How to clean the toilet yourself: the best ways to clear blockages

How to eliminate in the sink?

The drain in the sink gets clogged especially often. To get rid of blockage, proceed as follows:

1. Plug the drain and fill the sink with hot water.
2. Rub the laundry soap on a grater and pour it into the water.Stir the chips until completely dissolved.
3. Remove the plug, drain the water. Apply table vinegar to the sponge. Rub it on the walls of the sink. This method allows you to cope with dark spots and give the surface a shine. A little acid can be poured into the drain. This is done to disinfect it and get rid of an unpleasant odor.
4. Lime deposits can be removed with baking soda. She rubs the areas on which the dishes and other kitchen utensils are located. The powder is distributed over a damp surface, left for half an hour, the sink is treated with a brush.

If the layer of limescale is dense and old, the sink is pre-moistened not with water, but with vinegar, after which baking soda is applied to the problem area. The exposure time of substances is increased to 60 minutes.

How to remove a blockage in the sink with soda and vinegar, the video will tell:

Mechanical methods

We have already talked about the plunger. It can also be used for clogged sewer pipes. It is also desirable to warm up the contents of the pipes beforehand, pour at least the same soda solution, and then “pump” all this with a plunger. Such a comprehensive measure can clean the sewer even with a serious plug.

How to work with a rope

If a rag, a tuft of hair, or something similar is stuck in the pipe, none of the above methods will work. You will need a special plumbing cable. This is a cable (or flexible steel wire) with a handle on one end and a hook, brush or spiral on the other.

This is what a plumbing cable looks like. At home, it can be replaced by ordinary unannealed wire (flexible)

Some cables may have a replaceable nozzle, simpler ones end in one device.The handle is made in such a way that the handle remains stationary, and the cable inside turns.

Using a plumbing cable is not difficult, but it is better to work with an assistant. Put on gloves, dirty clothes and start cleaning the sewer. First, provide access to the sewer pipe. You can remove one of the siphons, and in a private house it is better to provide such a backup point for cleaning sewer pipes when planning a sewer.

The principle of "working with a cable" with a spiral or hook and at the end is to hook the cork that clogged the pipe and pull it out. It is unlikely that it will be possible to pull out the whole thing at one time, but in parts it is real.

How to work with a plumbing cable

The cable is unwound, the end is launched into the pipe, they begin to rotate in one direction. The second person at this time pushes the cable through the pipe. If the cable is stuck in some area, you can pull it back a little, then try to push it again (we continue to rotate the handle). This is either another turn of the sewer, into which the end of the cable rested, or a blockage. A couple of times trying to push further, we pull out the cable. If there is a blockage at the end, it was a cork and you are on the right track. We clean the tip, run it into the pipe again and repeat the procedure until the pipe is clean. Not the most pleasant experience, but without this, some blockages simply cannot be removed.

There is another way - to make cable ends with rusty edges. They are able to get through the most difficult and dense blockages. Then the cork will not need to be removed in parts, but it will be possible to crush it, and then wash it off. What tips can be made for a plumbing cable - in the video.

Cleaning the toilet with a plastic bottle

If you tried to clean the blockage in the toilet with a plunger, you noticed that this method is ineffective due to the fact that the rubber part does not fit snugly, so the water hardly moves, there is almost no result. There is a more effective, and moreover, cheaper tool - a plastic bottle with a cut off bottom. We take a larger vessel, cut off only the bottom, leave the lid closed.

We bring the cut bottle to the place of the inflection of the toilet bowl, lower it into the water, sharply move it up and down. The movement of water is quite active. In the place of the inflection, “waves” are formed, which break the gradually formed cork. This way to clean the sewer only works if the plug has formed in the kink of the toilet, if somewhere in the pipe, there is only one way out - cleaning with a cable.

First you can try poke through a drain hole toilet bowl, but if it doesn’t work out, it will be necessary to dismantle the toilet bowl and free up access to the outlet to the sewer (this is if there is no revision hatch).

What kind of pollution helps soda and vinegar to clean the toilet

The use of acid and sodium bicarbonate is effective not only in cleaning the surface, the tool will help get rid of blockages in the drain passage and pipe. The main task is to determine the nature of the blockage and the location. The reasons:

• the remains of building materials got into the sewer - this option is considered primarily during repair work;
• the drain passage was blocked by personal hygiene products, and if there is a small child in the house, perhaps the drain is clogged with a children's toy, especially a soft one;
• fruit or spoiled food got into the toilet;
• if there is only one drain from the toilet and the kitchen sink, the pipe may be clogged with compressed fat;
• a common cause is a garbage plug in the main sewer.

In the latter case, more effective measures will be needed than cleaning the toilet with soda and acid.

If the blockage is close, it can be pulled out of the pipe manually; in case of failure, cleaning agents are used. During the reaction of acid and alkali, carbon dioxide is released, and it pushes through the obstacle. You can break the blockage in the toilet with soda and acid as follows:

1. Warm water (about 8-10 liters) is poured into the sanitary fixture and covered with a lid, left for two hours.
2. If the blockage is loose, the water will gradually drain, the residues are completely removed.
3. Use a plunger, it will help to move the blockage from its place with a stream of air.
4. Then ½ a pack of baking soda and 2 tbsp are poured into the toilet. vinegar heated to 400 C.
5. The hole is tightly closed with a rag so that foam does not come to the surface, and carbon dioxide moves towards the obstacle in the pipe, leave for 40 minutes.
6. Then again pour warm water.

A budget and effective way to clean the surface of plumbing with vinegar and soda

Advice! If the first time it was not possible to eliminate the blockage of the toilet bowl with soda and acid, the procedure is repeated.

Cleaning of drain passages in case of severe clogging is carried out as follows:

1. Remove fluid from the toilet.
2. Mix in 1 liter of water 200 g of caustic soda and the same amount of acetic acid.
3. Pour into the drain hole, close the passage.
4. Leave for two hours.

Then the remaining solution is washed off with warm water.

Cleaning the toilet with folk methods

Hot water

Here's how to clean the toilet bowl at home using boiling water. Fill a bucket with water and boil.Immediately flush down the toilet in one quick motion. It is better to immediately prepare two buckets of boiling water and pour them without interruption. Such actions will help if the blockage is simple.

Important Do not pour boiling water into the toilet bowl if it is equipped with a plastic connecting corrugation. The connection will withstand only hot (up to 60 degrees) water

Soda

Now we will tell you how to eliminate a clog from toilet paper using baking soda. We collect 5-7 liters of water in a bucket, add a pack of soda, stir. Pour the solution into the toilet, wait one to two hours. The soda solution will dissolve a lump of paper, corrode fatty formations.

How else to clean the toilet with baking soda and vinegar

You can add vinegar to the soda. The union of the two ingredients will enhance the penetration of the solution. We can do without pre-mixing them. Just pour a pack of soda into the toilet and pour a bottle of vinegar essence. Close the toilet lidWe wait three hours. Boil a bucket of water and pour it out. The cork will dissolve and the drain will be released.

soda and salt

The combination of soda and salt works well for clogging. We take a glass of both ingredients and send it to the toilet. After 10 minutes, pour out a liter of freshly boiled water. Don't rinse all night. During this time, the contaminants that caused the formation of the plug should go away.

Mustard

Another kitchen cleanser will help to deal with blockages. You will need a bucket of hot water. We dissolve 3 tablespoons of mustard powder in it and pour it into the toilet bowl. We drain the water after 10 minutes. If it doesn't work the first time, repeat the procedure.

Cleaning the toilet with a plunger

They work both manually and mechanically. The first to clean the system through the sink, the second to eliminate the blockage in the pipe behind the toilet.The plunger must be with a cone-shaped nozzle at least 10 centimeters in diameter. It is located strictly in the center of the drain hole. If the rubber of the plunger is lubricated with petroleum jelly, it will press against the sink more tightly, and tightness is very important.

While using the plunger, the sink must be filled with water. We make movements sharp, frequent.

A mechanical plunger has a valve in the handle, which is a tube. When the cork is far away, a simple plunger cannot cope. We try to act mechanically. If this does not help, we will call on a vacuum cleaner to help. We are restructuring its work for blowing. We separate the plunger bowl from the handle, attach the vacuum cleaner hose, wrap it with tape. We press the rubber bowl of the plunger to the drain hole and turn on the vacuum cleaner.

brush

How to clean a drain with a brush and a plastic bottle. The method is used when there is no plunger at hand.

We clean the drain hole with a brush. We cut off the bottom from the plastic “one and a half”, leave the lid closed. We lower it all the way and work, like a plunger, up and down, causing a change in pressure. This quick way to clear a clog with a brush and a plastic bottle is good for light stains.

Removing clogs with film and tape

When choosing how to clean the toilet from blockage at home, pay attention to such a non-standard way. Get your scotch ready

Wipe the toilet dry. Seal the circle of the toilet with tape, achieving an airtight coating. Now drain the water and press on the film "lid" with your hand, acting like a huge plunger. When the pipes are clean, remove the tape. On sale there is a special film for such manipulation, which is more convenient to work with.

How to eliminate mechanically?

In the event of serious blockages with complete or partial blocking of the outflow of wastewater, mechanical cleaning methods have shown themselves to be one of the most effective. In cases where the cork is formed by foreign objects, especially those of non-organic origin, such methods are the best.

plunger

One of the simplest devices for cleaning the sink and bathtub is a plunger. The principle of working with it is not complicated:

• place the plunger vertically in the sink with water, holding the handle;
• press the handle, and sharply lift the plunger up and towards you;
• repeat.

With severe blockages, the plunger may be poorly effective.

Cup

If there is no plunger available, and the blockage is not strong, then you can even get by with a glass. How to use:

1. Lower the glass into the sink with water so that the free edge covers the drain hole.
2. With a sharp movement, raise the glass up and towards you.
3. Repeat several times.

With complex blockages, as a result of which the outflow of water is completely blocked, the cleaning procedure with a glass will not be effective.

Cable

Special plumbing cable - a device for cleaning sewers mechanically.

It is a cable, on one end of which a handle is installed for rotation, on the other - a nozzle with a brush, which is designed for cleaning.

The principle of operation is to introduce a cable with a brush at the end into the sewer. By turning the handle, advance the tool along the drain so as to clear the pipes. The cable allows you to clean the drain even with complex blockages.

Useful information

Tips to help deal with clogged pipes:

1. To increase the efficiency of the procedure, after adding the components to the pipe, it must be closed with a stopper. This will increase the pressure and the blockage will be completely eliminated.
2. The following combinations cannot be used: “soda ash and baking soda”, “soda ash and vinegar”.
3. If the blockage is dense, before adding vinegar to the pipe, it is heated to 45-50 degrees.
4. The longer the product stays in the pipe, the better, so it is recommended to apply the mixture at night or before leaving for work.
5. Soda and vinegar are used as mono-means. They are not combined with other chemicals as the reaction can be unpredictable.

If you are interested in how to clear a blockage in a pipe, sink or toilet, take a look at this section.

How to clean a toilet without tools

Before you fix a blockage in the toilet with mechanics or call a plumber, try to handle it yourself using these methods.

Hot water

If the blockage is small and of organic origin, this simple method can help get rid of it. All you need is a bucket of hot water. But be careful: only try the method if you are sure of the quality of the faience. The coating may crack when exposed to high temperatures.

You can't use boiling water, you just need hot water. Deciding to use this method, first splash a small amount of liquid to warm the structure. And only then pour out the bucket. Wait a couple of minutes and drain the water from the tank.

Soda

There are two methods of applying it, and both have proven themselves in the fight against blockages.

The first is to add about half a pack to a bucket of hot water. The lye will break down small organic deposits without damaging the passages.

The second is to first pour out half a pack of soda, and then pour it with a full glass of vinegar. Such a solution will cope with larger organic blockages. A substitute for vinegar can be citric acid or lemon juice. Then flush the toilet, gradually draining the water from the barrel.

If for some reason there was no soda in the house, it can be replaced with Alka Seltzer tablets.

Household chemicals

Simple blockages are also successfully removed by acid-based chemical products. Here you can choose from both domestic developments of the Krot type and analogues - Tiret and Domestos.

When selecting, it is important to clarify the type of garbage that fell into the drain. If it is, for example, a plastic bag, chemicals will not help, they are active only against organic compounds.

Effective methods for clearing sewer blockages

A plunger is a rubber-tipped stick shaped like a large suction cup that can suck or push debris.

Using this simple invention, you can get the following results:

1. Prevent blockages.
2. Eliminate the causes of slow water drainage.
3. Assess the extent of pollution.

Recommendations for the use of a plunger:

1. Install the device so that its rubber part blocks the drain hole.
2. Draw a small amount of water into the bath (dry efficiency is reduced).
3. Make a few strokes by moving the handle up and down.
4. Check if the water is running out.
5. Flush out the trash.

If this did not help and the blockage in the bathroom did not disappear, then what to do? Use rope:

1. Insert it into the drain hole.
2. Push forward into the pipes and scroll at the same time.
3. When the voltage drops (the blockage is cleared), gently move the cable back and forth.
4. Remove and wash the product.

Chemicals

The modern chemical industry has taken care to make the process of removing blockages as fast and comfortable as possible.

Manufacturers vied with each other to produce tools for cleaning pipes from debris and deposits. The form of release can be varied:

• powder;
• gel;
• liquid.

The most common and inexpensive remedy is Mole - a domestic drug that perfectly eliminates odors, food debris and fat, and also breaks down fibers (hair, wool, etc.). Produced by different companies and may vary slightly:

• by composition;
• price;
• action time.

Compatibility with the type of pipes is usually indicated on the packaging. Here is a far from complete list of effective drugs:

1. Mister Muscle.
2. Bugs.
3. Pothan.
4. Tiret.
5. Flup.
6. Mole.

Folk way to clean the blockage: soda and vinegar

If there is no plumbing, no plunger, no cable, no purchased funds at hand and the bath is clogged, it is worth trying the folk method. This will require:

• ½ cup baking soda;
• ½ cup of vinegar;
• 1 liter of boiling water.

Follow these instructions:

1. Wipe the tub and metal drain ring dry.
2. Pour baking soda into the drain hole.
3. Pour vinegar into it.
4. Pour in boiling water after 1 minute.
5. After 2-3 minutes, turn on the water - it should flow freely.

Siphon cleaning

If, nevertheless, there is confidence that a necessary or valuable thing has become the reason for the slow draining of water, it is worth learning how to clean the siphon in the bathroom. Thus, it will be possible to remove what got into the drain and caused a blockage.

Siphon cleaning technology:

1. Lay a cloth under the siphon, put a basin or bucket.
2. Slowly unscrew the lock nut so that liquid does not rush out.
3. Remove the flask and discard the dirty water.
4. Remove any debris, small parts, or clods that are causing the problem.
5. Rinse the siphon and remove plaque.
6. Install the siphon.
7. Check tightness of connections.

Now, in case the bath is suddenly clogged, you will know what to do.

It is also worth watching a video on this topic:

Mechanical Methods

When eliminating sewer blockage caused by foreign objects entering the toilet bowl, mechanical methods that are simple provide a good result.

Cleaning with a plunger

You can deal with a slight blockage using a plunger. At the same time, it must have a cone-shaped nozzle, the diameter of which is 10 cm.

1. Before starting work, fill the toilet bowl with water.
2. Install the plunger in the drain hole and, holding it by the wooden handle, make a few clicks on this device.
3. Then abruptly remove the plunger from the drain hole. Repeat this procedure several times if necessary.

Using a plunger, you can effectively deal with clogged toilets

If there was no plunger in the house, you can use an ordinary plastic bottle, from which you should cut off the bottom and proceed according to the same principle as when working with a conventional plunger.

Use a plastic bottle to clear a clogged toilet

How to clear a blockage in the toilet with a plastic bottle - video

Cleaning the "doll"

To eliminate the blockage, a homemade “doll” can be useful, which is a fabric bag filled with sand and equipped with a long rope.

1. Lower the "doll" into the toilet drain while holding the rope in your hands.
2. Click on the drain and wait until the water flow will carry the “doll” along with it.
3. Then remove the "doll" from the toilet by pulling on the rope.

Due to its weight, the “doll” will be able to break through the blockage formed in the water seal.

Rope cleaning

You can deal with a clogged toilet bowl with a specialized cable. This product is distinguished by the presence of a rigid hollow axis, flexibility and a handle that can rotate. At the end of the axis is a spiral process, attached to the cable itself with a flexible tube.

1. Lower the end of the cable into the toilet drain hole until it stops.
2. By rotating the handle of the device, slowly push the cable into the water seal.
3. After clearing the blockage, flush the system with hot water.

Working with a cable, you can break through the blockage formed in the sewer system

Similar actions can be performed using an ordinary cable purchased at a hardware store.

It is important to choose the right length and diameter of the cable.

How to use the cable - video

Cleaning the toilet with foil

There is another method that allows you to get rid of the blockage caused by the ingress of foreign objects into the toilet. To apply it, you will need a wide adhesive tape.

1. Wipe the toilet seat dry.
2. Start sticking strips of tape on the circle, tightly connecting them together to form a continuous film coating.
3. When the entire toilet is hermetically sealed, flush the water.
4. With a few strong hand pressures on the scotch lid, you can break through the blockage.
5. Remove the tape from the toilet seat when finished.

How to remove a clogged toilet with tape - video

A specialized film created specifically for this purpose will also help to remove the blockage.

Chemical control methods

If mechanical cleaning did not give the desired result, try to “corrode” the blockage by flooding it with “chemistry”. The chemical method is remarkable in that the solutions are poured directly into the pipe cavity.

Folk remedies

In the kitchen, every housewife always has baking soda and vinegar on hand. They will help clean the toilet.

Soda and vinegar, reacting with each other, cause an "eruption", which contributes to the exfoliation of fat and mud deposits on the inner walls of the pipes

The cleaning procedure is carried out in several stages:

• A glass of dry soda powder is poured into the previously maximally emptied toilet bowl. The powder must not be mixed with water or detergents.
• Pour half a glass of vinegar at room temperature into the drain.
• The treated drain hole should be plugged with a cotton piece of fabric so that the foam mass that has arisen during the reaction does not go into the drain, but goes inside the sewer pipe.
• The mixture poured into the pipe is left for half an hour. During this time, it will dissolve small debris and all deposits on the walls of the pipes.
• In the meantime, you need to boil a couple of liters of water. Half an hour after filling the soda, open the hole and rinse it with boiling water.

Dousing with boiling water should not be used for processing plumbing, in which the connecting corrugation is made of thin-walled plastic. For the final treatment in this case, it is better to use water at a temperature of 60-80°C.

We offer you another effective, but unusual at first glance, cleaning method.

Many of us love the sweet carbonated drink Coca-Cola, but not everyone knows that one of the components of its composition is phosphoric acid.

Orthophosphoric acid is able to clean even metal surfaces from rust. It is not surprising that Coca-Cola, which contains this substance in the form of an additive E 338, is able to “corrode” fat and mud deposits on pipe walls.

To clean the toilet, just pour one liter of drink into the drain hole and wait one hour. After this time, the system only needs to be rinsed with plenty of hot water.

Store compositions

If the opportunity allows, special products can be purchased as a chemical flush.

The principle of action of the compositions proposed by manufacturers is to dissolve local deposits, thereby clearing the way for the unhindered passage of water flows

Store funds are available in the form of:

• sprays;
• liquids;
• powders;
• granular substances.

The use of each of them depends on the type of blockage. They proved themselves well: the universal remedy of the American manufacturer "Bio-Favorite", "Potkhan" of Israeli production.

Among domestic manufacturers, the following are especially popular: "Mole", "Biocomposition Vantuz", gel "Tiret".

The chemical agent is poured or poured deep into the drain and wait for the time period indicated on the label, after the time has elapsed, the treated pipes are washed abundantly with hot water

Some owners, trying to enhance the effect of chemical treatment, leave the composition for a longer time than indicated by the manufacturer in the instructions.

It is not recommended to do this, since they contain alkaline substances that can harm the internal walls of the system.

For the same reason, it is unacceptable to use 2-3 funds at the same time. The outcome of such experiments can occur according to one of two scenarios: either none of the means will work, or the cumulative effect of both compounds will lead to serious consequences.

Prevention measures

Any blockage can be broken through, any toilet bowl can be cleaned, but often this requires a lot of money, time and effort. Sometimes it happens that it is not possible to clean the blockage formed in the toilet bowl or in the depths of the sewer pipe on its own. Then you need to call a plumber to your house, but his waiting and work take a lot of time. Yes, and the work of a plumber involves payment, that is, the material costs of the owner of the apartment. Therefore, the appearance of blockages is easier to prevent than to deal with them later.

To do this, you need to follow simple rules. Do not confuse the toilet with the urn and throw various household waste into it. Periodically, for example, once every 2 months, take a kind of preventive measures to combat salt deposits. To do this, you can use special tools, which were discussed above. And of course, even the smallest blockage must be eliminated as soon as possible in order to prevent an unpleasant situation.