How to prepare an all-season prefabricated frame pool for winter?

Preservation of the all-season pool near the house for the winter

Preparatory work on the conservation of the pool near the house for the winter should begin in early autumn, as soon as the swimming season ends.The whole procedure is carried out in seven stages, they must be performed not at once, but gradually, with a break of several days.

Before starting work, it is important to take care of the purchase of chlorine-containing reagents and special compensators

How to keep the pool and cover it from winter precipitation

After the end of the swimming season, seasonal frame prefabricated structures must be dismantled and stored. All-season prefabricated pools and stationary must be carefully prepared for wintering. Pool conservation work should begin when the air temperature drops to 15C.

Below is a step-by-step description of how to keep the pool in winter - from autumn preparation to spring re-preservation.

1. Water from the pool must not be drained, otherwise the freezing soil will inevitably swell and break the structure. So, all cleaning procedures should be carried out in a pool filled with water.

Before conserving the pool for the winter, it is necessary to clean the walls and bottom of the bowl from visible contamination mechanically, using a vacuum cleaner or an ordinary brush, put on a long hollow stick, to which a hose connected to the skimmer will be attached on the opposite side.

2. Next, chemical water treatment should be carried out using chlorine-containing reagents (it will be necessary to equalize the pH to 7.2-7.6 units) or a large amount of hydrogen peroxide (1200-1500 ml per 1 m3 of water). This will protect the water from souring and insects during the cold period.

3. Now you need to run the filter pump for at least 7 hours (without interruption), and then turn it on reverse and rinse the pump filter.

4. It is necessary to dismantle the pump and store it, after removing the cartridge and draining the remaining water from it.The opening in the device must be covered with plastic wrap. Then you should remove the water from the pool to the mark of 80 mm from the edge of the nozzle, disconnect the pump hose and close the hole with a special plug.

5. Before blocking the pool from winter precipitation, expansion joints must be installed. To protect the bowl from the expansion of water during freezing, it is recommended to put foam floats, plastic bottles, canisters, etc. into it.

Expansion joints must be half or completely immersed in water so that the bowl is covered almost to the top. Usually 1 float per 0.5 m3 of water is required. To keep the expansion joints at the right height, sandbags should be tied to them.

It is forbidden to use metal pipes as a weighting agent, do not tie parts with wire: they will oxidize in water and leave rust marks that cannot be removed on the walls of the bowl. You also need to attach expansion joints to the bottom so that they do not gather in one place.

6. Finally, be sure to close the pool with a protective cover. If the plastic screen supplied with the prefabricated pools is to be used, it must be raised in the center so that sediment does not collect inside. This can be done using an inflated cushion float or an ordinary car tire, which must be placed in the center of the bowl.

7. In the spring, the water from the pool must be pumped out, the walls and bottom thoroughly cleaned with detergents, rinsed, and then filled with clean water.

Similar posts

How to prepare an all-season prefabricated frame pool for winter?

For the first time, a frost-resistant prefabricated pool was purchased. I like everything very much. Only the thought of how the design will winter is haunting.Please advise how to properly winterize such a pool?

Don't worry, framed pools usually handle the cold season well. Of course, provided that they were properly prepared for it. The process of conservation of the structure should be started at a temperature not lower than +15C. It is carried out in several stages.

Removal of contaminants and treatment of the pool

We start by removing visible contaminants. We do not drain the water. Thoroughly clean the walls and bottom of the pool with a special vacuum cleaner. You can use a homemade design, which is a fairly stiff brush, mounted on a long hollow handle. The opposite end of the handle is connected with a hose to a working skimmer. The filters of the device will remove impurities from the water and send the purified water back to the tank.

The next stage is the shock chemical treatment of the pool with chlorine preparations. Hydrogen peroxide can also be used for these purposes at the rate of 1200-1500 ml per cubic meter of water. In this way, it is possible to equalize the pH environment in the tank and protect the water from acidification and insects. After adding chemicals to the water, the circulation pump must operate for at least seven hours, after which we switch it to reverse and rinse the filter of the device.

Dismantling the pump and protecting the bowl from damage

Now you can start dismantling the pump. We drain the water from the tank to a level of about 80 mm from the lower cut of the water supply nozzle. The pump hose is disconnected from the pool wall, the hole is closed with a special plug, which should be supplied with the tank. Before laying the pump for storage, we carefully inspect it, free it from water that could remain inside the structure.Then we remove the sand filter, which must be stored separately and dry the equipment well. We close all openings in the case with a film and remove the device in a dry place.

To protect the bowl from damage that may result from the expansion of frozen water, special expansion joints should be prepared. These can be poorly inflated car tires, foam floats, canisters or plastic bottles. They are placed over the entire surface of the pool so that the surface of the water is almost completely covered with them. On average, one compensator should be for every half a cubic meter of water. The floats must be fixed to the bottom of the tank with special weights, such as sandbags.

A small nuance: metal pipes cannot be used as a load, it is also not recommended to fix the compensators to the weights with wire. This is explained by the fact that the metal in the water is subject to corrosion and can leave traces of rust that cannot be removed on the walls of the tank. Fixing the floats to the bottom is required. If you just scatter the expansion joints, they will inevitably huddle together in one place, which makes their use useless. Therefore, you will have to go down to the pool, put each float in its place, tie them with a rope and fasten its ends to the sides of the container.

What is the best way to hide?

In conclusion, we cover the tank with a special plastic screen, which should be included with the pool. To prevent precipitation from accumulating on its surface, you need to raise the center of the canvas.This can be done with the help of special inflatable float pillows or an ordinary inflated car tire. We install the structure in such a way that its upper edges are located above the sides of the pool. The float, exposed in this way, will raise the center of the screen to a height sufficient so that precipitation does not linger on its surface. Now the pool is completely ready for the cold.

Where to store frame pools?

Many store the pool cover folded right at the place of its installation. Protection from the influence of external factors is a dense polyethylene film, pressed to the ground with bricks. This is done with large containers that are difficult to carry, or that take up so much space that they simply do not fit in the barn. It cannot be said that this is the right decision, but in this way the plastic is protected from heaving of the soil and the pressure of frozen water.

Since the plastic becomes brittle when frozen, it is advisable to store such pools in a room with a positive temperature. If the folded tank takes up little space, then it can be stored at home by placing it at the bottom of a sofa or closet. If there is an insulated loggia, the packed tank can be taken out there.

Most owners of frame collapsible pools prefer not to clutter up their living quarters with voluminous bales of rolled-up film. For storage, any room with a sealed roof and blank walls is selected:

• barn;
• workshop;
• attic;
• basement garage;
• summer cuisine.

The place of laying should be such that the bundle does not interfere with the passage, the possibility of heavy and sharp objects falling on it is excluded.It is advisable, after the onset of frost, not to move the packed bowl from place to place until stable heat sets in and the plastic is completely softened.

Pools that do not need to be cleaned for the winter. Is it possible to leave the frame pool for the winter?

After the end of the swimming season, many are wondering if it is possible to leave the frame pool outside in winter?

It is possible, but only if the pool bowl is made of frost-resistant material. These are all-weather frame pools that are made of thicker material and a more durable frame. Summer-type frame pools made of PVC fabric will definitely have to be dismantled, otherwise they will simply crack and can be thrown away.

Pool Conservation Rules

You can not leave the container without water, otherwise the frame will be deformed, and the film will be covered with microcracks. Rodents can climb into an empty pool and hopelessly ruin it.

Before pouring fresh water, the bottom and walls of the pool must be thoroughly cleaned of plaque;

The water level in the pool should be left just below the nozzles and chemicals should be added to the water. On sale there are special winter preservatives that prevent the development of mold, fungus, algae and microorganisms.

Filter the water for 2 hours so that the water does not bloom;

It is necessary to take empty plastic bottles with a load, tie them together and distribute them around the pool. They will take the load upon themselves, preventing the ice from breaking the awning when expanding;

Be sure to remove all equipment: skimmer, tubes, filter. Rinse them thoroughly, dry them and put them in a dry room;

Plugs must be placed on all inlet and outlet openings;

Cover the pool with a strong awning so that debris and precipitation do not get into it.

Naturally, to leave the frame pool for the winter, you will have to work hard and spend more than one hour. But given that it's not cheap, it's worth it to get it right. Then it will serve you for more than one year.

After such preparation, the pool is not scary to leave in the cold on the street and go home. With the onset of heat, it will be quite simple to prepare it for the new bathing season. You will need to connect all the hoses, equipment, add chemicals and fill in fresh water. It remains only to wait until the water warms up and you can swim.

In principle, if you have a frame pool installed on the ground, then it is easier and more reliable to disassemble the frame, dry it, fold the bowl material and put it in a warm room. Well, for those who have a pool dug into the ground, of course, the only way out is conservation for the winter.

How to wash the pool before storage

Preliminary preparation of the tank for storage includes its release from water and purification from dirt and debris. You can empty the tank through special drain holes or using a submersible type drainage pump. Children's models simply turn over and pour water onto the lawn. For overall structures, a hose should be used, which is inserted into the drain hole and the water is redirected to the pit, storm drain.

The use of special products for cleaning the pool allows you to keep it intact for many years.

Advice! If the pool does not have a drain valve, then you need to immerse one end of the hose inside the bowl, and draw air out of the other. After that, direct the water to the place designated for these purposes.

It is recommended to wash the tank with a sponge, a soft cloth, a brush on a telescopic handle is also suitable.Liquid soap should be added to the water to clean the pool, the use of abrasive cleaners should be avoided. They contain hard particles that can severely scratch the plastic.

Recommended reading: How to wash a blanket made of wool: camel and sheep

Given that the surfactant is not washed off from the surface for a long time, it is necessary to rinse the bowl inside and out several times. If you ignore this point, then the next time the pool is used, the water will begin to foam. And soapy liquid does not have the best effect on the human mucosa.

When using a collapsible structure, all its components must be cleaned of dirt separately. For them, liquid soap is also diluted with water in a container, thoroughly washed with a sponge.

Should the frame pool be removed for the winter? How to store a frame pool in winter

Pleasant to use and easy to store

How to store the frame pool in winter? Read about the storage conditions of frame pools in our article.

If you still decide not to, but to remove it, then of course this is also the right decision. Especially if the pool bowl in the country house is not deepened, but simply stands on a prepared cemented site, with which nothing will happen in the winter.

Storage of the frame pool in the winter is also possible in assembled form. It is more convenient to prepare the pool for dismantling before the onset of cold weather. If you use a special pump with table salt, which, passing through itself, purifies water, then such a liquid without chemicals can be drained into the garden. But the use of chemistry for the pool is almost a prerequisite. Since warm water will bloom in a week. Therefore, it must be drained into the sewer.Of course, it is more convenient to prepare a drain hole for the pool and not puzzle over where to drain the water every year.

Storage conditions for frame pools

There is nothing complicated, you just need to follow certain steps according to the instructions:

1. drain the water
2. thoroughly wash the walls from plaque and mold. You can do this with a regular brush for the car. It is quite tough, but will not damage the PVC. And the detergent should not be aggressive,
3. remove all existing equipment, rinse well, dry and carefully fold into a dry box.

ADVICE! It is advisable to dry the structural elements in the open air, ideally in the sun, while the pool should be left in the open air for at least 1 hour.

If your bowl consists only of metal supports and an awning, then winter storage of the frame pool must be done in a dry, warm room. Disassemble the structure into elements and mark it so that the next year it would be easy to assemble the frame. Take special care of the film. First, rinse it thoroughly, and dry all the folds from the outside and inside.

Hurry up - make people laugh

After the material is completely dry, sprinkle it with talcum powder. This is necessary so that the storage of the frame pool in a folded form does not lead to gluing of the material from which the bowl is made. A rectangular pool is much easier to roll than a round one. Roll like a regular sheet, smoothing out any wrinkles. With a round pool is more difficult. Fold inside the walls of the bowl, then the circle in half twice. Get a triangle. You can not leave the pool in an unheated cottage

It is important to store the film in a dry, warm place, as frost will make it brittle and the next year it will crack and have to be patched. Nothing can be placed on top of the rolled PVC film in order to avoid creases and keep animals out

ADVICE! In order for the pool to be conveniently folded, it needs to be shaped into a square. This can be done like this:

• start folding the product on one side, while wrapping about 1/6 of the material;
• repeat the manipulation on the other side, folding the material several times so that in the end the folding design resembles a book.

Easy peasy

How to store a frame pool bowl if it consists of a frame and plastic or metal shields? Everything is much simpler here. Preparing the pool for cleaning is the same as everyone else. And the assembly of the structure is complemented by plastic or metal shields. All plates are washed, wiped, folded and removed. The temperature regime is not important for them. But with the material for the bowl, the requirements are the same.

ADVICE! For proper storage, it is important to choose a suitable room. The room should not be too hot (ideally, if the room is cool, not higher than 18 C), and it should not be humid here and there should be good ventilation

After reading our article, now you have an idea how to store the frame pool. It remains to make it a reality. We hope that you will not have any difficulties and difficulties. The main thing in this matter is not to rush, so that next year you will again enjoy the cool water in your pool.

Storage rules

From the competent storage of the pool in the winter, it directly depends on the state in which it will meet the new season.

How to wash and clean before wintering?

The classic way to clean a seasonal pool from dirt and plaque:

1. Cleaning begins by opening the drain hole. If before that detergents were added to the water, it must be drained strictly into the sewer, excluding ingress into the soil.
2. The rest of the water is scooped out with an ordinary scoop.
3. With a brush with synthetic bristles, the plastic sheet of the pool is thoroughly cleaned of silt. It is not recommended to use a metal brush - it is easy to damage the material.

Seasoned pool users have come up with many interesting cleaning methods.

Here are some of those recommendations:

• Having drained the water to a level just below the knees, you need to clean the walls with a brush, wetting it in water. The pump continues to work and pump out water. Then, having adapted a regular vacuum cleaner to the pump, vacuum the bottom of the pool. At the end, wipe the bottom with a rag and leave for a day to dry.
• You can also drain the water by gravity by attaching a hose to the drain hole. Of course, this process will take several hours.
• When installing the pool, it is recommended to make a recess under the bowl: then, after draining, the remaining water will collect there, and it will be easy to scoop it out without driving water around the entire bottom of the pool.

How to unmount?

The method of folding the plastic bowl depends on the shape of the tank:

• If the pallet is rectangular, it must be folded like a sheet, avoiding folds and creases.
• Folding a round bowl begins with laying the walls inward, after which the bottom is folded in half twice. The result is a triangle, which is further reduced to a convenient size.
• If there is a cable inside, then it is removed from the loops.

Before folding the canvas, control drying of all folds and hard-to-reach places is done so that not a single drop of water remains. Only a perfectly dried pool is guaranteed to last until the next season. Small-sized bowls can be dried by hanging on the clothesline.

The frame is quite easy to disassemble:

The pins are unscrewed, the side and lower hinges are disconnected, the beams are removed.
The vertical supports are dismantled, the nozzles, hinges and hinges of the awning are removed.
During the dismantling process, it is important not to forget to rinse the drain hoses: it is good to do this with a mixture of citric acid and Feri type dishwashing detergent.
All components are labeled and packaged.

How and where to save construction details?

Frame parts (unlike the bowl) normally tolerate low temperature storage. Therefore, having packed and labeled them, it is quite possible to leave them for the winter in a garage or country house. As for the bowl, it is required to store it only in a heated room.

The pool canvas is perfectly stored in the vegetable store. Holes formed at the places of creases can be completely repaired with self-adhesive cheap patches: such repairs can withstand one season perfectly.

How to re-preserve before the start of the swimming season?

With the onset of warm spring days, I want to put a home reservoir into operation as soon as possible. This must be done correctly.

seasonal pattern

Before installing a seasonal pool, first tidy up the area where it will be located:

1. The area is cleared of debris.
2. The platform is leveled, and a litter is laid on it, which will protect the bottom of the pool.
3. Stakes are driven in, onto which the frame is pulled.
4. All parts must first be washed and the pool rinsed.

Frost-resistant pond

In no case should you break blocks of ice with a crowbar! Wait until the ice melts naturally.

It is necessary to start cleaning the stationary pool after the winter as soon as the night air temperature is set at 10 degrees. If you stretch the time until the heat, the water will certainly "bloom".

If the pool was covered from above for the winter, then there will be much less debris in it than in the open.

But in any case, thorough cleaning and washing with disinfectants will be required:

• Having descended into the bowl, you should thoroughly rinse every corner of the pool. This is done with the help of brushes and (and) vacuum cleaners. Special chemistry for pools should be added to the water, which does not create foam (it will be very difficult to get rid of the foam after draining the water).
• Release nozzles and skimmer from winter plugs.
• After de-energizing the system, install spotlights.
• Install ladders and handrails.
• Connect pumps and filters.
• Install disinfectant equipment.
• Pour water into the pool, exceeding the level of the middle of the skimmer by 3-5 cm.
• Adjust the acidity of the water.
• Perform shock treatment of water with a chlorine-containing substance.
• Without turning off the filtration, leave the pool for 1 day.
• Dirt collected at the bottom in the form of sediment must be carefully collected with a vacuum cleaner.
• The filter needs to be washed a couple of times.
• Turn on the ultraviolet and filtration system.

After carrying out all these procedures, the pool will be fully prepared for operation.

Preparing the pool for storage

Even seasonal bowls do not require special storage conditions.They can be kept without any risk in rooms that are not heated. So the risk that the frame collapsible pool will be harmed will be reduced to zero.

The general rules for dismantling and storing a frame pool in winter are as follows:

1. Work on the dismantling of the summer plastic pond must begin long before the onset of cold weather and prolonged rains. To prepare the tank for packaging, it will take at least 2 days: one will go to the cleaning work in the pool and its dismantling. Another 1 day is needed to dry the plastic tank, stack it and transport it to the storage site.
2. Before draining the water, thoroughly clean the walls of the tank. To facilitate and speed up this process, you can pre-pour detergent into the water, which will soften the plaque. However, pools must be handled with care, choosing chemicals carefully so that the corrosive liquid does not damage the film and metal parts.
3. Plastic must be well cleaned of silt deposits and limescale. This procedure must be performed simultaneously with the discharge of water, opening the drain hole as the walls are cleaned. It is recommended to clean off the dirt with a stiff brush with polyethylene bristles so as not to scratch the film.
4. After cleaning, the canvas must be removed and dried well. To do this, you can use strong ropes stretched between poles and trees. If necessary, hard-to-reach places are wiped with a rag. Absolutely dry tanks can be sent for storage, otherwise fungus and mold will form on them.
5. The reservoir folds up. This must be done as tightly as possible. Firstly, compact packages are much easier to move around and find a place to store.Secondly, tight packing eliminates the possibility of cracking when a frozen tank is accidentally stepped on or moved to another location. Thirdly, the lack of gaps prevents insects, rodents and snakes from getting into the folds of the plastic.

It is recommended to sew a durable tarpaulin cover for the tank. This solution will protect the plastic from moisture and mechanical damage during transportation.

Conservation of the pool for the winter

Any pool, portable or stationary, which is outdoors in the summer, requires special preparation for the winter. Preservation of the pool for the winter is necessary if you plan to use it next year.

Most outdoor pools do not survive the winter if they are not properly prepared for the cold. Inflatable pools crack quickly, frame pools can leak.

Only a few manufacturers of modern pools, mainly models with hydromassage, assure that their products do not need protection, just drain the water and let the bowl dry.

In other cases, it is better to play it safe and prepare the reservoir for wintering in order to reliably preserve it.

As a rule, outdoor pools of any type, before they are removed for the winter, need to drain the water and thoroughly clean the inside of the bowl.

Here you can use mild cleaners and disinfectants that will remove accumulated dirt from the walls and do not harm the surface. Proven chemistry for the pool, including for water treatment. Here you will find a lot of safe and effective products for your pool.

Conservation of an inflatable pool for the winter

Perhaps the easiest way is to remove the inflatable pool for the winter.Small children's pools are first washed from the inside to remove sediment and dirt.

Then the rubber pool must be dried well. The easiest way to do this is in a draft, but not in the open sun. Sprinkle the walls of the pool to be laid lightly with talcum powder and place in a bag or bag.

You can store such a pool in the pantry. It will not take up much space, and it will not crack during the winter, so next year you can safely use it.

Another type of inflatable pools may have a metal frame and a filter for water purification. Such pools require more thorough cleaning.

• The water in the pool is going down.
• It is necessary to thoroughly wash the walls and bottom of the pool to remove plaque and accumulated dirt.
• The filter of the inflatable pool requires special attention. It is thoroughly washed in several modes of operation.
• Next, the pool must be allowed to dry thoroughly, disassemble the frame, roll up the inflatable base.

As a rule, such pools have their own storage case, where there is room for a metal frame, pump and other accessories. It is better to store this type of inflatable pool indoors so that the cold air does not damage them.

The pool for children and adults can also be of the frame type. In this case, its conservation for the winter is somewhat different.

Preservation of the frame pool

Frame country pools are divided into two types:

Based on the name, it is not difficult to guess that the former require special preparation for the winter and they need to be removed from the open air, while the latter can overwinter right on the site.

Prefabricated pools are conserved for the winter in the same way as rubber ones. The pool is thoroughly washed and dried.Prefabricated pools have quite a lot of components that are also thoroughly washed.

The water supply system must be deprived of water. When the pool is dry enough, it is covered with a special awning that stretches over the pool bowl.

Frost-resistant pools, according to manufacturers, are not afraid of cold weather. But they should also be properly prepared for wintering. Such pools are conserved in the same way as stationary models.

Conservation of a stationary pool

In stationary pools, water is left in the bowl for the whole winter. This prevents the deformation of the bowl, which in winter seriously presses the ground from all sides.

However, the water in which you bathed in the summer is not suitable for conservation. It is drained after the pool filters are thoroughly washed in the circulation system.

After draining the water, thoroughly clean the walls and bottom of the pool. You can use specially designed cleaners for this. Also may be useful pool vacuum cleaner, which effectively removes plaque from the walls and rids the bowl of dirt.

Do not use pool cleaning, which you are preparing for the winter, aggressive detergents, which can serve as an additional load on the wall material.

Another important detail is the need for compensators in the bowl, which will reduce the load on the walls of the pool when the water freezes. Empty plastic bottles and other similar containers are usually used as compensators.

You can cover your pool with a special awning, pulling it over the bowl, or you can leave the pond open. On this, the conservation of the pool can be considered completed.