How to fix a blockage in the bathroom - 3 ways to solve the problem + prevention work

Effective methods for clearing sewer blockages

A plunger is a rubber-tipped stick shaped like a large suction cup that can suck or push debris.

Using this simple invention, you can get the following results:

1. Prevent blockages.
2. Eliminate the causes of slow water drainage.
3. Assess the extent of pollution.

Recommendations for the use of a plunger:

1. Install the device so that its rubber part blocks the drain hole.
2. Draw a small amount of water into the bath (dry efficiency is reduced).
3. Make a few strokes by moving the handle up and down.
4. Check if the water is running out.
5. Flush out the trash.

If this did not help and the blockage in the bathroom did not disappear, then what to do? Use rope:

1. Insert it into the drain hole.
2. Push forward into the pipes and scroll at the same time.
3. When the voltage drops (the blockage is cleared), gently move the cable back and forth.
4. Remove and wash the product.

Chemicals

The modern chemical industry has taken care to make the process of removing blockages as fast and comfortable as possible.

Manufacturers vied with each other to produce tools for cleaning pipes from debris and deposits. The form of release can be varied:

• powder;
• gel;
• liquid.

The most common and inexpensive remedy is Mole - a domestic drug that perfectly eliminates odors, food debris and fat, and also breaks down fibers (hair, wool, etc.). Produced by different companies and may vary slightly:

• by composition;
• price;
• action time.

Compatibility with the type of pipes is usually indicated on the packaging. Here is a far from complete list of effective drugs:

1. Mister Muscle.
2. Bugs.
3. Pothan.
4. Tiret.
5. Flup.
6. Mole.

Folk way to clean the blockage: soda and vinegar

If there is no plumbing, no plunger, no cable, no purchased funds at hand and the bath is clogged, it is worth trying the folk method. This will require:

• ½ cup baking soda;
• ½ cup of vinegar;
• 1 liter of boiling water.

Follow these instructions:

1. Wipe the tub and metal drain ring dry.
2. Pour baking soda into the drain hole.
3. Pour vinegar into it.
4. Pour in boiling water after 1 minute.
5. After 2-3 minutes, turn on the water - it should flow freely.

Siphon cleaning

If, nevertheless, there is confidence that a necessary or valuable thing has become the reason for the slow draining of water, it is worth learning how to clean the siphon in the bathroom. Thus, it will be possible to remove what got into the drain and caused a blockage.

Siphon cleaning technology:

1. Lay a cloth under the siphon, put a basin or bucket.
2. Slowly unscrew the lock nut so that liquid does not rush out.
3. Remove the flask and discard the dirty water.
4. Remove any debris, small parts, or clods that are causing the problem.
5. Rinse the siphon and remove plaque.
6. Install the siphon.
7. Check tightness of connections.

Now, in case the bath is suddenly clogged, you will know what to do.

It is also worth watching a video on this topic:

The first option is to use boiling water

The first way to get rid of blockage is boiling water. However, this method and all others that use boiling water can be used if the toilet is connected to the riser with a plastic or metal pipe. If a corrugated pipe made of thin plastic is used to connect the toilet, then hot water should be used instead of boiling water.

• For cleaning, you will need a bucket of boiling water. It must be poured as quickly as possible not onto the walls of the toilet bowl, but into its hole, so that boiling water immediately enters the knee canal.
• After pouring water, you must wait 30 ÷ 35 minutes.

With a recent blockage of the toilet bowl, a bucket of boiling water often helps to cope. But this method is not always acceptable!

If the boiling water worked, and the water began to leave, then after leaving it, the procedure must be repeated. And so - until the normal function of the toilet bowl is restored.

Chemicals

In some cases, it is appropriate to use chemicals if the tub or sink is clogged. A large amount of chemicals are sold in stores in the form of a gel, powder, liquid or foam, which can remove everything bad that is stuck in the pipeline in a few minutes. Organic contaminants are ideal for chemical removal.

Recommendations:

1. Be sure to read the instructions included with the kit before use.
2. Use personal protective equipment to avoid unwanted consequences.
3. Buy products that dissolve the hairline.

Folk method number 1: boiling water

Folk methods are no less popular and give good results. But, alas, removing a strong blockage in the sink or bath with the help of them is impossible. If pipes or drains have accumulated a large amount of fat, then this can be corrected with boiling water. Just pour boiling water into the hole until the water begins to flow better.

Folk method number 2: vinegar and soda

Baking soda and vinegar react with each other, so they can remove more difficult pipe stains. At the very beginning, soda is poured into a glass, after which it is sent straight to the drain. Next, pour vinegar into a glass and pour it down the drain and plug it with a cork. Foam will begin to form if the vinegar and soda react. After 15-20 minutes, rinse with hot water to wash off the remaining vinegar and soda.

Folk method number 3: lemon

Folk remedies are beneficial and convenient to use at home, but they do not always give the desired effect.But lemon will help get rid of light pipe contamination. Squeeze the juice from one fruit down the drain and wait an hour or two. As time passes, the sink or tub is rinsed with hot water.

Wire drain cleaning

To clean the sewer system, you need a wire 5-6 mm in diameter. It is used, as well as a cable, there are only 3 differences:

1. The wire does not bend well and hardly penetrates through the turns of the pipes. If there is no tee or revision, then you will have to disassemble the connection or, in extreme cases, punch a temporary hole in the pipe. When the pipe is clean, the hole is wrapped with a cut camera from a bicycle or a rubber bandage. A clamp is installed on top of this winding;
2. The blockage must be cleaned from top to bottom, otherwise several meters of the collected sewage will immediately pour out on you;
3. It is necessary to rotate the wire when removing, so the hooked rag does not come off.

Human hair and animal hair are removed from the pipe with a wire or cable. Hair is removed from under the outlet grate in 2 ways:

• Hooking them with a wire hook;
• Disassemble and clean the grate.

Cat litter or construction debris is removed with a wire brush or cable.

Mechanical ways to eliminate blockages

If you want to eliminate the blockage in the sewer system after foreign objects get into it, a good result in solving the problem of how to clean the toilet can be provided by mechanical methods carried out:

• using a plunger;
• with the help of the so-called "doll";
• using a cable;
• with film.

Their main advantage is ease of implementation.

Cleaning with a plunger is used in case of slight blockage. The device should have a cone-shaped nozzle with a diameter of 10 centimeters.

The work is done like this:

1. The toilet is filled with water.
2. The plunger is placed in the drain hole and, holding it by the handle, make several clicks.
3. With a sharp movement, the device is removed from the drain hole. This procedure can be repeated several times.

If there is no such product in the house, you can use a standard plastic bottle with a cut off bottom - it is used in the same way as a plunger.

The use of the so-called "doll" is another way to clean the toilet. A homemade object is made from a fabric bag, which is filled with sand and supplied with a long rope.

"Doll" is used as follows:

1. She is placed in the plumbing drain hole, holding the rope in her hands.
2. They press the drain and wait for the water flow to carry the bag along with it.
3. Then it is removed from the toilet using a rope.
4. Due to its weight, the sandbag eliminates the blockage formed in the water seal.

There is a way to clean the toilet with a cable at home. This flexible sanitary ware is distinguished by the presence of a hollow rigid axis and a handle. The handle allows the rope to rotate. At the end of the axis there is a spiral process, which is attached to the cable with a flexible tube.

If you need to implement a method on how to clean the toilet with a cable, do this:

1. Lower the end of the tool into the drain hole of the device until it stops.
2. Performing rotational movements with the handle of the device, slowly push the cable into the water seal.
3. When the process of eliminating the blockage is eliminated, the drain system is washed with hot water.

You can also use another method than to eliminate the blockage in the toilet, which consists in the use of a film.To remove objects that have fallen into it from the plumbing device, in this case, you will need a wide adhesive tape.

When using it, proceed as follows:

1. Wipe the toilet seat dry.
2. Strips of adhesive tape are glued to the circle, connecting them together so tightly that a continuous film coating is formed.
3. When the device is completely hermetically sealed, drain the water in it.
4. After performing a few strong hand pressures on the cover created from adhesive tape, the resulting blockage will be broken.
5. After completion of work, the film is removed from the seat.

Why is the toilet clogged

If the toilet is clogged, it is important to immediately deal with the problem. This will help to avoid the most unpleasant consequences.

The following unpleasant factors can lead to blockage:

• foreign objects (rags, children's toys, personal hygiene items);
• incorrect installation of the structure;
• damage in one of the sections in the sewer system;
• there is no valve that regulates the pressure in the sewer pipe;
• the cause of blockages is sometimes associated with defects in the toilet itself;
• salt deposits that accumulate on the inner surface of the pipes.

Poor installation of the sewer system causes many problems. There may be an accumulation of water in a certain section of the pipe due to its sagging. Bad fastenings lead to freezing of pipes.

Nothing but toilet paper should be thrown into the toilet. It is not recommended to pour grease from dishes, food leftovers, tea leaves, construction waste into the toilet bowl. It is all the more dangerous to throw any items of clothing or personal hygiene into the toilet.

When a blockage occurs

To begin with, it would be nice to figure out what can lead to the formation of a blockage in the drain of this container.As a rule, keeping track of what goes into the drain along with water can be difficult. Often the cause of the slowdown in the descent of water is:

• various small rubbish;
• hair;
• pet hair.

Gradually accumulating in the pipe, all this is compressed, resulting in a dense lump of debris that begins to interfere with the drainage of water.

Clogged sewer pipes

And if at first the water from the bath, although very slowly, but merges, then at one fine moment it stops leaving at all.

Blockage definition. Cleaning with baking soda and vinegar

Most often, pipes become clogged in the summer. At this time, people use water much more and can, without thinking, throw cleaning products into the drain. If an unpleasant odor appears near the drain, this is already the first sign of a blockage. The most reliable is the rate of runoff of water. If it has decreased only slightly, the problem may be small and the pipe will be easy to clean, but a puddle in the sink indicates that you will have to suffer. If the water begins to return through the drain and at the same time it is dirty, has a pungent odor, it is urgent to begin to act.

A good way to clean the drain and remove blockages is to use baking soda with vinegar. You need to take one glass of these substances. Soda is the first to be poured into the pipe, immediately after it comes vinegar. Since the components are acid and alkali, they will immediately react. After that, it is advised to close the drain with a cork or a rag and leave it for several hours. After that, you need to rinse the pipe with hot water - and the blockage is gone. If you are wondering how you can protect your hands, take any thick gloves that are sold in supermarkets.

Preventive measures

Without a doubt, the best way to deal with blockages is preventive measures.Careful operation, at least, will allow less frequent use of cleaning agents and forced cleaning of pipes.

What to look out for

Do not throw foreign objects into the drain. Moreover, this category also includes toilet paper, handkerchiefs, cotton buds, and, of course, personal hygiene products. Just equip the toilet with a trash can with a lid.
If you notice something in the drain, such as a freshener that has come off the rim, try to remove it immediately. Don't expect to be able to just wash off the plastic. Most likely, it will get stuck somewhere in the pipe and give you drain problems.
Some housewives pour leftover food, whether liquid or even second courses, into the toilet.

By no means should this be done! Fat and solid waste gradually form a dense layer, which you will later spend a lot of time and effort to remove.
If there are small children in the house, watch them, teach the rules for the careful use of plumbing so that the baby does not throw felt-tip pens, books and other toys into the drains.
Special situation: renovation. To prevent construction dust, sand and concrete from clogging the ducts, be sure to cover the pieces of furniture with a film.
Periodically clean the drain with disinfectants and solvents, carry out preventive maintenance

But when working with them, carefully follow the instructions so as not to damage the pipes.
Wash the toilet itself weekly: inside and out.
Old pipes get clogged more often than new ones, because much more debris accumulates on a loose surface. Replacing pipes sometimes becomes the only possible and correct solution in the fight against clogged drains.

Cleaning an old faucet

When there is an old faucet in the apartment, many people face the question of how to clear the blockage in the sink. The main cause of this problem is the accumulation of rust. The aerator is also often clogged. This leads to the fact that the water in the bathroom does not drain well. To prevent this, you need:

• turn off the water with valves;
• open the taps to check the flow of water;
• dismantle the aerator using an adjustable wrench;
• rinse the nozzles or clean them with a needle;
• set the item in place.

When tightening the parts of the crane, you should not use great effort, otherwise you can break the thread.

No need to wait until a blockage appears in the bathroom, everyone should know how to clean it with chemicals. They are great for prevention as well. To do this, pour a small amount of gel into the drain for a couple of minutes, and then rinse the hole thoroughly with hot water.

Folk remedies

You can also eliminate blockages in the bathroom with folk methods. The most popular means for these purposes is soda and vinegar.

To clear blockages:

1. Place half a pack of soda in the drain hole and leave for five minutes. After that, rinse with plenty of water.
2. Place 4 tablespoons of soda and half a glass of vinegar into the drain. After that, the hole is closed so that nothing interferes with the chemical reaction. After a few minutes, hot water is turned on.

During the use of these recipes, it is better to wash off the remaining debris with strong pressure. These methods of struggle are no less effective than mechanical and chemical methods, but they can degrade the quality of pipes.

How to dissolve blockage

Unlike solid objects (jewelry, toys and their parts, toothpicks or cotton swabs, etc.)etc.) hair in the bathroom drain can be dissolved. For this, both industrial and some folk remedies are suitable.

industrial facility

A lot of products are produced from blockages, but it is better to choose one that says "dissolves hair and wool." Also read the instructions: not all chemicals are suitable for use in a certain type of sewer pipe. For example, aggressive "Mole" is not recommended for plastic.

Cleaners are liquid (gels) and dry (powders). The latter type is combined with a small amount of water, and usually it shows more efficiency.

Remember to wear protective gloves and ventilate the bathroom after using chemical products.

soda and vinegar

If there is no time to run to the hardware store for professional products, use what is always at hand. Ordinary soda and vinegar do an excellent job with various dirt and blockages.

How to remove blockage with the folk method:

1. If there is water in the bathroom that does not go through the pipe, bail it out.
2. Now pour about half a pack of baking soda down the drain.
3. After a couple of minutes, turn on the hot water faucet. The soda will sizzle and go deeper into the pipe.
4. Instead of water, you can pour a glass of table vinegar. A violent reaction will begin, which will clear the blockage. After the hissing stops, turn on the hot water.

Tip from Miss Clean magazine: Consider why the drain gets clogged with hair quickly. Check your health if your hair is shedding a lot. Also, when washing your hair, do not scrub the skin, do not pull out the hair, use mild shampoos and conditioners.

6 ways to clean the sewer

Home remedies to deal with blockages in sewer pipes are effective if you follow the instructions for using vinegar and baking soda.

There are several ways to clean plugs:

1. Method 1. Drain the water from the sink and remove all debris. The action of the mixture of soda and vinegar should take place directly in the pipe. First, powder is poured into it, after which acid is immediately poured. Warm up the vinegar. The drain hole is tightly closed with a rag or a special plug. It prevents the resulting foam from escaping back into the sink. Under the influence of a violent reaction, the fat begins to dissolve, and the dirt moves away from the walls of the pipes. Do not open the drain hole for 40 minutes. After cleaning is completed, the pipeline is washed with hot water.
2. Method 2. Here, boiled water is first poured into the drain. It helps soften the fatty plug. Next, the prepared mixture of heated vinegar and soda is introduced into the pipe. The duration of this cleaning is 2 hours. All this time, the drain hole remains closed.
3. Method 3. Boiling water is combined with soda powder and injected into the pipe. After 10 minutes, acetic acid is poured into it. Further, all actions are carried out in the same order as in the previous instructions. Cleaning is carried out after 2 hours. If there is no effect from the first time, the procedure is repeated. Additionally, it is fashionable to use a plunger.
4. Method 4. That requires two types of soda in equal amounts - calcined and food. The mixture is poured into the drain as deep as possible. Leave it there for 40 minutes. Part of the acetic acid is applied to the device itself, and the rest is poured into the drain. After half an hour, the toilet bowl or sink is washed with hot water.
5. Method 5.In this case, caustic soda is used. It is sold in powder or gel form. Requires 2-3 tbsp. mix the substances well and put them into the drain. Further, 1 tablespoon is poured into the pipe. boiling water, and the hole closes. After 2 hours, the drain pipe is flushed with boiled water. Wash all enamel parts thoroughly from caustic soda, as it can corrode the material.
6. Method 6. In equal quantities (half a glass), soda and salt are combined. The composition is poured into the drain pipe. After that, the mixture is poured with acetic acid. Seal the drain hole. After 2 hours, the pipe is washed with hot water.

A good effect for cleaning is a mixture of soda and salt. It will clean greasy deposits on the walls of pipes well. Both components are mixed in equal proportions and poured into the pipe. After an hour, it can be washed with plenty of hot water.

The blockage in the toilet can be cleaned in this way: first, pour a pack of soda into it, drain the liquid and wait at least 60 minutes. After that, another half pack of powder is poured into it, but now it is mixed with 2 cups of acetic acid. To improve the effect close the toilet lid. It is recommended to carry out such cleaning 2-3 times a year.

Reasons for the appearance

There can be several reasons for water pollution. First you need to understand whether it concerns only your apartment or the entire sewer riser. In the first case, you can fix the problem yourself, but in the second you need to call a specialist.

To determine the degree of blockage, turn on water from taps that are not connected to the same drain system. For example, in the bathroom and in the kitchen.If there is no problem in one of the sinks, then you are dealing with local pollution, which you can eliminate yourself.

Why blockage occurs:

• Oily coating from food residues.
• Incorrect pipe slope during installation.
• Old sewer system.
• Adhering particles of debris and hair.
• Lumps of pet hair.

If you don’t know how to clear a blockage in the bathroom, then you can call a plumber. But there are times when there is no time to wait for his arrival, and you need to save yourself on your own.

Proven options with instructions

There are several methods of using soda solutions in the fight against blockages. The composition of the cleaning agent is prepared depending on the nature of the substances that formed the mud plug, as well as on its density.

An important role in the proportional ratio of components is played by the material from which the sewer pipes are made. It is also necessary to take into account the degree of wear of waste equipment.

Soda with vinegar in different proportions

To eliminate the mud plug you will need:

• 150 g sodium hydrochloride (soda ash);
• 100 g table vinegar.

Sequencing:

Wear gloves, an apron and goggles.
Pour baking soda into the drain hole in a thin stream.
Then carefully add the vinegar.
Plug the hole immediately.
Boil 5 liters of water.
After 1-1.5 hours after the start of the chemical reaction, pour boiling water into the drain.

To remove a dense blockage, a more concentrated solution is prepared. To do this, mix half a pack of baking soda with 100 g of acetic acid. Quickly pour the mixture into the drain and close the hole with a stopper. Using concentrated acid instead of table vinegar, you can provide a more intense release of carbon dioxide.

But it must be remembered that with the help of soda and vinegar, only those mud plugs that are near the drain can be removed. In the fight against remote blockages, more radical methods must be used.

Using Whiteness with Vinegar and Baking Soda

The active substance of "Whiteness" is sodium hypochlorite, which has a powerful antiseptic and antimicrobial effect. But it is impossible to mix this remedy, which includes active chlorine, with a solution of soda and vinegar.

It is better to first clean the blockage with a soda-vinegar solution, then after 1.5 hours, rinse the drain with a pressure of hot water. And only after 12 hours, 1 liter of "Whiteness" can be poured into the drain hole.

Do not use the bathroom for about two hours. During this time, the product will dissolve the remnants of greasy plaque and eliminate the unpleasant odor. Next, the drain must be washed with five liters of hot water.

Caustic soda

You can use caustic soda to clean the blockage only if the sewer pipes are made of metal. All other materials may be damaged. The exposure time should not exceed three hours.

Caustic soda can be in the form of a powder or granules. Some sanitary cleaners sell caustic soda in liquid form.

Prepare a solution from powder to remove blockages as follows:

• prepare a galvanized bucket with a volume of 10 liters;
• pour 2 kg of caustic soda into it;
• pour the powder with seven liters of cold water;
• mix with a wooden or metal stick until the sodium is completely dissolved.

The chemical reaction of the interaction of caustic soda with water is accompanied by an increase in temperature to 60ºС.

Mode of application:

1. Send the prepared solution to the drain hole.
2. Close the drain tightly with a stopper.
3. Wait 3 hours.
4. Direct a stream of cold water into the drain, hold for 15 minutes.

In a private house, cleaning with caustic soda is recommended to be carried out 2 times in a row. To achieve a greater effect, dry caustic soda can be immediately poured into the drain hole without dissolving in water.

First you need to warm up the pipes. To do this, send 3 liters of boiling water to the drain and wait 10 minutes. Then pour 6-7 tbsp. granulated caustic soda. It is necessary to ensure that the substance does not wake up on the surface of the bath. If the powder does get on the enamel, it must be removed immediately with a wet cloth.

Then a glass of warm water must be poured into the pipe. In order for the caustic to dissolve the blockage, it will take at least three hours. Then rinse the drain with clean water. It is necessary to work with caustic soda only in protective clothing (apron, gloves, goggles).

Before the procedure, be sure to open the windows and doors to the bathroom and turn on the ventilation. If the solution comes into contact with the skin, immediately rinse the body area with plenty of clean water.

Tips & Tricks

In order not to have to think about how to get rid of strong pollution, one must not forget about preventive measures. Prevention should be regular. It is also worth assessing the condition of the sewer pipes, because the reason for the frequent occurrence of pollution may lie precisely in this. If the pipes are in very poor condition, even regular maintenance will not help. They need to be replaced.

It is advisable to remove them from the drain after each shampooing.This can be done with rubber gloves.

Regular preventive maintenance will allow you to avoid spending a lot of time on cardinal cleaning. You can clean the sewer not weekly, but monthly. If the drain hole becomes clogged very quickly, preventive cleaning is carried out more often.

For information on how to eliminate blockages in the bathroom, see the following video.

Siphon cleaning

When the bath is clogged in a certain place, then, as a rule, the plug is located in the siphon. But before unscrewing it, you should definitely substitute some kind of container under it. After that, you need to take the following actions:

1. The nut is unscrewed, which clamps the tube in the siphon.
2. The tube is pulled out and lowered into a basin for cleaning, the dirt is removed with a brush.
3. A solution of soda and vinegar is poured into the pipe, which is connected to the sewer.
4. The procedure with the infusion of vinegar should be repeated as long as the hiss lasts.
5. To complete, hot water is poured into the pipe, about 3 liters, but not boiling water.
6. The curved tube is held in place with a nut.

If there is no cork in the pipe, then in this case a solution of soda and vinegar is not needed.

Mechanical ways to clean the sewer

These methods are among the most cardinal and effective. When chemical-thermal methods have exhausted themselves and have not brought the desired effect, they turn to mechanical methods for help and use them to remove blockages in pipes at home.

Siphon cleaning

If the cause of the blockage is in the immediate vicinity of the place where the water drains, then it is much easier to disassemble the siphon and rinse it thoroughly under running hot water. The siphon performs the function of a hydro-barrier, preventing the ingress of unpleasant odors from the sewer into the apartment.Therefore, the appearance of an unattractive amber, combined with a difficult outflow of water, indicates that it was the siphon that was clogged.

Using a plunger

This French word is called the simplest hand-held plumbing tool, consisting of a rubber valve and a wooden handle. The principle of operation of a plunger is similar to that of a pump. The drain hole is closed with a rubber valve, and then the water flow is injected with reciprocating movements, first in one direction, then in the opposite direction. For more efficient operation, it is necessary to plug the emergency drain hole with the help of improvised means (for example, a wine cork). The plunger is effective if the blockage is located near the drain hole, usually in the siphon.

Plumbing cable

A special flexible cable is made of metal and consists of an outer sheath, inside which the cable itself is located. At one end of this device there is a special handle for rotation, at the opposite end there are hooks and grippers, with which the blockage is cleared. The cable is used to clean places located much further than the siphon, so it is better to remove the latter before starting work, since its bends and knees will not make it possible to push the cable to the desired depth. The cable is rotated clockwise, as rotation in the opposite direction can damage its sheath.

It just so happened in our family that we always buy Mole to eliminate blockages in the sewer. We've been using this product for as long as I can remember. Most often for prevention purposes. If something is serious, then the husband uses a special flexible cable.With it, you can extract a whole bunch of any, excuse me, garbage from the sewer pipe.

Nadezhda, 28 years old

As a person with a higher education, I once graduated from MEPhI with honors, but for the past few years I have been forced to work as a plumber, I can say the following. Do not attempt to clear any major blockage in the sewer system yourself. It won't lead to anything good, but it's easy to do bad things. Call immediately professionals who have more experience and the necessary tools are available.

Nikolai Alexandrovich, 40 years old

I don't believe in all these modern chemists. They will write anyone, but in fact the bleach is solid, there is nothing to breathe. Another thing is the old grandfather's way, which my mother taught me, the kingdom of heaven to her. We take soda ash and pour it into the hole, and therefore pour five liters of steep boiling water there. And that's it, no smell to you, no stink, and the sewerage is as good as new.

Zinaida Sergeevna, 65 years old

Originally posted 2018-03-03 06:29:28.

Mechanical cleaning with a rope

What to do in a situation where boiling water in combination with a plunger cannot cope with blockages in the sewer? In this case, the surest way would be a cable. Care should be taken, since such a device can easily damage plastic pipes, and they will leak.

To make a cable yourself, you will need a metal flexible wire. Then one end of the cable must be bent to make a small hook. It will be convenient for them to cling to the debris stuck in the drain hole and pull it out. As for the second end, then a piece of fabric should be wound to it, making a handle.

It is necessary to carefully shove the cable inside the drain pipe and try to push through the accumulated dirt. In order for cleaning to be better, you can turn the device clockwise. Then you need to pull out the cable with the remaining debris.

To wash off the blockage completely, it is necessary to flush the drain with a strong stream of boiling water from the shower or faucet. This method is one of the most effective to date. This is what most plumbers use.

Cable

A plumbing cable is a thick twisted wire coiled into a small spiral. For convenient rotation, a handle with a wooden or plastic nozzle is provided at the end.

Such a device is actively used to remove sewer blockages. And we are talking mainly about metal pipes.

Application:

The end of the cable must be carefully inserted into the drain hole.

It is best to do the work together. So, one person slowly rotates the handle, while the other gently pushes the cable forward.

When the cable is twisted, accumulated debris is removed from the pipes, that is, the blockage is destroyed.

As soon as the voltage in the pipes decreases, you need to pull a few times cable back and forth.

The cable is carefully removed, washed and stored.

If the procedure was ineffective, it is repeated.