A simple but effective way to clean the ventilation grill from grease

Folk methods

Improvised tools that will no less effectively help in the fight for the cleanliness of the hood can be found in any home. Of course, it may take more time and effort to process such compounds, but their use will definitely save money, in addition, they do not contain harmful chemicals.

Among the variety of cleaning methods, the following options can be distinguished, described below.

Baking soda has long been known as a folk remedy for household pollution, especially kitchen utensils and appliances located in this room. To use it for cleaning, you will need a large container in which the processing agent will be prepared.The cooking technology is as follows: in the largest pot or bucket, ordinary water must be brought to a boil, about 250 grams of soda is added to it. After its dissolution, a mesh from the hood is lowered into the composition, which must be boiled for half an hour. To remove soot, you do not need to make any effort and rub the grate, the dirt will come off by itself. After boiling, the grate should be washed with water and, after wiping dry, installed in the hood.

• Vinegar is an acid, and it is usually distinguished by its ability to dissolve fats. But, in addition to this feature, vinegar can harm the skin, as well as burn the nasal mucosa. Therefore, work with vinegar should be done with gloves and a mask. The process of cleaning the parts of the ventilation device consists in treating the removable parts with acid, after 15-20 minutes the fat will completely dissolve, and the most stuck-on residues on the elements can be additionally removed with a kitchen sponge. After that, the grate or any other part should be washed with water and allowed to dry.
• Another type of acid that is used to remove contaminants is citric acid. It can be used in powder form or fresh lemon juice can be taken. Fresh fruit is cut and rubbed on contaminated areas. Citric acid in the form of granules needs to be pre-dissolved in water. The parts are treated with the resulting solution, left for some time to form a reaction, after which they are rinsed with water and installed in the hood.

• To remove fat, you can use laundry soap.They can work in two ways: in the first case, it is necessary to dissolve a bar of soap in warm water and immerse dirty parts there, another cleaning method is when the grate itself is rubbed with a bar of soap. After that, water is poured into the baking sheet from the oven, the grid is immersed there and sent to the preheated oven. The boiling process will take about 30 minutes. After that, the parts must be rinsed with water.
• Such a tool as ammonia has a rather unpleasant odor, however, as practice shows, it perfectly cleans grease traps from kitchen hoods. You need to work with him in a well-ventilated area in a respirator. A solution based on ammonia is prepared according to the following recipe: 100-150 ml must be diluted in 3-4 liters of warm water. Parts are immersed in the resulting composition for 2-3 hours, after which they are rinsed and wiped dry.

The outer surface of the cooker hood must be regularly cleaned of accumulated dirt. To do this, any selected agent is applied to the base, which needs to be given some time to combat scale and grease. After dissolution of contaminants, the composition, together with dirt inclusions, is removed from the surface with a damp rag or sponge.

Lemon juice

Lemon juice will help to quickly deal with pollution if the fat and soot on the hood are quite fresh.

Cleaning steps:

1. Cut the lemon in half. To clean the filter and grate, you can dissolve the juice of two lemon halves in a glass of water.
2. Wipe the hood grate with half of the fruit. Or moisten a rag or sponge with the prepared lemon juice solution and rub the filter.
3. Leave for 10 minutes.
4. Use a brush to remove any remaining dirt from the surface to be cleaned.
5. Rinse the parts with a clean, damp cloth.

If after this the contamination is not completely removed, then the procedure can be repeated.

Signs of an urgent need for cleaning

The reasons for poor ventilation listed above indicate one thing - the system needs constant monitoring and periodic cleaning.

You can understand that the ventilation duct needs to be cleaned by the following signs:

• dust, cobwebs have formed near the exhaust opening, debris has accumulated;
• the ventilation grille was covered with black deposits, soot and grease;
• in the summer, the apartment began to heat up very quickly;
• after wet cleaning, dust reappears after a short period of time;
• the drafts that arise in the apartment when the front door is opened have become much weaker than before.

To finally make sure that the ventilation needs to be cleaned, you can additionally check each vent. It is quite easy to do this with the help of improvised means. When checking the draft, it is necessary that at least one of the windows in the apartment is open.

Such a grill clearly indicates that the ventilation in the apartment practically does not work, and the exhaust hole requires urgent cleaning.

Homemade ways to test functionality ventilation ducts:

1. Hold a burning candle, lighter, or lit match near the ventilation grille. If there is good draft in the channel, the flame will be directed towards the hood. A fire that burns evenly indicates a lack of ventilation.
2. Take a sheet of paper or a piece of newspaper and attach it to the hole. During normal operation of the ventilation system, the paper is attracted to the grate and does not fall.

If it turns out that the ventilation does not function at all or works extremely poorly, it is necessary to clean it. Cleaning of ventilation ducts in an apartment building is carried out by specialized services. In their arsenal there is equipment for checking and cleaning ventilation ducts.

But if the need arises, each tenant of the house can clean his section of the duct on his own.

When checking the draft with an open flame, you need to be extremely careful not to accidentally set fire to the cobwebs and accumulated debris inside the vent. This is especially true for residents of gasified houses, where a fire may occur due to a gas leak in one of the apartments in the entrance

How to wash the hood from fat from the outside: rules for caring for the body

In addition to wiping it regularly (about once a week, or along with how many times you dust the house), there are some tips to keep in mind that will help keep the kitchen appliance working and looking attractive for much longer. Consider the advice of experts:

1. Do not use harsh chemicals on the cooker hood. For example, if your appliance's casing is enameled or stainless, it may oxidize, causing corrosion.
2. You should not leave the hood wet after wiping, since when it is connected to electricity, a current breakdown is possible, this is very unsafe.
3. If some parts of the case (buttons, levers and switches) cannot be removed, they should be wiped with a soft cloth dampened with a detergent solution. Never use knives, metal brushes or other sharp objects.This will cause damage to the hull structure.
4. Be sure to dust off the hood on the outside and on the air duct. This will save the appliance from unnecessary accumulation of dirt (unhygienic for the kitchen) and prevent short circuits (which simple dust so often causes).
5. If you are worried about the integrity and attractive appearance of your hood, study the instructions on how it can be processed. Otherwise, use microfiber washed in laundry soap.

It is better to process the hood motor by a specialist, however, you can clean it mechanically on your own and finally wipe all parts with medical alcohol. Dear readers of our resource, we are waiting for your feedback and comments on the topic of this article. We are always happy to receive feedback and are ready to discuss your questions.

How often should a kitchen hood be cleaned?

The frequency of cleaning the kitchen hood depends on the frequency of cooking. With regular cooking, you will have to wash and clean the structure above the stove once every three months. If you cook infrequently, then the frequency of cleansing can be reduced to 1 every six months or even a year.

Provided regular cleansing of fat, the cleaning process will not take much time. If you know some tricks or use special detergents, then even old-fashioned fatty deposits will be easy to remove.

Ready-made products for cleaning the hood from grease

Now let's figure out how to wash the hood in the kitchen. The easiest way to do this is with ready-made tools:

1. Soda is in every home. Prepare a soda solution - take a glass of soda for 2 liters of water. Pour the solution into a container of a suitable size to fit the parts of the hood.After boiling the solution, soak the contaminated elements in it for half an hour. After that, the fat will easily go away.
2. You can rub the fatty coating on the body with lemon juice or a solution of citric acid. After 20 minutes, the surface is rinsed with water. If necessary, parts can be soaked in a solution of citric acid (4 tablespoons per 1 liter of water).
3. Laundry soap removes many impurities. It is enough to grate a small bar of soap and dissolve the shavings in hot water. The parts of the hood are kept in the resulting solution for 20 minutes. Then they are well rubbed with a sponge or brush.
4. Acetic essence dissolves greasy deposits and adhering dust. It is enough to moisten a cloth in the essence and wipe the surface. After a quarter of an hour, the parts are rinsed with water. To soak the filters, you can prepare an vinegar solution. To do this, the essence is mixed with water in a ratio of 1 to 2. The filter is soaked for 20 minutes, and then washed.
5. To clean the hood, you can use a regular kitchen dishwashing detergent. It dissolves fat well. The surface can be washed with a sponge soaked in the product, or the parts can be soaked in a solution with the addition of dishwashing gel.
6. Compositions for cleaning stoves and ovens are also suitable for this purpose. Place the filter on a flat surface, such as a baking sheet, and then apply the cleaning agent to it with a sponge. After half an hour, the part is intensively rubbed with a stiff brush and rinsed with warm water.
7. Gel-like pipe cleaner "Mole" is used if no other compounds and cleaning methods help. The gel is applied to contaminated surfaces and left to act for 30 minutes. When the gel begins to act, fat deposits will foam.After that, the part does not even have to be rubbed with a brush, it is enough to rinse well under running water.
8. The kitchen appliance can be washed with ordinary bleach. Apply the solution with a brush and leave to act for 10 minutes, then rinse well with water.

If everything is already tired and you don’t know what else to play, then you can try downloading 1xBet slot machines and enjoy new experiences with the popular bookmaker.

You can also use a steam generator to dissolve fat. After that, the fatty deposit is easily washed off by any of the above means.

Folk methods for cleaning fat

If you do not know how to wash the mesh from the hood in the kitchen, then you can prepare an effective fat-dissolving agent at home. To prepare it, you will need citric acid, soda, ammonia, salt, vinegar, alcohol and laundry soap.

We prepare the tool as follows:

• we collect cold water in a five-liter pan;
• three on a coarse grater half a piece of laundry soap and throw into the water;
• then pour in half a bottle of ammonia, hydrogen peroxide or silicate glue;
• then add 1-2 tablespoons of citric acid, salt or soda ash;
• at the end, you can add half a tablespoon of alcohol or vinegar.

After dissolving all the ingredients, put the filter or other parts that need to be washed in the pan. We wait 15-20 minutes for the fat to dissolve well, remove the grate and rinse it under running water. During washing, the surface can be rubbed with a brush or sponge.

Overview of effective products for cleaning grease hoods

The outer casing, exhaust fan and some internal parts can be cleaned and dusted with water and detergent, a soft cloth or sponge. The grid is subject to deep cleaning. To achieve the effect, use folk methods or household chemicals designed to dissolve stickiness and dirt.

Folk remedies

Various acids and alkalis have high properties, but they must be used carefully, according to the recipe.

Cut the lemon into large slices or circles. Wipe the kitchen grate with the pulp, leave for 20 minutes. Then gently brush off the dirt. To enhance the effect, lemon can be sprinkled with salt. If there is no citrus, use another improvised remedy - citric acid. Crystals in the amount of 40 gr. must be dissolved in warm water, applied to the surface for 30 minutes. Rinse with a cloth.
Laundry soap with an alkali percentage of 72% will help remove old fat. You will need a brush with plastic or metal bristles. Recipe: Dissolve half a piece in a 3 liter container of water. Place the mesh in the solution, do not remove it for 20-30 minutes. After the time has elapsed, clean the hood in the kitchen with a brush. Rinse with warm water, dry.
Labor-intensive blockages can be boiled out. The method is suitable for grate and filter (charcoal varieties cannot be wetted). Place the item in a heat-resistant bowl or bucket, fill with water and laundry soap shavings

Boil until all the dirt is removed and the water turns dark.
Vinegar is a reliable home remedy, but use it carefully.Be sure to open the window in the kitchen, wear rubber gloves

Undiluted 9% acid is applied to the grate using a sponge or spray gun. After 10-20 minutes, wipe off the residue with the abrasive side of the sponge.
Pour warm water into a 5-liter saucepan, add laundry soap, ground into shavings, soda ash 5 tbsp. l, grated or chopped apple with a knife. Bring the solution to a boil, place a grate in it. It is possible in this way to clean soot, soot, fat on a baking sheet from a gas, electric oven. After 30 minutes of boiling, the parts are removed and dried.
Pepsi and Coca-Cola have amazing properties. Life hack: dip a dirty mesh in a drink for an hour and rub it with a sponge. Rinse under running water.

Household chemicals

The stores offer a selection of chemicals to combat fat deposits in the hood in the kitchen. They speed up the process of putting the device in order, preserve its appearance. Be sure to read the instructions before using. All actions should be carried out with waterproof gloves.

• Sanita. Active spray under the name 1 minute before the eyes dissolves the fatty film, removes any impurities. The express tool is universal, it can be used to clean various household appliances, including a grill and an oven.
• Shumanit. Refers to the products of the professional line. It is used for washing surfaces involved in cooking. When using, safety precautions are required. The effect appears a few minutes after distribution. Able to remove old fat.
• Cilit Bang. The manufacturer offers drugs marked AntiFat + Radiance. They easily remove dirt and gently affect metal elements.
• Synergistic.Gel for plates. Natural, safe. You can use a cleaner for hoods, ovens. Does not contain abrasive particles.
• Anti-Fat from Cinderella. An effective and affordable product that can remove any difficult stains from different types of surfaces in the kitchen and in the bathroom.

Some housewives take risks and use Mole from pipe blockages, it can damage the metal from above, cause corrosion inside.

Before using household chemicals in the kitchen, test: apply a small amount to an inconspicuous area of ​​\u200b\u200bthe appliance and study the reaction for half an hour.

The pyramid above the stove helps keep the air clean while cooking. Like a magnet attracts smoke and fumes. Active operation leads to the formation of fatty deposits. Every housewife should know how to clean the grate, wash kitchen hood filter soot and fat. The atmosphere in the kitchen and the health of the household depend on their freshness. Inhalation of soot negatively affects the state of the respiratory tract, the smell eats into the headset and interior items.

Article checked by the editors

2 How to clean fresh dirt on the filter

If the hood has been used for 1-2 months, you can try to clean its filter with dishwashing detergent. First, prepare the same detergent solution as for the surface of the appliance. It is poured into a baking sheet and the contaminated filter is immersed in the liquid. After 1-2 hours, the mesh is removed and cleaned with a stiff brush. The remaining layers of fat are poured over with boiling water and rubbed again with a brush. If it was not possible to completely clean the grid, the procedure is repeated.

You can wash the grease trap with a mixture of vegetable oil and baking soda. 3 tbsp baking soda is mixed with 2 tbsp.vegetable oil. The consistency of the mixture should resemble thick sour cream. It is applied to the contaminated surface and left to dry completely. Then clean the mesh with a dry brush. Soda is removed along with fat.

Remove dirt composition of citric acid and baking soda. First, a detergent solution is sprayed onto the surface, then a mixture of 1 tsp is prepared separately. baking soda and 1 tsp. citric acid. After adding 1 tsp. abundant foam will appear. It is applied with a sponge on a contaminated mesh and left to act.

You can prepare the cleaning composition directly on the wire rack. Powders of soda and acid are poured onto it, then water is poured (or sprayed). During the chemical reaction of acid and soda, the fat will break down and separate from the metal. After half an hour, the composition is washed off with running water.

You can clean the filter with table vinegar (9%). It is diluted with water in a ratio of 1: 1 and applied to contaminated surfaces. After 5 minutes, the vinegar solution is cleaned with a sponge along with the fat. If the layer of dirt is too large and did not come off the first time, undiluted vinegar can be applied. It is washed off with a damp sponge after 10 minutes.

You can use lemon instead of vinegar. The fruit is cut in half and the surface is wiped with a cut. After 5-10 minutes, the juice is washed off along with the dirt. Lemon juice will replace citric acid powder. 1/2 tsp powder is mixed with 1 tbsp. water and apply the mixture to the grid.

Boiling

Boiling is a fairly effective way to remove even old accumulations of fat from the filter surface of your hood.

To perform this simple procedure, you will need a large pan that can accommodate the entire grate or at least half of it.

• Initially, we prepare a solution based on salt, soda and laundry soap.
• To do this: grate about half of the bar, add a glass of salt and 2-3 tablespoons of soda, stir it all well until completely dissolved.
• The water level in the tank must be such as to completely cover the filter (or simply the maximum allowable).
• The duration of boiling is on average 7-10 minutes.
• If your grate does not completely fit in the pan, then it must be turned to the other side and continue boiling for another 5-10 minutes.
• If there are old, old spots of fat on the grate, then leave it in this hot solution for another couple of hours (turn off the burner).
• After the specified time, we clean the grate from the remnants of fat with a sponge or brush.

It remains only to rinse well under running water and admire the brilliant result of your work.

Be prepared for the fact that after “cooking” a dirty filter, a nasty and greasy solution forms in the pan.

Cleaning the hood with a steam cleaner

The easiest way to clean the grate is to use a steam generator.

• This unit will help you quickly clean almost any surface without using chemicals. In addition, it has a disinfecting effect, its temperature exceeds 150 degrees, which allows you to destroy many types of microbes.
• However, some housewives consider the steam generator too expensive. This is not entirely true, since this unit can be used not only in the kitchen, but also for cleaning plumbing in your apartment.It eliminates the need to purchase expensive cleaning products, and in the end it fully pays for the costs.

Those who do not yet plan such a purchase can use cleaning chemicals or folk remedies. And owners of dishwashers can easily cope with the problem of fat with the help of this unit.

Kitchen hood

A kitchen hood is one of the types of cleaning equipment that requires careful maintenance. Untimely cleaning leads to the fact that the performance of the product decreases, as a result, soot begins to accumulate in the kitchen and unpleasant odors reign. Understanding that the kitchen hood grate needs cleaning is very simple.

It is enough to pay attention to the fact that unpleasant odors are observed in the room when the unit is turned on, and the hood itself is very noisy

Training

Preparation is an important step that allows you to ensure proper subsequent cleaning. So, first you need to follow these steps:

Find the instructions for the unit and carefully study it.

It probably has the manufacturer's recommendations for cleaning.
Pay attention to the unit diagram. It has non-separable and collapsible elements

Only the last ones can be cleaned.
Disconnect the product from the mains.
Dismantle and disassemble it, adhering to the information in the technical description.

If the instructions are lost, you should follow these tips for disassembling the structure:

• remove the upper body element;
• remove the grid that covers all the "insides" of the system;
• remove the retainer and small elements (they must be soaked in soapy water if there is a coating of fat);
• remove the filter;
• unscrew the pipe that provides the outlet of dirty air to a special hatch.

Now that the hood is disassembled, you can start cleaning it.

Popular methods

Demanded methods of cleaning have already proven their effectiveness. Most often, the hood needs to be cleaned of a thick layer of fat, which is not easy to do. Suitable tools and instructions for their use, which are described in the table below.

Any person can clean the grate of the hood. There is nothing difficult in this. It is enough to choose the preferred cleaning method and suitable products. It is best to perform the procedure regularly to avoid premature breakdowns.

Where to begin? From inspection!

In the entire hood cleaning process, the most difficult task is cleaning the filter. This is difficult, but necessary, because if you do not perform this procedure, then the hood ceases to function normally. This is due to the fact that when clogged, the filters begin to pass less air through their nozzles, as a result of which the circulation of air flows decreases. The filter most often has a rounded shape, which makes it easier to clean. In hoods that were made a long time ago, filters of other shapes: rectangular or cassette type. Washing such filters is another task. You should start by removing the filter and visually assessing the degree of contamination. Of course, if you installed the hood the other day, then there is no point in inspecting the filter, if it is a little dusty, then you need to rinse it in hot water with detergent.

Conclusions and useful video on the topic

How to independently check the operation of ventilation in the apartment, you can learn from the video plot:

What to do if home ventilation does not work well, restoring the exhaust duct:

How is professional cleaning of ventilation shafts in apartment buildings:

Ventilation plays a leading role in ensuring safe living in an apartment. A careless attitude to this system and neglect of the rules of care can lead to health problems, and for residents of gasified houses, it can turn into even more serious consequences.

Therefore, it is necessary to monitor the state of ventilation and, if necessary, contact specialized services.

If you have experience in cleaning the ventilation duct of an apartment, please share the information with our readers. Leave and ask questions on the topic in the form below.