Ariston washing machine errors: decoding fault codes + repair tips

Water heating problems

If during the washing mode the washing machine freezes for a long time, stops, does not heat up or constantly drains water, the causes of the breakdown should be sought in the heating circuit. The device will signal these problems with codes F04, F07 or F08.

Failure of the heating element or pressure switch and codes F04, F07

In washing modes that require heating, the error may appear immediately after start-up, or after water is drawn, but rinsing or washing in cold water will work normally. In this case, there are several options for solving the problem (in addition to the standard turn on / off the machine to restart the controller).

If the code appeared on the display at the washing stage or at startup (the machine does not even want to draw water), most likely the reason lies in the heating element itself. It can "punch" on the case when the contacts are separated or simply burn out.

To fix the problem, you need to get to the heating element, check all its connections, change the resistance with a multimeter (at a power of 1800 W it should give out about 25 ohms).

To replace a faulty heating element, disconnect the cable with wires, unscrew the fixing nut (1), press on the pin (2) and pry off the sealing rubber (3), then install a new part and assemble in the reverse order

If the device collects and then immediately drains water, the cause may be a breakdown of the pressure switch - the water level sensor. In the event of a malfunction, this element can provide the controller with information that the heater was not immersed in water, so the machine does not start heating.

In this case, it is necessary to check the tube of the water pressure sensor with the pressure switch (the hose may become clogged, bent, frayed or come off). At the same time, inspect the contacts of the sensor itself - it may be necessary to clean them. But more precisely, code F04 “says” about the breakdown of the pressure switch - most likely, the part will require replacement.

To check the operation of the pressure switch, you need to put on its inlet fitting a small piece of hose with a diameter identical to the removed tube and blow - characteristic clicks will be heard from a serviceable part

In some cases, the problem may be in the board itself, faulty wiring or contact groups in the area from the board to the heater or water level sensor. Therefore, you should ring all the elements of the control unit associated with the operation of the heating circuit, if necessary, replace burnt tracks or the controller itself.

Malfunctions in the heating circuit and symbol F08

If the water heating does not work correctly (or the machine “seems” that it starts when the tank is empty), error code F08 will appear on the display. The most common cause is a malfunction in the pressure switch circuit.

Such a problem may occur due to high humidity in the room, which adversely affects the controller. To make sure that the board is in order, inspect it, wipe it dry or blow it with a hair dryer.

Another simple solution to the problem can be the disconnected contacts of the heating element and the pressure switch, especially if the device was first started after transportation. In other cases, a more professional inspection with possible replacement of parts will be required.

First, make sure that there really is no water in the tank, then remove the back panel of the machine and check the heating element with a tester

Possible malfunctions of Ariston machines, indicated by code F8:

• If the washing mode is interrupted immediately after starting or during the washing phase and the appliance does not heat the water, it is likely that the heating element will need to be replaced.
• If the machine stops after starting, when switching to the rinse mode or does not wring out, it is possible that the contact group of the heating element relay has “sticked” on the controller in the on state. In this case, you can replace the failed elements of the microcircuit and, if necessary, reflash the board.
• If the device “freezes” in various modes (and this can be either washing or rinsing or spinning), the wiring or contacts in the heater circuit may be damaged, or the pressure switch may break, which considers that the machine does not receive enough water.

But if, when checking all the connections of the circuit and separately the pressure switch, the heating element relay and the heating element itself, no damage is detected, the controller will have to be changed.

Samsung washing machine error codes without display

Not all models of the manufacturer's equipment are equipped with a display. You can identify malfunctions in a Samsung brand washing machine by indicators using a decoding table.

Important! The indicator lights up white. Black backlight indicates that the indicator is off

Watch a video about Samsung washing machine errors

Manifestation of code on typewriters without a screen

If the Ariston washing machine is equipped with a display, then there will be no problems with diagnostics - the washing machine will display the code and narrow the search field. It is more difficult with models without screens, since you will have to navigate by the indication, in simple words, by the blinking of the LEDs on the dashboard. The frequency and number of flickering depends on the brand of the machine.

On Ariston Margherita type ALS109X, the F03 error is manifested by the flashing of the two keys on the panel - power and UBL. The bulbs glow in a triple series, after which they go out for 5-10 seconds and light up again. At the same time, the programmer “beeps”: it clicks and rotates clockwise.

Machines of the AVL, AVTL, AVSL and CDE series report the impossibility of heating by indicating the two lower keys responsible for additional options.Their names vary depending on the brand, as a rule, “Extra Rinse” and “Quick Wash” blink, less often the simultaneous blinking of “Spin Speed ​​Reduction” and “Easy Ironing” is less common. The "Key" button is also actively lit, and with a greater frequency.

The Low-End lineup at Hotpoint-Ariston (for example, ARSL, ARXL and AVM) issues F03 through the two lower LEDs “Hatch Lock” (referred to as “Key” on some models) and “End of Cycle” (sometimes there is an option “END "). Additionally, the additional function keys light up, located:

• horizontally (on brands of the Ariston BHWD, BH WM and ARUSL line);
• vertically (washers ARTF, AVC and ECOTF).

Owners of Hotpoint-Ariston machines from the Aqualtis model range can detect the F03 error by flashing the lights indicating the temperature selection. These are "No heating" and "30°".

What error codes "Indesit" exist and what to do?

The main errors issued by Indesit are from F01 to F18, as well as H2O. However, there are exceptions to consider:

• F16 is characteristic exclusively for "washers" with vertical loading,
• F13-15 are not available on Indesit machines that do not have a drying function.

When a breakdown occurs, the code of which is displayed on the display or is recognized by the number of blinks, the door is blocked. Indesit error codes can signal both technical problems and incorrect inputs (exceeding the permissible load limit, for example). The Indesit washing machine can give an error both at startup and during operation (when switching to rinsing or spinning, if a functional discrepancy is found).

Hot water malfunctions (error 2**)

These types of faults occur in dual circuit gas boilers Ariston. For hot water, the security system is autonomous, which allows you to quickly identify the problem.

Many models of Ariston boilers support the ability to connect a solar system as an alternative source energy for hot water supply. Therefore, some errors and warnings of the “2**” series are related to the operation of solar panels.

Error No. 201. Problem with the power supply of the temperature sensor - open or short circuit. It is necessary to eliminate the breakdown of the wiring.

Errors No. 202-205 are related to the operation of sensors. When the signal stops coming from them or it behaves unpredictably (sudden jumps in data), then these errors are triggered:

• No. 202. Problem with the boiler or solar system sensor.
• No. 203. Problem with the NTC temperature sensor.
• No. 204-205. Problem with the temperature sensor that fixes the operating values ​​of the solar collector.

To solve problems Nos. 202-205, you need to check the density of contacts. If it's not them, then you will have to replace the faulty sensor.

Error No. 206. Problem with the cold water temperature sensor in the solar system. The solution is the same as for errors ## 204-205.

The temperature sensor is easier to replace than to clean. They are inexpensive, and it is easy to find them, since parts with standard parameters are installed in the boilers.

Error No. 207. Overheating of the solar collector thermostat. This can be caused when the solar energy is not being used to heat the water. Then the collector must be turned off. Also, this malfunction can occur if the thermostat breaks down. In this case, it will need to be replaced.

Error (warning) No. 208. Insufficient heating in the solar collector circuit. There is a risk of freezing of the coolant. It turns on when the “anti-freeze” function is activated.Part of the energy from the gas will be used to heat the collector.

Error (warning) No. 209. Water overheating in the boiler connected to the boiler. There may be a problem with the thermostat or with its contacts.

Error decoding

What does it mean if the Ariston washing machine gives an F02 error on the display? The reason may be a breakdown of the tachometer. Perhaps a short circuit has occurred or the contacts between the motor and the tachometer have burned out. Subsequently, the drum does not spin, fault code F2 is displayed.

Models of Ariston washing machines differ in control methods. Therefore, error F 2 is issued differently in electronic and electromechanical systems.

A model from the Ariston Margherita series with 2 indicators: the "Network" LED flashes twice with an interval of 5-15 minutes. The LED "Key" - "Lock" is on, the switch clicks, rotates clockwise.

SMA Ariston type AML, AVL, AVSL: the "Quick wash" LED flickers, the "Key" light flashes even more often.

Hotpoint-Ariston washing machine from the ARL, ARSL, ARXL, ARMXXL series: the “Program end” (END) indicator blinks, all program lights (bottom) are on.

Hotpoint-Ariston Aqualtis (AQSL): 30° temperature indicator flashes.

Knowing what the error code means, you can start troubleshooting.

Ariston margarita 2000

The car Margarita 2000 has a stainless steel tank. The bearings are installed in a removable cross mounted on the rear wall of the tank - it does not need to be removed to repair the bearing assembly. Repair sequence:

1. Tighten the transport bolts.
2. Remove the hatch on the back of the device.
3. Unscrew the fixing nut and remove the pulley by prying with two screwdrivers.
4. Remove the top cover, remove the counterweight.
5. Put the machine on the front panel, after removing the door.
6. Unscrew the fasteners of the removable cross of the tank.
7. With gentle blows, remove the cross from the shaft.
8. Remove the oil seal and bearings from the cross. Replace, lubricate and reinstall.
9. Put the crosspiece on the shaft and fit the bearings with gentle blows with a rubber mallet.
10. Fasten the cross and pulley, put on the belt.
11. Place the machine vertically and check the smooth rotation of the shaft.
12. Install the front door, top cover and rear hatch.

Do-it-yourself repair of the Ariston Margarita 2000 washing machine is completed.

Repair features AVTF 104

Top loading washing machines such as the AVTF 104 have a number of features:

1. If water accumulates under the bottom of the machine, not only the tank and various connections can leak, but also the seal at the top.
2. Imbalance of the unit can lead to spontaneous opening of the hatch doors. As a result, the heating element can be knocked down, the doors themselves are broken, the tank is damaged.
3. Vertical machines are distinguished from frontal models by the principle of fastening the drum, which is supported on two axle shafts equipped with two bearings. Accordingly, to replace them, it is necessary to remove not the rear of the unit, but the side panels.

It is worth considering that top-loading models are made in Europe, therefore, replacement parts for them are more expensive and less common.

The source of the error has been found - how to fix it?

We will warn you right away that absolutely all the causes of the f05 error cannot be eliminated on your own. Nevertheless, in most cases, you can do without extra costs and calling a specialist. The easiest way is to clean the filters, hoses and sewer pipe from blockages.The drain hose can be flushed with a powerful jet of hot water, and the sewer pipe can be cleaned with a liquid pipe cleaner or a long steel wire.

The situation is more complicated with the sensors of the pressure switch and the drain pump. In order to check the voltage on them, elementary skills in working with a multimeter are required. In addition, you must first study the table, which provides information about the voltage supplied to specific nodes, a specific model of the Ariston washing machine. And then check these nodes one by one with a multimeter and compare the resulting values ​​\u200b\u200bwith the data in the table.

There is a high probability that you will not want to do such things, or you will simply be afraid to climb into the "insides" of the machine. In this case, do not rack your brains, contact a specialist who will quickly solve the problem with system error f05. Good luck with your repair!

Signs of breakdown and repair

Before you start solving the problem, it is worth accurately diagnosing the problem that has arisen. If among the signs of a breakdown a door that does not close, a lock disappears in the middle of a cycle, or a hatch that does not open at the end of the program, then UBL is to blame for 75%. As already noted, it is responsible for achieving tightness in the drum and a locked door. The device cannot be repaired - only a full replacement.

Another failure option is a faulty control module. The control board coordinates the operation of the machine, reads and transmits commands from one element to another. When the electronic controller starts to slow down, the relationship is broken and the system generates an error. The cause will be the burnout of resistors, LEDs, triacs or varistors.

Often other problems are to blame for the display of "F17" or "door":

• oxidized or burnt contacts on radio elements;
• failures in the firmware of the control board;
• faulty electronic controller processor.

Among the reasons may be worn out electric brushes on the collector motor. On many Hotpoint Ariston models, the board controls the operation of the UBL through monitoring the circuit, which includes the engine. If breakdowns are fixed on the engine, for example, wear of carbon brushes, then the system often interprets it as problems with blocking the hatch. It is logical that for repair it is necessary to carry out a replacement.

If it is impossible to close the hatch tightly due to the door tongue not falling into the opening of the body or the absence of a click, we act differently

First of all, we pay attention to two points

• Door hinges. The door is probably warped and cannot fit into the factory grooves. The cause of loose clamps is mechanical action, for example, when children ride on an open hatch. To continue washing, you will need to replace one or two holders.
• Locking mechanism. Both natural sagging and mechanical shock can break the tongue. As a result, the tongue does not fall into the groove. Dismantling the hatch and replacing damaged parts will help solve the problem.

The last reason leading to "F17" or "door" is damage to the wiring in the section from the module to the UBL. Speaking signs will be a refusal to activate the lock, its disappearance during the washing process, the display of an error on the spin or drain. Leading to such troubles is the erasing of the conductor on the sharp edge of the drum or damage to the insulation by rodents. It is safer and more reliable to contact professional repairmen. If it is decided to act alone, then we avoid twists and loose connections.

How to make your washing machine last longer?

Naturally, every person, buying new equipment, wants its service life to be as long as possible, and there were no malfunctions at all. This is completely normal. That's the only reason most people don't do anything.

It is important to realize that in 99% of all breakdowns of the washing machine, the owner himself is primarily to blame. For maximum protection against such troubles, you must adhere to a few simple rules:

• When choosing Ariston (Ariston), it is necessary to study the registration certificate in detail. To understand in which cases the manufacturer's warranty is valid.
• Installation of equipment should be done by professionals. This minimizes possible malfunctions. Do not install hoses and drains yourself. This will void the manufacturer's warranty.
• Compliance with the rules of washing. If the instructions indicate that no more than 6 kg of things must be loaded at a time, this does not mean that 6.5 kg falls under this category.
• The right choice of powder.

Troubleshooting

The Hotpoint-Ariston washing machine, whose service life has not exceeded 5 years, should work properly. If during operation breakdowns are noticed, then it is necessary first of all to determine their causes. So, consumers most often notice problems with the drain pump, which quickly becomes clogged with various debris (thread, animal hair and hair). Much less often, the machine makes noise, does not pump water or does not wash at all.

Error codes

Most Ariston washing machines have a modern self-diagnosis function, thanks to which the system, after detecting a breakdown, sends a message to the display in the form of a specific code. By deciphering such a code, you can easily find the cause of the malfunction yourself.

• F1. Indicates a problem with the motor drives. You can solve them by replacing the controllers after checking all the contacts.
• F2. Indicates that the electronic controller of the machine is not receiving a signal. Repair in this case is carried out by replacing the engine. But before that, you should additionally check the fastening of all parts between the motor and the controller.
• F3. Confirms a malfunction of the sensors that are responsible for the temperature indicators in the car. If the sensors are all right with electrical resistance, and such an error does not disappear from the display, then they will have to be replaced.
• F4. Indicates a problem in the functionality of the sensor responsible for controlling the volume of water. This is often due to a poor connection between the controllers and the sensor.
• F05. Indicates a breakdown of the pump, with which the water is drained. When such an error occurs, you must first check the pump for clogging and the presence of voltage in it.
• F06. It appears on the display when an error occurs in the operation of the buttons of the machine. In this case, the entire control panel must be replaced.
• F07. Indicates that the heating element of the machine is not immersed in water. First you need to check the connections of the heating element, the controller and the sensor, which is responsible for controlling the volume of water. As a rule, the repair requires the replacement of parts.
• F08.Confirms sticking of the heater relay or possible problems with the functionality of the controllers. New elements of the mechanism are being installed.
• F09. Indicates failures in the system associated with the non-volatility of the memory. In this case, the firmware of the microcircuits is carried out.
• F10. Indicates that the controller responsible for the volume of water has stopped sending signals. It is necessary to completely replace the damaged part.
• F11. Appears on the display when the drain pump stops beeping.
• F12. Indicates that the connection between the display module and the sensor is broken.
• F13. Occurs when there is a malfunction in the mode responsible for the drying process.
• F14. Indicates that drying is not possible after selecting the appropriate mode.
• F15. Appears when the dryer is not turned off.
• F16. Indicates the open hatch of the car. In this case, it is necessary to diagnose the hatch locks and mains voltage.
• F18. Occurs on all Ariston models when the microprocessor has failed.
• F20. Most often appears on the display of the machine after several minutes of operation in one of the washing modes. This indicates problems with water filling, which may be caused by malfunctions in the control system, low pressure and lack of water supply to the tank.

Signal indication on a machine without a display

Hotpoint-Ariston washing machines that do not have a screen signal malfunctions in various ways. As a rule, most of these machines are equipped only with indicators: a hatch closing signal and a power lamp. The door lock LED, which looks like a key or a lock, lights up constantly. When the appropriate washing mode is selected, the programmer rotates in a circle, making characteristic clicks.In some models of Ariston machines, each washing mode (“extra rinse”, “delayed start timer” and “express wash”) is confirmed by the lighting of the light with the simultaneous flashing of the UBL LED.

There are also machines in which the “key” door closing LED, the “spin” indication and the “program end” lamp flash. In addition, Hotpoint-Ariston washing machines that do not have a digital display are able to notify the user of errors by flashing water temperature indicators of 30 and 50 degrees.

Conclusions on the topic

If you are good at repairing household appliances and are going to troubleshoot the dishwasher with your own hands, then you should give it a try. True, there is a sure way to avoid such troubles - compliance with operational rules.

The Ariston Hotpoint dishwasher is a faithful assistant, which, with proper care and proper operation, serves without problems and breakdowns for many years. However, if you still encounter a problem with the electronics or control module, it is better to immediately contact a qualified craftsman, without wasting time on independent experiments with the repair of equipment.

Want to talk about how the dishwasher code system helped you identify the cause of a malfunction in a timely manner? Do you have information worth sharing with site visitors? Please write comments in the block below, publish photos on the topic of the article, ask questions.