sink itself.

Even a flat siphon still has a certain height

But if a flat drain siphon is located under the sink, then its height should also be taken into account.

Examples of correct and erroneous installation of the sink above the washing machine

The diagram shows examples of the correct (a) installation of the machine, and performed with typical mistakes made:

b - Inconsistency of the type of siphon with the chosen installation scheme - the drain pipe of the sink has a sharp turn at a right angle, where blockages will inevitably form over time.

c - the discrepancy between the sizes of the sink and the washing machine, the front panel of which remains completely unprotected from water ingress from above.

This is interesting: Do-it-yourself installation and fastening of a suspended wall-mounted toilet bowl: we cover the issue

Proper selection of equipment

The first step is to familiarize yourself with the features of choosing a washing machine. In theory, you can give preference to any one you like, but the washbasin located above it for comfortable use should ultimately be at a height of no more than 60 cm.

The depth of technique also has limitations. This parameter should be in the range from 34 to 40 cm. With this in mind, we can conclude that an extremely compact washing machine can be installed under the sink.

Basically, their capacity is small and occasionally allows loading more than 3-3.5 kg of dry laundry.Such solutions are not suitable for everyone, so in such situations, some people prefer standard models.

When choosing one or another technique, at least 25 cm should be added to its height. This indicator together makes up the washbasin and the gap that is between the planes of the appliances.

It is a little more difficult to find the optimal depth of technique. It's good when the sink completely hides it. The best option is if the bowl protrudes beyond the washing machine in the form of a visor of small size.

In this case, the equipment is reliably protected from drops of water, which without fail fly around during the operation of the bowl. In this situation, it is better not to purchase a washing machine in which the control panel is located on the top of the lid.

A suitable option is the control unit, which is located on the front of the device, which not only makes it more comfortable to use, but also ensures its splash protection. When choosing a washing machine, it must also be taken into account that it will not work to place it close to the wall, since it is necessary to leave a gap of about 8 cm, in which engineering communications will be located.

As a result, it turns out that preference can only be given to a small-sized or very compact model, which has a depth of no more than 40 cm. When choosing a washbasin, certain difficulties also arise.

Above the washing machine, exclusively flat-type sinks are installed. In this case, standard bowls with a drain in the middle are not suitable.In the assortment of stores you can find special water lily washbasins, the main feature of which is the location of the siphon and the drain hole at the back of the bowl on the side or back wall of the product. The sinks of this variety can have the following types of drain:

• Vertical. A flat-type siphon is installed under the drain hole itself. The key disadvantage of this system is that the element is placed above the washing machine, which means that in case of leakage, there will be wiring problems or a short circuit. A significant advantage is the excellent outflow of water.
• Horizontal. In this case, the siphon is located very close to the wall, and some of the drain is in a horizontal position, which is why there is a high probability of blockage. The advantage lies in the high level of safety of the electrical device, since in this situation the siphon is located at a sufficient distance from it.

The shape and dimensions of water lily shells are varied, so among their assortment you can easily choose the model that is best for you.

Like ordinary washbasins, they are equipped with holes for fixing the faucet, a drain-overflow system, plugs and a number of other accessories. If in the future you have to install a sink that is built into the countertop, then you can choose any optimal one.

Design pros and cons

When planning the arrangement of the bathroom, it is important to think through every little thing in order to organically fit all the elements into a single small space.If the room has a place for a bathroom, then the presence of a sink is not necessary, but when a booth is installed, the lack of space for comfortable hand washing, washing, brushing teeth and other hygiene procedures becomes very noticeable. That is why in small bathrooms it is common practice to combine the sink with a washing machine.

That is why in small bathrooms it is common practice to combine a sink with a washing machine.

Saving space in the presence of useful functions is the main advantage of combining a sink with household appliances. In addition, the sink for such cases should be unusual, which often adds some charm to the room, highlights it and even decorates it. Placement above the washing machine allows you to combine drains and minimize the installation work of both elements.

There are also some serious shortcomings in this case.

• Fitting household appliances to the size of the sink and the dimensions of the room. If you buy an ordinary machine, it is not always convenient in terms of using the sink and makes it difficult to use. Non-standard cars are more expensive and hard to find.
• Due to the non-traditional dimensions of the machine, the amount of laundry that fits into it will be much less than in conventional devices, which will be very inconvenient if the family consists of a large number of people.
• To combine the sink and the machine, a conventional product will not work, since the drain should be located closer to the back wall, and the smallest depth of the sink is recommended.
• Due to the design features of the “water lily” sink, with a side and rear drain, not all the liquid will go away, so it will need to be removed on your own. This will increase the time to care for the product.Among other things, the sink will need to be cleaned regularly, especially if it has a slot-shaped drain.
• It is problematic to make a quick installation due to the lack of free space in the bathroom. It will not be easy for even an experienced craftsman to mount everything necessary to install a sink over a machine, not to mention a person without proper experience.

How to choose equipment

A certain type of washing machine and washbasin is suitable for a twin installation. Let's consider them in more detail.

Washing machine selection

A large and roomy washing machine under the sink will not get up, so you need to choose from compact models. The main selection criteria are front loading, height within 60-70 cm, depth - no more than 50 cm. Below are several models that are suitable in size for installation under the washbasin.

Candy Aqua 114D2

Main characteristics:

Zanussi FCS 1020 C

Main characteristics:

Electrolux EWC 1350

Main characteristics:

Eurosoba 1000

Main characteristics:

Sink selection

Sinks designed to be mounted above the washing machine in the bathroom have the common name "water lily", which they received for the flat shape of the bowl.

When choosing such a washbasin, pay attention to the following criteria

bowl shape

Water lily sinks are available in the following forms:

• Square with straight or rounded edges;
• round;
• oval;
• Rectangular (with countertop);
• Non-standard form.

bowl dimensions

The size of the bowl is selected based on the dimensions of the washing machine. The main criterion is that the washbasin should be slightly larger than the washing machine and completely cover it. This will ensure maximum protection of equipment from water ingress on the electrical part.

Drain type and location

Depending on the location of the holes for the water lily drain, they are divided into three types:

1. Drain in the center of the bowl. Such models are practically no different from ordinary sinks, but when installed, a gap remains between the body of the machine and the bottom of the washbasin, since additional space is required to connect the drain pipe.

2. Models with a rear drain allow you to install the washbasin almost close to the body of the appliance. The siphon is located behind the body of the machine, so access to it and the drain pipes is difficult, and in some cases, to clean the drain, you will need to pull out the washing machine. The hole for the mixer in such washbasins is shifted to the side, since there is a siphon in the center from the bottom of the bowl.

3. With the location of the siphon on the side and back of the bowl, which makes it easier to access it for revision work. In addition, this arrangement of the drain hole allows you to make sinks with an unusual organization of water flow.

Most Popular Models

Here are some popular models of water lily shells.

TECHNOLIT KOMPAKT

One of the cheapest models. It is made of cast marble, has dimensions of 600 mm in width and 500 mm in length, the thickness (height) of the bowl is 182 mm. It has a rear drain, an overflow hole and a central mixer installation. The price of the product is from 8000 rubles.

Water Lily Compact

The Water Lily Compact sink has a non-standard shape, thanks to which it can be hung over a machine installed in a corner. The bowl is made of sanitary faience and has dimensions of 535×560×140 mm. The hole for the installation of the tap is located on the left side of the bowl, and the drain is on the right in the back. There is an overflow hole. The price is about 8500 rubles.

SANRIF ULTRAMARINE

This sample of sanitary equipment has strict rectangular shapes with right angles, a central mixer installation and a side drain, there is no overflow hole. The bowl is made of artificial stone, its dimensions are 600×600×110 mm. The price of this sanitary ware is about 11,000 rubles.

Santa Leader

This washbasin with countertop is made of cast marble and measures 1200×480×150 mm. Products are produced for the installation of a washing machine to the right or left of the bowl. A feature of Santa Leader is that an ordinary bottle siphon is suitable for connection.

Washer under the sink: the pros and cons of the solution

Owners of small bathrooms may think that installing a sink over a washer is an absolutely win-win solution. Indeed, this option has a lot of advantages. First of all, it is an opportunity to organize the space as efficiently as possible by combining the layout of the upper and lower tiers of the room.

If you place a few more shelves or a cabinet above the sink, the space will be fully utilized. Thus, even in a small room it will be possible to place the necessary household appliances.

In addition, on sale you can find a variety of washing machines and sinks in style, which will decorate the interior of the bathroom.

However, along with the advantages, this solution also has disadvantages. And quite significant. First of all, it is insufficient electrical safety.

The washing machine is one of the electrical appliances for which contact with water is unacceptable. The sink located above the equipment is connected to the water supply, which is a potential electrical safety hazard.

Even a slight leak can cause moisture to enter the machine and damage it. Therefore, for installation above the washing machine, you should choose special sinks with a siphon located at the back of the bowl.

Installing the washing machine under the countertop, in which the sink is built-in, saves space in the bathroom

Their design is made in such a way that even in the event of a leak, water from the bowl does not fall on electrical equipment. Such shells are called "water lilies", they are sold in hardware stores.

Using water lilies is safe, but may not be entirely convenient. This is due to a non-standard siphon. Its design is such that the likelihood of blockages increases, since the water does not drain vertically, but horizontally. In addition, spare parts for siphons of this type are not always available for sale.

A distinctive feature of water lily shells is the location of the siphon. It's in the back of the bowl

If it was not possible to purchase a special sink or for some reason it cannot be used, there is another solution. The washing machine is installed under a countertop common with the sink.

It looks like this: a worktop of sufficient length is installed, on one side of it under the base there is an electrical appliance, on the other - a built-in sink. This solution is safer in terms of the use of electricity, but requires a sufficient amount of free space. Another unpleasant moment is associated with the height of the washer.

Standard models have a height of about 85 cm, if you install a sink above such a device, it will be extremely inconvenient to use the latter. You can, of course, build a semblance of a podium, but for small bathrooms this is not always possible.

Practice shows that the height of the equipment located under the sink should not exceed 60 cm. Thus, you will have to buy a special model.

They can be found in the lines of well-known manufacturers. Very often, sinks are also included with such devices, which are ideally suited to all parameters of the machine. Such a purchase will be the best option for installation.

These are all the main disadvantages of installing a washing machine under the sink. Apart from some inconvenience from the fact that when washing you can not come close to the bowl, because the place under it is already taken. But they get used to it pretty quickly. It must be admitted that all these disadvantages usually do not outweigh the advantages of such an installation, therefore such solutions are quite viable and in demand.

How to install a recessed sink in the bathroom

The built-in countertop washbasin is a practical and convenient option for medium to large bathrooms. The space under the countertop is used to install a washing machine and a cabinet or cabinet where you can store household chemicals and various little things.

The shape of the mortise bowls can be round, oval, rectangular or fancy. Ceramics, artificial stone, metal, glass and even wood treated with water-repellent impregnations are used for manufacturing.

Installation Features

The sink is mounted in a pre-prepared hole so that its sides rise above the countertop by 1-2 cm or are flush with its surface.Communications are hidden inside and do not spoil the interior with their appearance.

Installation can be carried out in 2 ways - from above or below. You will need a tape measure and a marking pencil, a jigsaw for cutting a hole, a mounting tool and fasteners, an FUM tape.

How to choose

First of all, you need to choose a sink in accordance with the width of the countertop. When cutting a hole, at least 50 mm must remain to the edge of the supporting surface, otherwise an edge that is too thin may not withstand, crack or break under load. Measure the countertop and, knowing its width, choose the appropriate option.

For a large family, you can buy a double sink, then the queue for the washbasin can be avoided. They can be round, square or oval. When installing, additional reinforcing elements (brackets) are provided.

When choosing a sink, you need to consider the location of the mixer. It can be mounted on a bowl or countertop, so in the latter case, additional space will be required to install it.

Mounting from above

In this way, you can install a sink with sides located above the surface of the countertop. To draw a hole, the washbasin is turned upside down and outlined with a pencil. But this is only suitable for symmetrical shapes. If the sink is non-standard, a template is made.

The hole should be 10-15 cm narrower than the contours of the bowl, so an additional line is drawn parallel to the one already drawn.

Carefully cut a hole in the countertop with a jigsaw. A sealing tape is glued to the edges of the sink, installed in the selected niche, the mixer, supply hoses and siphon are connected.

Mounting from below

With this method, the sink can be installed flush with the work surface.It is held by gluing into a small groove selected by a cutter in the table top. The table top does not have to be permanently fixed because it will need to be turned over.

Installation from below is more laborious than from above. Use a template made of plywood or a sheet of plastic, with which a hole is cut. Then the edges are ground, processed with a cutter. The shell is inserted and glued upside down. After the glue has hardened, the countertop is put in place and fixed. Connect water and sewerage.

Water lily shell installation process

Before you install a washbasin over a washing machine of this variety, you need to make sure that it is complete. In this case, the sink is hinged, which is why brackets are required for its installation.

Basically, they are supplied with the bowl, as their shape may vary. If the brackets are not included in the package, then you need to purchase them in advance.

After preparing all the necessary materials and tools, you can proceed to active steps and directly to the process of its installation.

Marking the wall for fixing the bowl

Initially, it is required to draw a strip, which will indicate the upper boundary of the washing machine and will act as the main one for all further markings.

Then you need to apply the bowl to the wall, taking into account the fact that a gap must be observed between it and the electrical appliance. Its size depends on the type washbasin siphon. With the correct location of the bowl, it is necessary to mark the holes for the fasteners.

An important nuance is the location of the mixer.If it is used alone in the bathroom and the sink, which happens very often, then you need to make sure that the length of both plumbing fixtures is optimal. In the case of a significant removal of the bowl from the bathroom, it can be placed close to the side.

Bowl mounting

First of all, you should drill all the previously marked holes. The drill used must match the diameter of the anchor. Further, in the hole made, you need to install the anchor bolt.

The next step is to fix the brackets. After that, it is necessary to partially screw in the bolts with gaps of about 0.5-0.7 cm left, which will be required during the further installation of the washbasin.

Next, it is necessary to seal the future joint between the wall and the edge of the sink, for which a silicone-based sealant must be applied behind the bowl. The composition should be at a distance of about 0.5-1 cm from the side. In the same way, the brackets should be processed in those places where they will come into contact with the washbasin. Then you can install the bowl on them.

After that, you need to use the metal hook that comes with the sink and place it in the technological hole, which is located on its back side. You can install it from any edge that is comfortable for you.

At the next stage, using a hook, it is necessary to fix the bowl in place and secure the connection with a dowel or self-tapping screw. Upon completion, it is required to perform the final tightening of the anchor bolts that hold the brackets.

Collection and connection of the siphon

In some cases, it is more comfortable to do this until the anchors are fully fixed.The first step is to assemble the device, strictly adhering to the procedure and recommendations given by the manufacturer in the instructions.

In the course of work, it is imperative to lubricate all threaded connections. Sealing components should be treated with silicone sealant

Plastic elements must be handled with extreme care so as not to damage them with excessive force.

Next, you can proceed to connect the special siphon pipe to the drain hose of the washing machine, which, for persuasiveness, should be fixed with a clamp with a screw tightening. After that, it is necessary to connect the product to the sewer outlet. Experts recommend bending the corrugation with a knee and fixing it with electrical tape or soft wire.

In this case, an auxiliary water seal is formed, which, due to the design features of the siphons of this sink, will not be superfluous, since their water seal is often disrupted and causes an unpleasant odor to enter the room from the sewer. To get rid of this problem allows the bending of the corrugated pipe.

At the final stage, the installation of the mixer should be carried out. Only occasionally is it fixed on the shell. It is mainly installed on the wall. Mounting must be carried out in accordance with the requirements specified by the manufacturer in the instructions.

Next, you need to make sure that the work performed is correct by making a trial inclusion of water. During it, it is required to check all connections for leaks. If there are no shortcomings, then the equipment can be freely used.