Review of infrared heaters "Almak"

The sequence of installation of an infrared heater on the ceiling

On suspended or wooden ceilings, installation is carried out quickly enough. It is enough to screw in the hooks on which the unit is hung. For a concrete ceiling, the connection is made using a perforator.

Options for mounting a heater with a thermostat:

1. First, the thermostat is connected to the heater. From the circuit breaker you will need to run two wires. One of them is zero, and the second is phase. Given the marking, you need to connect the thermostat to the device. We open the connection socket in advance.
2. If there are more than two heaters, then a parallel connection is made. In general, the connection sequence is preserved. First, wires are connected from the switch to the thermostat, and then to the heater.
3. It is more difficult to connect equipment with a magnetic starter.This is how industrial heaters are connected.

For safe operation of the device, it is necessary to carry out grounding. A special cable is connected to the terminal

Particular attention should be paid to the choice of installation site. It should provide maximum efficiency.

Possibilities of using IR emitters Almak

IR emitters Almak are used for heating industrial and domestic buildings, as well as unheated premises. The main areas of application of the infrared equipment of the company are:

• Primary or additional heating of residential apartments and private houses. Almac household ceiling infrared heaters are suitable for rooms with a ceiling height of at least 2.7 m. Models with a built-in thermostat operate in a completely autonomous mode, maintaining a comfortable temperature in the room. To heat a well-insulated room, an emitter equal to the ratio of 70 W per 1 m² is required.

Dachas and country houses. The equipment has a high fire safety. Sensors are installed that block the operation of the device in case of overheating. Degree of protection IP 24. This eliminates the need to use grounding when connecting to the network. For cottage-type rooms, with poorly insulated walls, a performance of 90 W per 1 m² is sufficient.

Garages, poorly insulated workshops, workplaces. An adjustable ceiling mount bracket is used. You can set any angle of radiation, which is very convenient for local heating. The panels are installed directly above the heated area. The scattering angle of infrared radiation is 20 and 40°C.

Office premises and shopping complexes.The area of ​​heating the room with one heater is 15-20 m². The company's temperature controller, designed to be connected to a heater, ensures high safety. Analyzing the indicators of air heating, automatic control of the room temperature is carried out. The calculations take into account the coefficient 100 -120 W/m². Another advantage of the panels is that Almac ceiling heaters with IR radiation are produced not only in classic white, but also in colors according to the RAL catalog.

Industrial premises. The calculation of the power of the required number of IR devices is carried out taking into account the ratio of 100-150 W / m². Movable brackets allow you to adjust the required installation height. The housing is made exclusively from stainless materials, so you can install radiant panels in workshops, warehouses, greenhouses, winter gardens, etc.

The performance of one emitter, depending on the model, is 500 -1500 kW. Voltage 220 V, heating area from 5 to 30 m². Other technical specifications are given in the instruction manual.

Infrared heaters Almak

Heaters of this brand are mastered by Russian manufacturers, the company specializes in the production of infrared ceiling heaters using innovative technologies. In the production of heaters, only modern materials of high quality are used.

The company's developers managed to achieve high quality products, which are reliable, have a long service life without failures. Immediately after serial production, infrared heaters began to be in demand among the population of Russia.They appreciated the new type of heaters with good performance. Infrared equipment has a stylish design, modern materials and high-quality assembly.

The principle of operation of infrared heating devices is based on the heating of objects in the room, the heat from which is transferred to the air. The modern look of heaters differs from previous models with infrared radiation. Infrared rays are not absorbed by the air, all the heat is given off to the surfaces, due to this it is comfortably distributed over the surfaces in the absence of drafts.

The device can be attached to the ceiling, it will distribute heat, the device can be used as an additional or main source of heat in the room. Very often, such devices are used to supplement heating in a large room. Using the Almak infrared heater, you can make the heating point or zoned, exactly the part of the room where heating is needed more.

An important advantage of the Almak infrared heater is that it does not burn oxygen, so the air does not dry out, heat is distributed evenly and completely over the entire area.

When using infrared equipment, there is no air convection, so there is no dust, and this is very important for health

Ceiling infrared heater: installation and connection

Infrared heaters are mounted quite simply with self-tapping screws. If the ceiling height exceeds 3 m, then brackets help. Hangers are often used for high ceilings. There must be a minimum distance of 50 cm from the occupant's head to the appliance.

Installation recommendations:

1. Do not install the device near flammable objects. Electrical cables should be laid on a non-flammable surface.
2. You can turn on the device only after the connection is completed.
3. Suitable models are selected for rooms with an aggressive environment.
4. Fasteners should be performed only on special holes designed for this. The connecting element must not come into contact with the heater.
5. The distance between the surface of the installation place and the heater should be 3-6 mm.

In addition, do not install the device in crowded places. It is better to move the installation site a little to the side. For a residential building, panels with a power of no more than 800 watts are purchased.

The optimal hanging height of the device is 2.5-3 m. If the unit is installed on the wall, the heater's productivity is reduced by approximately 30%. When wall mounting, care should be taken to insulate the device, as the panel heats up to 200 degrees.

Pros of using

During the operation of ceiling infrared heaters, the distribution of heat occurs differently, according to the solar type: it is not the air that is heated, but the surrounding objects, which, in turn, also become heat sources.

The advantages of infrared heaters include:

• high level of efficiency, which reaches 97%;
• the appliance starts producing heat immediately;
• small size and the ability to install heaters on the ceiling, which saves space;
• infrared models do not need water, electricity is enough.

In addition to the advantages, infrared heaters also have a number of disadvantages: for example, with prolonged exposure to a person, they can cause headaches like from sunstroke.

It is important to know: it is almost impossible to overheat the heater plate, but it is better not to leave flammable objects near the device, for example, paper garlands.

Features of Almak infrared heaters

An infrared heater, by heating the surrounding objects, leaves the humidity and chemical composition of the air in the room unchanged.

Almak devices operate on the basis of generating infrared radiation that carries heat. Reaching the surrounding objects, this radiation causes them to heat up. As a result, they become independent sources of heat, which is released into the atmosphere of heated rooms. Under the action of infrared radiation, not only interior items are heated, but also walls with floors, becoming excellent sources of heat.

Infrared heating causes mistrust among many consumers. Despite this, it is characterized by high efficiency and economy, allowing you to save on electricity consumption. Evidence of this was the appearance of domestic infrared heaters "Almak", produced by the company "Company Novy Vek". These devices work on the infrared principle of operation and have good characteristics.

Where are domestic infrared heaters "Almak" used?

• In residential premises.
• In industrial premises.
• In office and administration buildings.
• In shops and trade pavilions.
• In buildings and premises for economic purposes.

With proper operation, the infrared heater is not capable of harming the health of any member of your family.

These devices have received excellent reviews on Internet forums.Users actively use this heating equipment in buildings and premises for various purposes, getting at their disposal an excellent source of heat. The manufacturer himself claims that such heat sources are close to natural, since our planet is heated by the sun in a similar way.

What are the features of Almak infrared devices?

• The minimum thickness of the cases - modern production technologies make it possible to produce heaters with a thickness of only 3 cm.
• Fast and uncomplicated installation - it is enough to hang lightweight heaters on special mounting hooks.
• Easy to connect to the mains - for this special electrical pads are used.

In addition to everything, the devices of this manufacturer have many certificates confirming their effectiveness and complete safety in all respects.

It must be understood that these devices will be safe only if the operating rules and installation rules are fully observed. Detailed instructions on these issues are included in packages with equipment and published on the official website of Almak.

Almak infrared heaters create a comfortable atmosphere for people and pets in heated rooms. Be sure to note the optimal distribution of heat - the warmest areas are near the floors, and not near the ceilings. Thanks to this, heat consumers will never get cold feet, as is often the case when using classic convection heating with hot air.

Model range of Almac heaters: features of each option

In total, seven models of Almak heaters have been developed. Different options differ from each other in terms of power.So you can choose the perfect option for any room. The thermostat will handle the fluctuations.

Model range of Almac heaters

• IK-5;
• IK-8;
• IK-11 with thermostat
• IK-11;
• IK-13;
• IK-16;
• Armstrong.

Model IK-11 with thermostat has a wide range of applications. It is used for residential buildings, in production, in the office, retail outlets. In appearance, the heater is a standard fluorescent lamp. It is quite compact, so it will not spoil the interior.

The IK-5 model has a low power, but is able to heat an area up to 10m2. But it is better to use this device for small rooms. Another low power model is IK-8. It can be placed in a small room or as an additional light source.

Model Almak IK-13 has an average power of 1300 watts. Suitable for medium sized rooms. In this case, the ceiling height should not be more than 3.5 m. IK-16 has a power of 1500 watts. This unit is considered the most powerful among all models. They are used for large rooms.

The Armstrong type model is used in rooms with suspended tiled ceilings. Due to its dimensions, the heater is ideal for this type of ceiling covering. One plate is removed, and the device is mounted in its place.

Installation and installation

heaters Almak ceiling type

The suspension height must be at least 1.5 meters, so you need to take into account the height of the ceilings in the room, with low ceilings short brackets are used, it is best to order them separately.

It is better to entrust the connection of the Almak heater to those who know all the intricacies of the connection. The specialist will perform all the work, strictly observing the necessary requirements specified in the installation instructions.It must be remembered that the device belongs to fire hazardous equipment, and any contact with flammable materials can lead to fire.

Heating devices during the period of operation can absorb moisture, therefore, periodically the heater must be turned off and wiped.

Model overview

In the manufacture of only modern high quality materials are used, and the model range is regularly expanding.

Developers regularly make improvements and adjustments, which allows the company to offer only high-quality products. Also, the advantages include modern design, a wide range of models, in which it is easy to find the optimal model, and high-quality assembly, thanks to which the device will serve for a long time.

The company offers customers several color options: white, silver, yellow and wenge (the color of a certain wood).

It is worth noting: when choosing an IR heater, you need to pay attention to all the parameters in order to choose the most suitable model.

Among the Almak models stand out:

1. IK-5: the most low-power model, which is suitable for heating rooms up to 10 square meters. m. Its power is 0.5 kW, dimensions 73 * 16 * 3 cm, weight slightly exceeds 1.5 kg.
2. IK-8: suitable for larger rooms up to 16 sq. m. The model has dimensions of 98 * 16 * 3 cm, weight 2.3 kg and a power of 0.8 kW.
3. IK-11: designed for rooms up to 20 sq. m. It has a power of 1 kW, dimensions 133 * 16 * 3 cm, weight 3.3 kg.
4. IK-13: has dimensions of 164 * 16 * 3 cm, weight is almost 4 kg and a power of 1.3 kW. The model is designed for space heating up to 26 sq. m.
5. IK-16: the most powerful model, the power of which is 1.5 kW.With its help, you can easily heat a room up to 30 square meters. m. It has dimensions of 193 * 16 * 3 cm, weight exceeds 5 kg.

All models are designed for rooms with a ceiling height of no more than 3 meters: when installed at a higher height, infrared rays will not be able to reach the floor, which will significantly reduce their performance. Standard 220 V power supplies are suitable for power supply.

Also, models can be connected with a thermostat for complete control over the temperature.

Infrared heaters are an excellent solution for a country house, a city apartment, and small offices. They allow you to quickly warm up the room at minimal cost.

Almak devices are one of the most popular Russian manufacturers, the quality of which is easy to verify thanks to positive reviews.

Watch the video in which the specialist demonstrates the installation features of the Almak infrared heater:

How and where are Almak IR panels installed

Almak panels are designed for mounting on the ceiling, but if necessary, you can purchase wall-mounted mounting brackets with adjustable tilt angle. The minimum installation height is 2.5 m from the floor surface.

The infrared heating element is placed in an aluminum diffuser. The design provides a small heating of the case. Mounting to a wooden ceiling or wall is allowed.

Installation is quite simple:

• Installing a thermostat. The temperature sensor is installed at a distance of 25-30 cm from the floor level. Infrared radiation is perceived by the body 2-3 degrees higher than it actually is. Therefore, for comfortable heating, it will be enough to set 18-20 ° С.

Installation of the heater - do-it-yourself installation is allowed.The electrical connection must be made by a qualified electrician. The case is mounted on special brackets.

The location of the radiant panel. Correctly install the ceiling heater in the center, so you can ensure the maximum angle of scattering of IR rays.

Tips on how to install an infrared heater: preparation

Infrared heaters are mounted on a certain surface depending on the variety: on the ceiling, wall, floor. The model also determines the presence of a thermostat. It controls the room temperature. But not all models are equipped with it, so you should separately disassemble its installation.

Nuances when installing a thermostat:

1. The device is installed at a level of 1.5 m. So it is convenient to use it. For film decorative structures, a wireless device should be used. You do not need to install a thermostat in a draft, otherwise the work will be disrupted.
2. The correct installation location is near a door or window. For large rooms, you will need several thermostats. In this case, calculations of the total power should be made.

Working tools during installation will be a drill, level, screwdrivers, pliers and more. In some cases, a rigid bracket must be purchased for mounting. But it all depends on the model.