Hairy problem: how to quickly clean the bathtub drain from hair

How to reduce humidity in the bathroom?

There are several ways to deal with high humidity in the bathroom:

• clean the ventilation - it is imperative to wash the grate, on which a large amount of dust and dirt accumulates over time;
• get rid of wooden cabinets and cabinets, preference should be given to plastic and metal products;
• ventilate the room after each bath;
• install an additional fan in the hood;
• leave a small gap between the door and the floor - you need to think about this even during the installation of the door;
• do not dry things in the bathroom;
• wipe the water that got during bathing behind the bath and on the floor;
• check the health of the pipes.

Hydrodynamic method

This method of cleaning sewer systems is very effective. Washing is fast and efficient.

The most important advantage of the hydrodynamic method is that it does not damage the pipeline, but on the contrary, its service life is extended, since the method is gentle.

This method is also environmentally friendly and destroys deposits of any kind.

Hydrodynamic cleaning is carried out only by plumbers, since its application requires special equipment.

The technique involves the release of a jet of water under pressure, its temperature can reach 120 degrees.

The hose with the nozzle moves further thanks to the jet thrust, which is created by high-pressure fluid jets.

Hydrodynamic washing is recommended 1-2 times a year. Thanks to this cleaning technique, the sewer system will work smoothly throughout the year.

How to clear a blockage in a sewer pipe with a cable

Rope cleaning requires 3 simple steps

Step 1. Begin to carefully insert the cable into the drain hole. Unscrew the drain cap if necessary. Push the rope until you feel it stop. Since we do not see how the cable moves, it is necessary to understand that not every obstacle is a blockage, it may be a joint or a bend in pipes. To make sure that the cable has reached the blockage, pull it out a little and push it again. If you again ran into an obstacle - this is really a blockage.

Step 2. Having reached the blockage, we begin to reciprocate so that the cable destroys the seal in the pipe. It is better if you have an assistant, since, in addition to pushing the blockage, it is desirable to rotate the cable - this is necessary to bypass bends and joints at the pipe junctions. By the way, there are cables with a handle for rotation - one person can use it, that is, you can immediately push the cable through the pipe and scroll. It is advisable to pour hot water into it at the same time as cleaning the pipe. This will help loosen the blockage.

Particular attention should be paid to the cable tension during operation. If the tension is loosened, it may twist, which will lead to damage, and its further use will be difficult.

Attention! Hold the cable well in your hands or fix its unreeled part so that it does not fall into the pipe. It will be difficult to get it in this case.

A cable with a handle will protect you from such a situation.

Step 3. After you stop feeling resistance, flush the pipe with a stream of water.

Cleaning the surface from limescale

Do not know how to wash the bath from limescale? Write down a proven recipe and our tip #4:

1. Half a cup of soapy water. You can use dish detergent, liquid laundry soap, etc.
2. Half a cup of baking soda.
3. 3 tablespoons of vinegar.

All ingredients are mixed and applied to contaminated elements. After half an hour of soaking the solution, you need to thoroughly rinse with plenty of water.

Advice! In order to prevent the appearance of limescale, we recommend using water filters. The cleaning system will make the water softer, which will save the surface of the bathroom and tiles from specific plaque.

Chemicals

The use of chemicals is more expensive. But they differ from folk higher efficiency. Ideally, of course, it is better to always keep a package of some kind of anti-blockage product at home so that you do not have to rush to the store in a hurry.

All chemicals should be used only with gloves and in a ventilated room. Open the door to the bathroom, and open the window in the next room.

Expel "Volosogon"

A set of tools specifically designed to remove hair plugs from the drain. In stores you can find sachets (sold in packs of two, one bag is enough for one use), gels and liquids. In terms of efficiency, they are exactly the same. They do not contain chlorine and do not leave behind an unpleasant odor. The method of use is simple - pour into the drain, leave for 20-30 minutes, rinse.

Expel products are sold in different forms - sachets, gels, liquids

shumanit

Shumanit is a universal remedy, which, moreover, does an excellent job with hair plugs. In stores you can find shumanit from different manufacturers: BAGI, Cinderella, Every Day... They are about the same in terms of efficiency, so take the cheapest one.

Shumanite is a granule that needs to be poured into a pipe and pour a glass of boiling water on top. You will immediately see a chemical reaction - a dirty gray foam will come out of the drain. Then you need to wait about 2 minutes and rinse with warm running water. This is a very caustic agent, so you can not leave it for a long time in the pipes. But after such a cleaning, the pipes are cleaned not only of hair, but also of other dirt.

For example, BAGI shumanit costs about 80 rubles per package, which is enough for 2-3 uses.

footage

Expensive and aggressive products will be a thing of the past if you use baking soda and vinegar. You will not only save money, time and effort, but also protect yourself and your household from the harm of “chemistry”. However, remember that the presented folk recipes apply only to cast iron and iron structures, and modern plastic inserts are very sensitive and can be damaged by aggressive substances. We hope that the information, recommendations and advice received will help you decide on the question of how to clean the bath to white at home, and you will be able to maintain the perfect cleanliness and whiteness of all plumbing without using harmful chemicals. Good luck!

Latest Articles

How business ombudsman Boris Titov assesses the situation in the economy

The indicators of success in macroeconomics, which were accepted as the main criterion for success in the past, for modern Russia should take a back seat, giving way to innovation and ...

Sights of Krasnodar

This city has a great history was founded in 1792, and during this time managed to acquire its cultural heritage. Krasnodar is considered the southern capital of the country, it is a large developing city, with…

Eurowindows - visiting card of the house

Windows are one of the main structural elements of the house, which are designed to protect us from heat, cold and rain. Some windows do this better than others. According to statistics in Russia through ...

High-quality design of curtains in Tver - who to order

Curtains, if they are of high quality and properly selected, can literally transform the look of almost any room.

From homes to halls in restaurants, the importance of…

Apartments with finishing or economy?

Some want to buy real estate in St. Petersburg and immediately live without wasting days and money on wallpaper and tiles. Others prefer to do everything to their liking, because no developer will pick up ...

What bonuses does Lev Casino provide?

Virtual gambling establishments have long understood that the practice of providing players with bonuses is one of the highest quality ways to attract new customers. Many sites like this...

Tips for blockage prevention

Experts recommend the following measures to prevent the formation of a garbage plug:

• installation of a mesh of the appropriate size in the drain hole.It will collect small particles, usually freely washed off with water into the siphon, sewer communications. Special inserts are also offered - hair catchers, thanks to which all fibers that fall into the outlet can be easily pulled out as needed;
• every 2 weeks, you need to drive hot water into the system by means of a plunger - it will take with it part of the adhering layer that clings to its hair;
• it is advisable to flush communications every few months using folk recipes or specialized household chemicals.

Constant attention to the state of plumbing and compliance with safety measures will increase the comfort of water procedures, help to avoid the formation of plugs from solid particles

Factors that affect the formation of plaque in the bath

The appearance of spots is affected two main factors. The main one is water. By divorce, you can determine the quality of the liquid in the apartments:

• if yellowish stains have formed, it contains impurities, chlorine compounds or metal molecules;
• the appearance of brown, reddish spots, rust - iron, it's time to change outdated plumbing;
• cloudy sediment indicates hard calcined water.

The second factor is dirt and dampness. Everywhere, including on the tile, there are splashes, stains from toothpaste. A soapy residue appears on the surface, which must be scrubbed off. After use, it is necessary to clean the bath with soap or liquid detergent, wipe dry. Then you do not have to remove stubborn stains.

How to remove hair from a drain?

There are two ways to get rid of hair in the drain: mechanical and chemical. Devices for their extraction:

1. Rope. It can be used to remove hair and blockages that are deep in the drain.It is introduced into the pipe by turning the handle. When the cable hits a lump, resistance will be felt.

   It must be gently softened by moving the cable back and forth. When the water begins to pass, the cable must be removed. Hair will come out with it.

2. Plunger. It is installed on the drain hole and actively pressed on the handle. As the movements are performed, the blockage will begin to come out of the drain, and the existing hair will rise up. They need to be picked up by hand and removed.
3. Brush-brush. It acts like a cable, but not so long. The brush is placed in the drain and scrolled. The hair will be removed along with the brush.

Chemical hair removal products are divided into improvised and professional. The most effective folk recipe is a mixture of soda and vinegar. It is poured into the drain, left for an hour, and then washed with hot water.

Store compositions are presented in a wide range. They are based on potent acids, so they must be used strictly according to the instructions.

Popular means:

• Chirton powder, price - 30 rubles;
• Bagi granules Potkhan, price - 540 rubles;
• Mole powder, price - 30 rubles;
• Tiret gel to eliminate blockages, price - 220 rubles;
• Chistin gel for cleaning pipes, price - 50 rubles.

The selected agent is poured or poured into the drain, left to act and washed with water. To enhance the effect, you can combine chemical and mechanical methods.

This article will tell you how to eliminate blockage in the bathroom.

5 tips to help wash the bath with improvised means

Despite the fact that the market offers a huge range of products that allow you to quickly clean any surface, many housewives are constantly looking for new methods to clean the bath from plaque as safely as possible for enamel.Such a desire is connected with the fact that not all means that are well advertised cope with pollution. In addition, you can often hear feedback from consumers who have had to restore the surface of the bath or buy a new product after aggressive compounds have been applied.

Experts recommend not to forget about the tools that are in every home and are available to housewives. The use of simple substances, both separately and as part of safe mixtures, can also give a positive result. The main thing is to know how to use each of the ingredients correctly.

Tip #11 – Acid Impact

The use of acid is the first thing that comes to mind when the hostess asks how to clean the bath if lime deposits appear on it. Everyone knows that acid quickly destroys them. You can choose vinegar or citric acid. For the method to be effective, we recommend using the following cleaning scheme:

1. Fill the tub with water. The water temperature should not be hot - no more than +45 ° С.
2. Add a glass of vinegar or a pack of citric acid to the water. We mix.
3. After the liquid has stood for about 3 hours, you need to drain the water, wash off the remnants of lime contamination, and then wipe the surface of the bathtub dry.

Tip #12 - Alkali

The simplest and most affordable substance is bleach, which is in every home. In addition to giving the enamel a snow-white appearance, its use will prevent the development of bacteria on the surface. Its only drawback is a pungent smell, but if this does not bother you, feel free to use this cleaning agent.

The following steps will help you understand how to clean an old bathtub to perfect whiteness:

1. The tub is filled with cold water.
2. A bottle of bleach is poured into it.In this state, the liquid should be left for 10-12 hours, ideally overnight. It is advisable to close the doors to the bathroom so that the chlorine vapor does not get into other rooms of the apartment.
3. After draining the water, rinse the surface with warm water.

This method is effective in combating mold, which can develop in rooms with high humidity.

Important! You need to work with gloves so as not to damage the skin of the hands

Tip number 13 - two types of soda

A serious blow to rust and other types of pollution will be the use of two types of soda at once, mixed at a rate of 1: 1. Take baking soda and soda ash. The components are mixed and diluted with water so that a mixture is obtained, in the form of a slurry.

With this composition, you need to rub the entire surface, paying special attention to those places that are most contaminated. In this state, the enamel should be left for 10 minutes.

After that, you can clean the bath with baking soda and vinegar, or use a mixture of vinegar and bleach. Each component is taken in 50 g. The composition is applied over the soda. After waiting half an hour, you can thoroughly wash off the surface.

Tip #14 - Perfect Whitening

By following the following procedure, you can return the former whiteness, even to the old bath:

1. From half a pack of soda and a small amount of water, make a gruel.
2. The surface of the bath is well rinsed, and its walls are carefully processed using the prepared mixture.
3. The composition will begin to corrode pollution in 1-2 hours.

After two hours of exposure to soda, it is necessary to dilute citric acid with a small amount of water. Using gloves, you need to moisten the sponge in acid and wipe the surface. Thanks to such actions, acid and soda react, and the dirt goes away.You just have to wash it off.

By doing such simple manipulations at least once a month, you can keep the snow-white appearance of the bathroom for a long time.

Tip #15 - Hydrogen Peroxide + Baking Soda

The advantage of this composition will be the possibility of using for acrylic baths. Soda is taken twice as much as hydrogen peroxide, and a paste is prepared. Then the composition is applied to areas that are most contaminated. Within an hour, the mixture will dry, and then it can be washed off with warm water. You can use vinegar instead of baking soda.

Wire twisting

The method was spied on by plumbers who come to clean the sewers with a special durable and flexible cable.

As an analogue, you can use a wire.

1. Twist the wire and make a small hook out of it. For example, copper wire 1.5 mm thick is suitable.
2. Gently push into the drain.
3. Turn around the axis 2-3 times and pull out everything that hooks the hook. Some experts advise combining translational and rotational movements to achieve the best result.
4. Repeat if necessary.
5. Rinse the drain with clean water.

The procedure should be carried out on a regular basis so as not to accumulate blockage. Care must be taken, otherwise there is a risk of damaging fragile plastic structures with metal parts.

How not to clean an acrylic bath

As the old Latin proverb says, repetition is the mother of learning. Therefore, we repeat once again to remember how you can not clean an acrylic bath.

1. Acrylic bath has a good strength in the absence of hardness. Therefore, it can be easily scratched by all kinds of metal accessories designed to care for household items and things: a brush, a scraper and a washcloth.

Also, you can not use brushes with hard bristles (in truth, all), melamine sponge and a sponge with abrasive applied. Under the ban are special cleaning products in the form of powders (Pemolux, Comet, Biolan, etc.), which also leave traces.

2. Acrylic plastic is very sensitive to many chemicals found in household chemicals and cosmetics. In this regard, detergents in the form of gels, sprays and emulsions containing chlorine, acetone, formaldehyde, ammonia, alcohols, alkalis and acids are also prohibited.

Exceptions from this list are allowed if the concentration of ammonia, alcohols, alkalis and acids is very low. For example, if you wet a sponge or rag with detergent and wipe the surface of the bowl, it will be a disaster. If you pour a little detergent into a bathtub filled with water, then there will be no negative consequences. Therefore, the use of detergents such as Sarma, SanClean, Luxus professional, L.O.C. Plus, Cillit, Acryl - Net, Star - Acrylat, Triton, RAVA K and Panni for cleaning the font only at the owner's own risk.

Mechanical ways to clean the sewer

These methods are among the most cardinal and effective. When chemical-thermal methods have exhausted themselves and have not brought the desired effect, they turn to mechanical methods for help and use them to remove blockages in pipes at home.

Siphon cleaning

If the cause of the blockage is in the immediate vicinity of the place where the water drains, then it is much easier to disassemble the siphon and rinse it thoroughly under running hot water.The siphon performs the function of a hydro-barrier, preventing the ingress of unpleasant odors from the sewer into the apartment. Therefore, the appearance of an unattractive amber, combined with a difficult outflow of water, indicates that it was the siphon that was clogged.

Using a plunger

This French word is called the simplest hand-held plumbing tool, consisting of a rubber valve and a wooden handle. The principle of operation of a plunger is similar to that of a pump. The drain hole is closed with a rubber valve, and then the water flow is injected with reciprocating movements, first in one direction, then in the opposite direction. For more efficient operation, it is necessary to plug the emergency drain hole with the help of improvised means (for example, a wine cork). The plunger is effective if the blockage is located near the drain hole, usually in the siphon.

Plumbing cable

Special flexible cable It is made of metal and consists of an outer shell, inside of which the cable itself is located. At one end of this device there is a special handle for rotation, at the opposite end there are hooks and grippers, with which the blockage is cleared. The cable is used to clean places located much further than the siphon, so it is better to remove the latter before starting work, since its bends and knees will not make it possible to push the cable to the desired depth. The cable is rotated clockwise, as rotation in the opposite direction can damage its sheath.

It just so happened in our family that we always buy Mole to eliminate blockages in the sewer. We've been using this product for as long as I can remember. Most often for prevention purposes.If something is serious, then the husband uses a special flexible cable. With it, you can extract a whole bunch of any, excuse me, garbage from the sewer pipe.

Nadezhda, 28 years old

As a person with a higher education, I once graduated from MEPhI with honors, but for the past few years I have been forced to work as a plumber, I can say the following. Do not attempt to clear any major blockage in the sewer system yourself. It won't lead to anything good, but it's easy to do bad things. Call immediately professionals who have more experience and the necessary tools are available.

Nikolai Alexandrovich, 40 years old

I don't believe in all these modern chemists. They will write anyone, but in fact the bleach is solid, there is nothing to breathe. Another thing is the old grandfather's way, which my mother taught me, the kingdom of heaven to her. We take soda ash and pour it into the hole, and therefore pour five liters of steep boiling water there. And that's it, no smell to you, no stink, and the sewerage is as good as new.

Zinaida Sergeevna, 65 years old

Originally posted 2018-03-03 06:29:28.

How to remove rust

It is difficult to clean rusty streaks and stains. The following products help.

Lemon juice

Freshly squeezed juice is applied to the stain, kept for no more than an hour, washed off. To enhance the effect, finely ground salt is added to the juice. So that you get a thick paste. It is applied to rust, but in no case is it rubbed. Otherwise, the gloss will be ruined.

ammonia and hydrogen peroxide

Sufficiently aggressive substances, so their impact should be short-term. To clean fresh rust, 5-7 minutes is enough. The ingredients are mixed in equal proportions, applied to problem areas.The maximum allowable exposure time is 10 minutes.

Helpful Hints

Experienced housewives recommend that before starting work aimed at eliminating stains in the bath, read a few useful tips. They will help to carry out cleaning manipulations as efficiently as possible and avoid mistakes:

before washing the yellowed surface, it is important to pay attention not only to the proposed cleaning materials, but also to what type of bath they are recommended (for example, what is suitable for a cast-iron bath may not be suitable for an acrylic one at all); the use of hard metal brushes is not allowed, as they provoke the occurrence of cracks, which will subsequently increase, worsening the appearance of the bathroom and significantly reducing its service life; it is undesirable to use bath cleaning products if they contain sebaceous acids (such products are prohibited for acrylic baths); it will be possible to prevent the occurrence of plaque if, after each bath, the bath is rinsed with warm water, thanks to which the remnants of detergents are washed off, preventing the formation of a film

Effective methods for clearing sewer blockages

A plunger is a rubber-tipped stick shaped like a large suction cup that can suck or push debris.

Using this simple invention, you can get the following results:

1. Prevent blockages.
2. Eliminate the causes of slow water drainage.
3. Assess the extent of pollution.

Recommendations for the use of a plunger:

1. Install the device so that its rubber part blocks the drain hole.
2. Draw a small amount of water into the bath (dry efficiency is reduced).
3. Make a few strokes by moving the handle up and down.
4. Check if the water is running out.
5. Flush out the trash.

If this did not help and the blockage in the bathroom did not disappear, then what to do? Use rope:

1. Insert it into the drain hole.
2. Push forward into the pipes and scroll at the same time.
3. When the voltage drops (the blockage is cleared), gently move the cable back and forth.
4. Remove and wash the product.

Chemicals

The modern chemical industry has taken care to make the process of removing blockages as fast and comfortable as possible.

Manufacturers vied with each other to produce tools for cleaning pipes from debris and deposits. The form of release can be varied:

• powder;
• gel;
• liquid.

The most common and inexpensive remedy is Mole - a domestic drug that perfectly eliminates odors, food debris and fat, and also breaks down fibers (hair, wool, etc.). Produced by different companies and may vary slightly:

• by composition;
• price;
• action time.

Compatibility with the type of pipes is usually indicated on the packaging. Here is a far from complete list of effective drugs:

1. Mister Muscle.
2. Bugs.
3. Pothan.
4. Tiret.
5. Flup.
6. Mole.

Folk way to clean the blockage: soda and vinegar

If there is no plumbing, no plunger, no cable, no purchased funds at hand and the bath is clogged, it is worth trying the folk method. This will require:

• ½ cup baking soda;
• ½ cup of vinegar;
• 1 liter of boiling water.

Follow these instructions:

1. Wipe the tub and metal drain ring dry.
2. Pour baking soda into the drain hole.
3. Pour vinegar into it.
4. Pour in boiling water after 1 minute.
5. After 2-3 minutes, turn on the water - it should flow freely.

Siphon cleaning

If, nevertheless, there is confidence that a necessary or valuable thing has become the reason for the slow draining of water, it is worth learning how to clean the siphon in the bathroom. Thus, it will be possible to remove what got into the drain and caused a blockage.

Siphon cleaning technology:

1. Lay a cloth under the siphon, put a basin or bucket.
2. Slowly unscrew the lock nut so that liquid does not rush out.
3. Remove the flask and discard the dirty water.
4. Remove any debris, small parts, or clods that are causing the problem.
5. Rinse the siphon and remove plaque.
6. Install the siphon.
7. Check tightness of connections.

Now, in case the bath is suddenly clogged, you will know what to do.

It is also worth watching a video on this topic:

Cleaning a cast iron bath

Old cast-iron baths are most often found in old houses. In most cases, their surface has multiple cracks.

In retail establishments, you can still buy cast-iron bathtubs of a new generation, the production of which uses innovative technologies and the latest materials. New bathtubs are more practical and resistant to temperature changes.

However, contamination can appear on both old cast-iron bathtubs and new ones. To clean such baths, it is recommended to purchase an oxygen-containing agent.

Laundry detergent

There is always a washing powder in every house. With this affordable tool, you can clean the surface of the cast-iron bath.

To do this, do the following:

1. 1. Apply a small amount of powder to the entire surface.
   2. The brush is moistened with water and actively brushed over the surface, whipping the powder into foam.
   3. Wash off the applied powder after 20 minutes.

Soda

Experienced housewives also share tips on how to wash the bath from yellow plaque with soda.

It is only important to consider that you will have to use two of its varieties at once:

• food;
• calcined.

For cleaning you will need:

1. 1. Mix both types of soda in equal amounts.
   2. Rinse the surface of the tub with warm water.
   3. Apply the prepared mixture to the moistened surface.
   4. After 30 minutes, mix vinegar with bleach, moisten the brush and treat the bath with this solution.

If you want the bath to be not only clean, but also shiny, it is recommended that at the end of such a manipulation, rub the surface with a woolen piece of cloth.

Ammonia

Everyone has ammonia in their first aid kit. It can also be a great help if you need to remove yellowness from the surface of the bath.

To get an excellent result, you need to follow simple steps in the following sequence:

1. 1. Two components are mixed: ammonia (1 tsp) and soda (1 tbsp).
   2. The prepared composition is applied, distributing evenly over the entire area of ​​\u200b\u200bthe product.

The smell from the plum: what to do?

If you feel that the drain smells bad, you need to take measures to eliminate this problem.

Make sure that the cause is not a dry water seal. Such a problem may arise if, for example, the owners of the apartment have not been at home for a long time. To deal with it, just skip the water. If you want to prevent bad odors, plug the drain before leaving.

Another option is to pour vegetable oil into the hole (this will require one glass). When you get back, add an alkali-based clog cleaner to the same place. It effectively dissolves fats.You can use regular dishwashing liquid.

• See if everything is in order with the pipes. If it turned out that the bend was broken, you need to give the pipe the correct shape, correct it.
• Rinse the siphon. This can be done with dishwashing liquid. It is recommended to use a grate with small holes for draining and clean it periodically.
• See if the outlet pipe reaches the liquid level in the siphon. If necessary, set it below.

Do I need to disinfect the bath and how

Enlightened visitors to the site may have a logical question: why talk about disinfecting plastic bathtubs if fungi cannot grow on acrylic. It really is. But don't forget 2 things:

• the bath after each use is simply rinsed (only cleanliness fanatics wash), and cleaned when free time appears. The fungus reproduces well on the plaque on the walls of the bowl (fats and various organic substances are an excellent nutrient medium). Therefore, if for some reason it was not possible to thoroughly wash the font for a long period (about a month), it is advisable to carry out its complete disinfection;
• the fungus reproduces well on silicone sealant, which seals the joints of the sides of the bowl with walls or tiles.

To protect relatives and friends from contact with harmful bacteria, you need to regularly carry out disinfecting measures. This can be done in several ways.

Method number 1. Domestos is bought, but only without chlorine, Acrylight, Santeh or Acrylon. To make sure that the purchased gel (paste) is suitable for an acrylic bath, you need to conduct a small experiment on a small inconspicuous area, because.Not all disinfectant containers have a warning label about the presence or absence of chlorine. If no changes are observed, then you can proceed to sanitation:

• the treated surface is rinsed with warm water, including the sealant;
• the gel is applied to a cloth or sponge;
• the entire surface of the bowl and the sealant are wiped. At the same time, it is impossible to leave a visible layer of the substance - a concentrated gel without chlorine can provoke the formation of stubborn stains;
• after 1-2 minutes, the applied agent is washed off with hot (about 60 ° C) water;
• the bathroom is wiped dry. If this is not done, limescale is actively formed in poorly washed places.

Method number 2. The bathtub is completely filled with warm water (20-25oC). Two bottles of "Belizna" with a capacity of 1 liter are poured into it with a bleaching agent concentration of not more than 7%.

Such a solution is left in the bowl for 10-15 minutes, after which it descends into the drain hole. Water is pouring into the bath again. The walls and bottom of the bowl are wiped with a sponge or rag. The water drains again. The bath is rinsed with warm water and then wiped dry. The disadvantage of this method is the need for additional processing of the sealant.

Method number 3. You can use a steam cleaner - hot steam not only kills germs, but also removes dirt, restoring the shine to the surface. This type of treatment is desirable to carry out every six months. The only requirement is that you cannot stay in one place for a long time. You can melt the surface.

Removal of other types of contaminants

How to wash the bath from potassium permanganate and brilliant green?

These two components are the most common types of pollution in the bathroom.Even a weakly concentrated solution of manganese will leave dark marks on the surface of the product.

A drop of brilliant green solution will also add color.

Manganese is washed with a solution of hydrogen peroxide and lemon (or fresh lemon juice), they will not only quickly discolor the stains that have appeared, but will make the bath shine.

We remove the greenery with alcohol. However, if the surface of the plumbing is made of acrylic, then alcohol may be powerless before contamination.

How to wash the bath after repair?

In order not to have to deal with its consequences on a soiled bathroom upon completion of the repair work, the product must be protected from building materials. If trouble has happened, then you can use the following means.

Any solvent will help to wash the paint bath (for example, white spirit)

It is important to work quickly so that the paint does not have time to soak into the surface.
Rinse off dust deposits with warm water, then clean with citric acid.

How to wash the sealant from the bath?

Sealant is another type of bathroom contaminant. It is used to ensure the reliability of joints and seams. Sooner or later the question arises of how to wash the bath from this material.

In this case, you can use folk methods using table salt, but it is better to buy professional products specifically for such cases.

How to clean an old bath?

If the bath is far from being the first year, then pollution appears on it very quickly. They penetrate into all microcracks that have formed on the surface over time.

Not all cleansers can easily restore its original appearance. Better, of course, to replace the plumbing. But if this is not possible, then soda ash will help.The procedure for working with it was described above.

Which tool to choose

It would seem, well, what's the problem here - household chemical stores offer a variety of cleaning products for a variety of purposes, choose any. Moreover, cast iron - for that it is cast iron, it will withstand everything. But it was not there! It is far from the same as cleaning a cast-iron bath - and the owners of such fonts will confirm this from their own experience.

By itself, cast iron is really not afraid of acid, intense friction, chips, or scratches. But on top it is covered with enamel.

Enamel is a smooth coating that is made using a special technology using zirconium salt. And zirconium is very sensitive to corrosion. Because one deep scratch - and the appearance of rust can not be avoided.

That is why, if the detergent for the cast-iron bath is not chosen correctly, or it was washed using wire brushes, the coating becomes uneven, loose, loses its luster and attracts dirt even more, literally absorbing it.

By the way, modern manufacturers of cast-iron bathtubs have long since replaced zirconium salts with titanium salts - for such a bathtub it really doesn’t matter how to wash it and scrape it, it really is almost invulnerable.

If you have old cast iron bath sample, then when choosing the optimal cleaning agent for it, the following points should be considered:

1. If you want to maintain or restore the gloss and smoothness of the enameled surface, you should forget about any chemicals once and for all - bleach and acids are excluded. The same applies to powders with abrasive particles.
2. If you need to wipe off limescale, dust soap will do.
3. Rust is removed with vinegar essence, oxalic acid or turpentine.

Well, if you are looking for a way to whiten a cast-iron bath, then ordinary stove ash will help you. Oddly enough, this black substance can make an old cast-iron bath snow-white without much effort on your part. In a word, you can use all the tools that our grandmothers used regularly - nothing the best for today modern technologists have not invented cast-iron bathtubs.