4 life hacks to help clean the floor from dirt

How to wash difficult stains

In the fight against complex stains, special means of narrow (point) action will help, but sometimes you can get by with simple, folk remedies.

But it is important to remember the features of the materials. For example, if a tile can be thoroughly rubbed with a brush (especially one with a rough surface), then this number will not work with laminate and parquet.

With complex stains, special equipment will help to cope.

In the last two cases, you need:

• use brushes with soft bristles only;
• do not use aggressive cleaning agents;
• do not rely too much on the universality of folk methods (they are designed for simple, unpretentious materials).

How to wash whitewash?

The most difficult thing is to wash the whitewash from the floor covering. In order to effectively get rid of white stains, it is necessary to change the water frequently and rinse the rag or mop well. You can effectively get rid of traces of whitewash with the help of such folk remedies.

Whitewash remover	How to act correctly?
rock salt + vinegar	The first time you should wash the floor with clean water, then collect new water in a bucket and pour five tablespoons of rock salt into it. Salt water is great for getting rid of traces of whitewash. At the end of the cleaning, wash the floors with a weak solution of table vinegar.
Sunflower oil + vinegar	dissolve a small amount of vegetable oil in a bucket of warm water in a ratio of 100: 1, respectively; thoroughly wash the floors from lime residues; after that, make a new solution: dissolve a little table vinegar in warm water - and rinse the floors well again; Finally, wipe the surface with clean, cool water.
Potassium permanganate	dilute this amount of potassium permanganate crystals until the color of the water becomes bright crimson; thoroughly wash the floors with the resulting solution; wipe the floor surface with clean water. But this tool can not be used on surfaces that are varnished, because stains will remain.
Kerosene	Whitewash, which has already dried well on the flooring, can be washed with kerosene. For this you need: add 150 grams of kerosene to 5 liters of water; thoroughly wash the floors, and in places where whitewash or putty has dried, rub them with a sponge dipped in kerosene; in order to eliminate the unpleasant odor, wipe the floors several times with clean water with the addition of a glass of table vinegar.

How to remove construction dust

The repair is over, but the apartment or house is covered with a layer of fine ubiquitous dust. Many people are familiar with this picture. How to remove construction dust? Let's just say that you have to clean more than once. You will need a good spray gun and a powerful vacuum cleaner, a bucket and many, many rags. Vacuum cleaner is better to use construction, with long hose and telescopic nozzle. Household is also possible, but he, most likely, will not survive such a load. After cleaning, it may have to be thrown away, as fine dust clogs the engine and it burns out.

It's good to have helpers

If there is an air humidifier with an ionizer, instead of a spray gun, you can adapt it. But it must be left in each room for a couple of hours. Too long if there are several cleaning rooms.

Cleaning the floor from dust

Close the windows / doors in the apartment, then you can start cleaning construction dust. If the ventilation works well, you can cover it for the duration of the cleaning. Let's say right away that you will have to repeat everything more than once, you need to do cleaning in all rooms, moving from one to another. The methodology is this:

• We adjust the spray gun to the finest mist, spray a certain amount higher into the air. Water dust settles, capturing dust particles that are in the air. A wet crust forms on the floor. If the layer of dust on the floor is significant, it is better to wait until it dries and vacuum it up.

• We leave the room for at least an hour - so that the water dries.We make sure that there is no draft that can raise the settled dust into the air.
• The vacuum cleaner is in the next room, and we bring a hose with a nozzle into the room, we collect dust with a vacuum cleaner.
• We repeat the “event” until the air becomes relatively clean and there is a minimum of dust on the floor.

Next, you need to clean the floor. If the air has been sufficiently purified and after the next vacuuming there are no dusty tornadoes in the air, you can not spray water dust. We take more water, a lot of rags. My gender. The cloth and water should be changed as often as possible. If possible, it is better to rinse the rag in running water each time. You run into the bathroom, of course, but cleaning is more effective this way. Do not try to wash completely yet. The main task is to remove the volatile fine fraction. It is removed only with water and a rag. If you have a washing cyclone vacuum cleaner (with a water tank through which air is passed and the sucked dust settles in the water), you can adapt it. He does an excellent job - quickly and efficiently.

For information on how to make a cyclone-type water filter for a household vacuum cleaner, see the video below.

Removing debris from walls, windows, doors

Then we clean the vacuum cleaner, wash the brush or put on a clean / new one. The second option is preferable. We remove dust from the ceiling and walls with a vacuum cleaner. You can go through several times. Then the floor again, then the windows and doors. Don't forget to wipe the top of the doors. There is a lot of dust there. When the doors are closed, it is sprayed throughout the room.

To clean the floor after repair, you do not need expensive funds

After removing dust from all vertical surfaces, we wipe the floor again, washing the rag often. If there are white stains on the doors, windows, add vinegar or citric acid. You can drop a little dish detergent. After processing with such a composition, there should be less divorce.

How to wash the floor after repair

While washing the floor with just water, it seems that the dust is simply smeared. There are white spots all over the floor. When you have already cleaned the walls and ceiling, you can try to wash the floor more efficiently. Add to water:

• A little bit of vinegar. Regular, food alcohol - 6-8%. On a bucket of water - from half a glass.
• Salt. On a bucket of warm water with 1/3 cup or so. Stir until dissolved.

• A couple of tablespoons of vegetable oil.

To get rid of white streaks on the floor, you can try all three products in turn. Each "additive" - ​​salt and vinegar - works, but somewhere one turns out to be more effective, somewhere else. Depends on the composition of the dust (its source, to be precise). For faster results, you can immediately salt and vinegar. They don't interfere with each other. Vinegar has an unpleasant odor and can be replaced with citric acid.

These simple home remedies help to quickly remove dust from the floor after repair and get rid of streaks. In principle, as soon as the layer of dust on the floor has become very small, you can add salt and vinegar. Divorces will be less, but the water must be changed often. Water with vegetable oil will help to finally remove white plaque from the floor - linoleum, laminate, tiles. It's so weird, but it works. Check. And the floor is non-greasy and non-slip. So, to clean the floor after repair, you don’t need some kind of miracle remedy for big money.

How to remove the fungus?

But if the cause of dirty seams lies not in dust and detergent residues, but in mold, you should use slightly different methods:

If it has just begun to appear, then you can prepare your own disinfectant from bleaching gel and ammonia with water. For this, 100 g of "Whiteness" and 50 g of ammonia are mixed. This solution is poured into liter of hot water, and then applied to the fungus with a spray gun and left for half an hour. After this time, the seams are wiped with a damp sponge and washed with warm water. Then they wash again with water, but with the addition of vinegar to it. based on liter of water 100 g of 9% vinegar.

It is necessary to clean the seams between the floor tiles from the fungus in a timely manner. Otherwise, the mold will begin to grow and can not only disfigure the entire room, but also cause serious harm to health.

How to clean an unpainted floor

In order to wash a regular wooden floor without staining, you need to dissolve a little soap or alkali in warm water. It is wiped with such a solution and carefully rubbed with a brush with a hard bristle. Warm water with washing powder or baking soda is also perfect. Three tablespoons of soda are required per liter of water. A bare broom or root brush can be used as a wiping tool.

Soapy water is great for unpainted floors.

If there are serious stains on the surface, then abrasive methods can be used to remove them, which are unacceptable in the case of a painted floor. So, first wipe it with a hard-bristled brush, then make a solution of sand and lime (in a ratio of 3 to 1) and rub the floor with it. Wash off the solution with warm water.If the spots still remain, then use white clay or wet sulfur. Apply it on the spots and leave overnight. Wash off with warm water in the morning.

Grease stains on an unpainted floor are removed with gasoline, then sprinkled with starch and ironed through a napkin. You can also make a solution that will include white clay, gray clay and vinegar. Cover the stain with this solution and leave overnight. In the morning, rinse the surface with warm water.

Carpet features

A decisive role in the selection of a cleaning method is played by the characteristics of the product itself.

Material

It is quite obvious that the material from which the rug is made determines what substances and temperatures it can withstand. Carpet can be made from different materials.

Synthetics are the most common and most practical option, since synthetic threads are unpretentious. To clean them, simply vacuum them.

In the case of complex stains, it is permissible to use almost any means, with the exception of solvents. Most industrial chemistry is designed specifically for synthetic samples.

Such tracks can even withstand washing if their base is not glued. The adhesive base may only be dry cleaned.

Wool is a finicky coating that requires careful handling. Soda and starch are suitable for cleaning. Sometimes (not more than once a year) the woolen fabric can be wiped with a mild soapy solution on both sides. Do not use salt and bleach, as well as take out in the sun.

Silk is an even more finicky material to care for. It absolutely does not accept moisture. Powerful mechanical action destroys delicate fibers, so you should be careful.Steam generator treatment, brushes, soap, solvents, chemicals with chlorine are prohibited.

Best care method: Gently shake out. If there are any stains, then it is permissible to wipe this area with suede soaked in a weak vinegar solution.

Viscose - will not tolerate washing and strong friction. Preparations with chlorine and alkali spoil the product.

For constant cleaning, a vacuum cleaner without a turbo brush is suitable, and for more thorough cleaning, special foaming compounds are suitable.

Fur - natural fur bedding is the pride of the owner. But there is a lot of trouble with them: they cannot be washed and vacuumed, almost all cleaners are prohibited.

To remove debris, it is advisable to gently shake them out, you can treat them with soda. To remove sewage, a recipe with gasoline, ammonia or vinegar is suitable.

Pile length

This setting determines which kind of cleaning will be applied.

1. Short - easy and quick to clean. Moreover, you can use any means (including folk) and equipment that are available to you.
2. Long - cleaning a carpet with a long pile is not the easiest task, because particles of debris, pet hair and hair are clogged between the threads. Such products cannot be actively rubbed and vacuumed at high power: the base can be damaged. In addition, if you wet the coating abundantly, it will be difficult to dry it, and this increases the risk of mold and unpleasant odors. The most optimal approach would be gentle knocking out and processing with foam that pushes out dirt. For particularly difficult places, you can walk with a steam cleaner.

Color

In order not to spoil the appearance, it is recommended to select a method taking into account the color of the product:

• dark and colored - for such rugs it is not recommended to use any white powders, as they leave ugly stains. It is allowed to resort to mixtures based on vinegar, ammonia or tea;
• light and white - soda and starch, as well as soap, are useful here. Of course, any coloring substances like tea leaves are prohibited. Lemon juice is also undesirable as it leaves yellow marks.

Ratings

Ratings

• 15.06.2020
• 2976

Which is better to choose a water heated towel rail: manufacturer rating

Types of water heated towel rails: which one is better to choose, rating of manufacturers and review of models. Advantages and disadvantages towel dryers. Features and installation rules.

Ratings

• 14.05.2020
• 3219

Rating of the best wired headphones of 2020

The best wired earbuds for 2019 A brief overview of popular devices designed for a variety of purposes. Pros and cons of budget gadgets.

Ratings

• 14.08.2019
• 2580

Rating of the best mobile phones for games

Rating of the best mobile phones for games and the Internet. Features of choosing a gaming smartphone. Main technical characteristics, CPU frequency, amount of memory, graphics accelerator.

Ratings

• 16.06.2018
• 862

How to clean ceramic tiles from grease and dirt?

If snow white tile on the floor no longer pleases with its fresh look, then use the following tools:

• Vinegar.
• Lemon acid.
• Ammonia.
• Dishwashing liquid.
• Soda.
• Chlorine or "White".
• Washing powder.
• Kerosene.

Use the above tools as follows.

Vinegar

Dilute 0.5 cups of vinegar in 4 liters of water. Rinse the floor with the solution.Rinse the cover with clean warm water and dry.

Lemon acid

Gently dip a kitchen sponge in citric acid and treat problem areas to wash the tile on the floor from stubborn dirt. Then rinse the area with clean water, pat dry.

Bleach

For snow-white tiles, use ordinary bleach or "Whiteness". If bleach powder, then dilute it in water according to the instructions. Pour the solution into a spray bottle, spray on the surface. After 5 minutes, brush the problem area with a brush. Rinse the floor with plain water, wipe dry.

washing powder

1. Remove spill stains with detergent paste:
2. Pour washing powder into warm water in a ratio of 1:1.
3. Rub the stain with a dust cloth.
4. After 5-10 minutes, wipe the area with a soft sponge and wash the floor with clean, warm water to remove any detergent residue.
5. Repeat the process if necessary, then wipe the floor dry.

ammonium chloride

Ammonia will remove mold from the tile. It will also help to wash the tiles on the floor from ingrained dirt:

1. Prepare a solution: ammonia - 1 part, water - 1 part.
2. Wear rubber gloves to protect your hands.
3. Take a soft brush and scrub the tiles with the solution.
4. After treating and removing mold, rinse the surface with clean water.

Kerosene

Kerosene will remove rust and building material stains. Put on rubber gloves and soak a rag in kerosene. Wipe problem areas with a cloth and rinse the surface with warm water. Repeat the process if necessary.

Helpful Hints:

Rough, embossed or dark ceramic tiles try to wash off the glue (grout) as soon as possible.Use vinegar solution for this purpose: for every liter of water - 50 ml of vinegar

Thoroughly wipe the contaminated areas with a solution, pay special attention to the joints between the tiles. After treatment, rinse the surface several times with warm water and dry with a soft cloth.
If there is no special tile brush, then remove the dry grout with a piece of light wool or felt

After removing the grout, wash the floor with a vinegar solution.
Glossy tiles after grouting cannot be cleaned with abrasive powders and metal brushes, as it will lose its luster. Use only brushes with soft bristles and liquid products that do not damage the surface of the tile.
Do not use household chemicals designed for cleaning gas stoves and plumbing to clean tiles. Before using this or that “chemistry”, be sure to read the instructions for use.
To prevent damage to the joints between the tiles, during cleaning and surface treatment, coat them, for example, with epoxy paint. And remember that unprotected seams can be damaged by solutions containing acids.
In order to dry the tiles, use microfiber or terry (bamboo) towels.

More more helpful tips You will find in a separate article about the proper care of tiles.

Marble and granite

Marble and granite flooring is durable, but it is important to know how and with what to wash the floor at home. Such surfaces quickly stain, so cleaning should be done immediately after spilling orange juice or vinegar.

How to wash floors:

1. For best results, wash marble or granite with Vim liquid dish soap.When using a new floor cleaner, always test it on an inconspicuous area.
2. Since marble and granite are natural materials, they require special attention. The problem with cleaning is that these surfaces do not have exactly the same properties as ceramic tiles and can be damaged by common cleaning products. What can be washed? In order to clean the house, it is necessary to clean it with the help of LEM-3 (BELLINZONI, Italy, neutral in relation to pH). The concentrated product is poured into cold water. How to clean floors with a mop: it should have a 100% microfiber nozzle, movements should be short, overlapping. After the procedure, it is necessary to drain the dirty water, rinse the mop and walk along the flooring with clean water. Then you need to open windows and doors and allow the marble or granite to dry with natural ventilation.

Always check the safety instructions and recommendations on any product you use to clean marble or granite and test it on an inconspicuous area first.

Since granite and marble are natural materials, there are also some items that should not be used due to the risk of damage and scratches.

Do not wash the floor with salt. This is an abrasive product that can damage such flooring. Ceramic cleaners, vinegar, or other alkaline products should also not be purchased to clean marble surfaces. Hydrochloric acid should not be used either.

If it is necessary to remove dirt and dust, use the vacuum cleaner carefully, wheels and hoses may scratch the material.

How to clean parquet floor

Dry cleaning is recommended for parquet flooring.You can remove dust with a vacuum cleaner with a soft brush that will not scratch the parquet. They wash the floor infrequently, trying not to pour water and not make puddles. This should be done only as necessary, when the dirt is not removed by the dry method.

General cleaning is carried out once a year, in dry weather, when you can fully ventilate the apartment and quickly dry the floor. A hygroscopic washcloth is taken, which can be wrung out well so as not to leave excess water on the parquet.

Mop

The parquet is washed with a mop that does not have sharp hard edges. Nozzle - microfiber, which has a high hygroscopicity, quickly absorbing moisture. Models with a mechanical wringer are ideal, immediately removing excess water.

Training

The first step in cleaning parquet is to wipe the floor with a damp cloth to remove dust and reveal dirt that cannot be easily removed.

Stain removal

Even the cleanest owners have stains on the floor. Before proceeding with the removal, you need to understand what they were formed from in order to choose the right method of removal.

Drink stains can be removed with a cloth soaked in a solution of baking soda.

Fat

fresh oil stains wash off with detergent, dissolving it well in water. Old stains are removed:

1. Solvent based on petrol. Then wash with soapy water.
2. Cool the area of ​​the floor strongly (using ice from the refrigerator), remove the fat layer with a sharp knife. Then apply a clean cloth and iron.
3. Pour a layer of starch over the stain, cover with a thick cloth and iron several times.

Grease stains must be removed quickly so that the contamination does not penetrate deep into the wood.

Ball pen

Traces of ink are washed off with detergents, which are previously diluted in water.A weak solution of vinegar or alcohol also removes stains from the floor. from ballpoint pens.

Urine

When removing urine, it is necessary to remove not only the stain, but also get rid of the smell. Urine flows into the joints between the elements of the parquet, puddles must be wiped immediately so that the wood is not soaked. The rag is moistened with a solution of alcohol and the floor is wiped. To get rid of the smell, the cloth moistened with alcohol is left on the floor until it dries.

Gum

Any package from the freezer is placed on the sticky and smeared chewing gum. When the chewing gum hardens, carefully remove it with a knife.

Tar or resin

Such spots are first frozen, then the contamination is scraped off with a knife. If necessary, use a solvent for resins.

the washing up

The parquet is washed with water at room temperature. Use rags that can be squeezed well. They begin to wash the floor from the walls, without pressing on the mop so that the water does not absorb much. A few rules:

1. Scouring powders with abrasive components are not used.
2. Do not use detergents for washing windows, dishes, only for parquet.
3. Stains are cleaned in advance.
4. The washcloth is always wrung out as much as possible.

Despite the dislike of parquet to water, you need to wash the floor at least once every 2 weeks. The accumulation of dirt, the penetration of contaminants into the cracks spoils the appearance of the coating.

Completion

Finish wet cleaning with a second pass over the floor with a semi-dry rag to remove stains. Then the premises are thoroughly ventilated to reduce humidity and dry the parquet. Only after that they arrange the removed furniture, spread carpets, rugs.

Washing vacuum cleaner

Even the best washing vacuum cleaners do not completely collect water after cleaning, the contact of parquet with water is long. Washing vacuum cleaners for it is better not to use parquet floor cleaning.

Dry cleaning

Dry cleaning is the most preferable for parquet. The floor is wiped with a dry mop with soft nozzles, sweeping away dirt and dust. Many manufacturers vacuum cleaners offer special models for dry cleaning of parquet, equipped with soft brushes. Leaders in quality are vacuum cleaners from Karcher, Bork.

Steam mops and steam generators are not used for most types of parquet flooring. High pressure and hot steam are the enemy of tender wood, the joints expand. White stains appear on the varnish, the wood darkens.

Causes of pollution

Before proceeding to the description of the means of combating pollution between the seams, it is necessary to understand the reasons for their appearance.

Dirt between tiles on the floor appears for the following reasons:

• Particles of building and finishing materials get into the cracks during repairs, both in the bathroom and in other rooms.
• The cause of contamination can be the remnants of detergents, as well as particles of dirt from the water with which the tiles were washed. After the moisture dries, all debris remains in the seams and is pressed.
• Compacted dust can also cause heavy soiling and darkening of the joints.
• The fungus in the tile joints creates not only the appearance of a dirty floor, but also causes an unpleasant odor in the room.

The specific method of cleaning the seams should be chosen depending on the cause of their contamination. It is also worth noting that often the seams darken simply from time to time, for example, when the tile has not been changed for more than 10 years. But in all these cases, the floors can be reanimated by the same methods.

How to wash whitewash from the floor after repair

It can be whitewash, old wallpaper, paint, plaster, and so on.Putty is a powder building material that is also used for interior decoration. Its main purpose is to level surfaces.

Removal of old putty can be partial or complete, therefore, before removing the old putty, it is necessary to inspect the entire surface for the strength of the coating. If the putty has peeled off or cracked in some places, then the problem areas must be cleaned using a scraper or spatula, primed well and puttyed again.

If it is not possible to reanimate the old putty and you need to completely clean the surface, then you should acquire the following tool: a spatula, a hammer and a chisel, a puncher with a lance or spatula, a grinder with a diamond wheel.

2 How to remove old putty - a common technique

Before removing the putty, preparatory measures should be taken, because a large amount of dust and dirt is generated during work. All furniture must be taken out, the floor should be covered with polyethylene or newspapers, a sheet soaked with water should be hung on the doorway.

First of all, you need to try to determine the statute of limitations of the old putty, the approximate thickness of the layer: the amount of work will depend on this. If the previous coating is poorly removed with a spatula or scraper, then you need to prepare a starch solution. Two tablespoons of starch are placed per liter of water, after which the solution is thoroughly mixed.

The resulting mixture is applied to the surface with a brush, roller or spray gun and left for about fifteen minutes to allow the liquid to seep into the pores. After applying the solution, the putty should become loose. Then, using a hard metal spatula, it is necessary to remove the old coating from the surface to be treated.

For convenience, you can conditionally divide the surface into sections and sequentially process them one by one. On the seams between the slabs and ceilings, the putty should be removed with a chisel and hammer, since in such places it is the strongest.

After that, you need to wash the surface with warm water. But before you wash the putty, you need to remove its remnants with sandpaper.

3 How to remove old putty if the usual method does not help?

If the layer of old putty is thick enough, then it is better to use a puncher. To do this, a spatula or a chisel is inserted into the cartridge, and the operating mode of the puncher switches to the “blow” position. So the whole layer is broken.

An alternative would be to use a grinder with a diamond wheel. First, a notch is made on the surface, and then a layer of old putty is ground off. To do this, the tool must be held in such a way that the disk is parallel to the surface to be treated.

This method is the fastest, but at the same time very dusty. When performing this type of work, you should use a respirator and goggles so that dust does not penetrate the lungs and does not irritate the mucous membranes of the eyes.

Before starting the process, it is necessary to determine the location of the wiring and, if necessary, turn off the current supply. During work, you need to take breaks and ventilate the room. Before applying a fresh layer of putty, the surface must be thoroughly cleaned and well primed.

ask in the household, there are special washes for such cases, ask the consultant, you must choose a wash for her!

Ceramic tiles Sergey……

• 14 replies
• 3 713 Views

• 03 April 2012 — 01:16
• Last message: Bonis

Helpful Tips

Cleaning the joints between tiles on the floor is a necessary and responsible task, but even it can be done with pleasure. Choosing folk cleaning methods, you can add essential oils to water tea tree or lemon. They will not only allow you to saturate the air with a pleasant aroma, but they are also additional fighters against mold and fungus.

All work is best done with gloves, because even from prolonged contact with mustard powder and soda, not to mention aggressive cleaning products, the skin of the hands may suffer. During work, it is better to ensure the flow of fresh air into the room.

Tiling joints should be cleaned at least once a month. And in order to make them less dirty, you can add lemon juice, vinegar or a couple of tablespoons of ammonia mixed with aromatic oils to the last water for mopping.

These practical tips will help you quickly and easily get your tile floor in perfect order. Having resorted to them, you can forget not only about the dirt on the floor, but also about fungi and mold.

See the video below for practical tips on how to clean the grout between tiles on the floor.