How to clear a blockage in the toilet: a comparison of the best methods and equipment

Cleaning with improvised means

Evgeny Filimonov

Ask a Question

If the apartment does not have special chemicals or devices that will help to cope with the trouble, you can use what is always at hand - boiling water, soda and vinegar.

To clean the drain with boiling water, you need to take a large pot of water, boil it and immediately pour it into the bowl. The jet must enter the pipe at a strictly right angle, and it must be poured quickly so that the pressure in the system increases. If the procedure immediately gave a result (the wastewater gradually leaves), you can add another bucket of boiling water.

Second method

It consists in the use of vinegar in combination with baking soda or caustic soda.

The algorithm of actions is as follows:

• pour soda powder into the toilet drain (about 150 g or five tablespoons);
• pour in the same liter of table vinegar or 120 ml of essence; wait for a reaction - when the substances come into contact, a characteristic hiss and light smoke will appear;
• after the reaction is over, pour a bucket of boiling water into the pipe.

The advantages of using home remedies are simplicity and relative safety (when working with boiling water and vinegar essence, elementary care should be taken to avoid burns). The disadvantage is low efficiency, so they can only be used to remove light blockages or soften plugs in order to subsequently remove them mechanically.

If you regularly clean the sewer pipes with baking soda and vinegar, blockages will form less often, and there will be no unpleasant smell in the toilet.

Causes of clogged toilet

Blockage in the toilet

As practice shows, people often use the toilet for other than its intended purpose, as a result of which food residues, various kinds of garbage and much more get into the sewer, which does not dissolve in water and leads to the formation of a kind of plug.This blockage often accumulates in sewer bends, making it harder and harder for drain water to pass through. Because of this, a sewer smell begins to appear in the room, and the water in the toilet bowl comes off with difficulty or even stands still.

With the manifestation of such signs, people very often ask themselves the question: how to clean the blockage in the toilet? If you decide to solve this problem yourself, you should first determine the location of the cork. It can form in your sewer, or it can be located in a common riser. This must be done because the blockage in your toilet can be removed by yourself, while the blockage in the common riser can only be removed by calling a plumber.

Very often, the cause of clogging can be improper installation of the toilet, which leads to some skew, which makes it difficult for water to pass. In this case, it is necessary to dismantle the toilet bowl and re-install it in compliance with all necessary requirements.

Clearing a clog in a toilet with a plunger

To clear a clogged toilet, the first thing to start with is to try to push through the clog with a plunger. The toilet plunger has a slightly different shape than a conventional plunger. This is the same suction cup, only with a continuation in the form of a piston (cylinder) at the end.

In principle, you can use a conventional plunger, the diameter of which is slightly larger than the diameter of the toilet drain.

Working with this tool is unpretentious - we take a plunger and with sharp jerks into the drain hole (water hammer effect) we try to push the object that caused the blockage further into the main sewer pipeline.

How to clean a clogged toilet at home - quickly and effectively

Everyone should be able to use the toilet correctly. Tell your children the basic rules for using the toilet, because in the end they can clog it. Also, a clogged toilet occurs due to a number of reasons, and not every owner knows how to properly clean it. Today we will analyze - how to properly clean the clogged toilet at home.

Causes of clogged toilet

• One of the main causes of blockages is getting into the toilet in large quantities of toilet paper, various items or hygiene products.
• There are no valves or a drain pipe installed, the task of which is to equalize the pressure in the drain or pipe.
• The toilet was not installed according to the instructions.
• Poor toilet design.

How to deal with a clogged toilet

1. Ask your family if any of your items are missing. A dropped toy or a box of cosmetics may well be blocking the drain in the toilet, and if so, then a special cable is indispensable. But if nothing is missing, then most likely you are dealing with a blockage.

2. Lay some dirty towels or even an old blanket on the floor - no matter how careful you are, some of the dirty water will still end up on the floor.

3. Scoop out the water from the toilet into a bucket prepared in advance, but not all. Leave some water to cover the plunger lowered into the toilet.

4. Lower the plunger into the toilet and start pumping the drain hole, gradually increasing the pressure, 10-15 times

Be aware that rough, careless rocking can damage the toilet. If the drain hole is not too narrow, gradually increasing water pressure will likely clear the blockage.

6. A special cable for the toilet bowl will help to complete the solution to the clogging problem.It looks like a regular plumbing cable, but is covered with plastic to protect the toilet from scratches and damage. If toys, tubes of lipstick, or just a heavy clog got into the toilet, it is highly likely that a cable will be required.

7. When you think the blockage is gone, drain the water

Take precautions: remove the lid from the toilet tank and be ready to stop the flush at any time by lifting the plastic bottle up

Other ways to clean the toilet

Hot water

If there are no special tools at hand, then you can use ordinary hot water. Take one bucket of water and bring the water to a boil. Next, you need to pour water very quickly into the toilet at a right angle. In this way you will create pressure and there is a chance that small blockages will be cleared.

Take half of the soda from a regular pack and pour it all into the toilet. Under the influence of a slit, the blockage will begin to dissolve.

Chemicals

Such products can be bought at almost any household chemical store. Chemicals most often perform a huge number of functions:

• Purify;
• Disinfect;
• Eliminate unpleasant odors;
• Have a preventive effect;
• Maintain pipes in good condition.

Plastic bottle

Take a plastic bottle, the volume of which should be 1.5-2 liters. Then you need to cut off the bottom, and twist the neck tightly. Next, cut the bottle down into the drain hole and do the same movements when you work with the plunger.

Rubber hose

You need to attach one end of the hose to a hot water faucet, and lower the other end to the very bottom of the toilet. Next, you need to run hot water with a sufficiently strong pressure. You can also use chemicals together to increase the effect.

How to clean a blockage in the bathroom

Not only the sewerage system is clogged, but also the pipes in the bathroom. If this happens, then there is no need to panic. We offer you several ways to solve this problem:

Method number 1. Using a plumbing cable. We push it into the drain hole by rotating the handle. Then we perform several pushes. We turn on the water and carefully observe it. Is the water slowly disappearing? This means that everything is done correctly.

Method number 2. Siphon cleaning. This option is suitable for those who have a bath on legs. We start by unscrewing the siphon from the drain hole and pipe. For convenience, you need to put a basin under it. We remove all accumulated debris from the tube, and then install it in place.

Method number 3. The use of special tools. Not bad have proven themselves "Tiret", "Tofix" and "Domestos".

Now you know what to do with a blockage in the toilet. All the methods proposed in the article are simple and accessible to most Russians. You can do without a plumber.

Features of cleaning the toilet with a cable

The main feature that is important to pay attention to is the type of fixture. Plumbing cables that can be used to clean the toilet are divided into 3 types:

• cable;
• spring;
• springy.

Rope tools are used to clear operational blockages. The length of such a device does not exceed 6 m, and the diameter is 6 mm. For efficient operation, the tip is made in the form of a bundle of wire. They are easy to pull out hairballs.

Rope device with a diameter of 13 mm

Spring-wound devices are thicker and more elastic, their diameter is from 9 mm.The device is equipped with a handle that allows you to rotate the device inside the pipe in any direction. At the end, the device is crimped with a bent tip. Such a device can clean mechanical blockage.

Spring-wound device with tip

Spring fixtures are classified as professional tools. They reach a length of 15 to 16 m. Diameter - 12-16 mm. Thinner devices are used to clear operational blockages, while thick and dense products do a good job of blocking pipes formed in pipes between floors.

Spring attachment 14 mm diameter

To increase the efficiency of the device, additional nozzles can be attached to the tips. To determine which element needs to be installed, you need to know the peculiarity of the sewer structure and the type of pipes.

Cleaning with chemicals

Special household chemicals are also very popular, helping to effectively eliminate the blockage that has appeared. Usually this includes acidic or alkaline liquids, products in the form of powder, granules and even sprays. Such a tool must be poured into the toilet and left for the time indicated on the package. After a certain time, it is recommended to pour hot water into the sanitary ware to clean the pipe walls from dirt and the active chemical.

The modern chemical industry also produces various means for carrying out preventive work aimed at reducing the occurrence of blockages in the future. The constant use of such products will keep the general condition of the pipes under control and ensure a long service life with appropriate handling.

Causes of blockages

The presence of curved pipes makes the toilet vulnerable to clogging, no matter how carefully and carefully it is operated. But it has been noticed that more often the owners of old faience structures with cast-iron pipes still face problems.

Over time, they are covered from the inside with various salt deposits and prevent the passage of the water flow. Chemicals that can be purchased at any supermarket or hardware store do a good job with such organic deposits.

Cleaning agent for clogs in sinks, bathtubs, toilet bowls

The second reason is the ingress of foreign objects: small children's toys, felt-tip pens and colored pencils, paper, food waste - whatever. And chemistry is unlikely to help here, you will have to use mechanical tools, for example, a plunger. But he will not be able to remove larger items such as a floor cloth, he will need a special plumbing cable.

If a cat lives in the apartment and you use litter for the tray, carefully read the disposal rules. The fact is that mineral, clumping and absorbent fillers are made from clay. Getting into the sewer, under the influence of water, the clay tightly cements the duct, and only a professional can remove the concrete plug.

The second proven method

This is the most convenient option. You do not have to mix the ingredients in a separate container beforehand.

By following simple rules and following the instructions, you will quickly get rid of the cork:

1. Half a pack of regular baking soda should be poured down the toilet.
2. We take a bottle of concentrated vinegar and pour it there.
3. It is necessary to close the drain hole and wait about two hours.
4. After a certain amount of time, hot water should be poured into the plumbing fixture, and wait again.

After completing this procedure, the resulting debris and dirt should be gone.

Vinegar should be used with caution

How to clean a clogged toilet at home - quickly and effectively

Everyone should be able to use the toilet correctly. Tell your children the basic rules for using the toilet, because in the end they can clog it. Also, a clogged toilet occurs due to a number of reasons, and not every owner knows how to properly clean it. Today we will analyze - how to properly clean the clogged toilet at home.

Causes of clogged toilet

• One of the main causes of blockages is getting into the toilet in large quantities of toilet paper, various items or hygiene products.
• There are no valves or a drain pipe installed, the task of which is to equalize the pressure in the drain or pipe.
• The toilet was not installed according to the instructions.
• Poor toilet design.

How to deal with a clogged toilet

1. Ask your family if any of your items are missing. A dropped toy or a box of cosmetics may well be blocking the drain in the toilet, and if so, then a special cable is indispensable. But if nothing is missing, then most likely you are dealing with a blockage.

2. Lay some dirty towels or even an old blanket on the floor - no matter how careful you are, some of the dirty water will still end up on the floor.

3. Scoop out the water from the toilet into a bucket prepared in advance, but not all. Leave some water to cover the plunger lowered into the toilet.

4. Lower the plunger into the toilet and start pumping the drain hole, gradually increasing the pressure, 10-15 times

Be aware that rough, careless rocking can damage the toilet. If the drain hole is not too narrow, gradually increasing water pressure will likely clear the blockage.

6. A special cable for the toilet bowl will help to complete the solution to the clogging problem. It looks like a regular plumbing cable, but is covered with plastic to protect the toilet from scratches and damage. If toys, tubes of lipstick, or just a heavy clog got into the toilet, it is highly likely that a cable will be required.

7. When you think the blockage is gone, drain the water

Take precautions: remove the lid from the toilet tank and be ready to stop the flush at any time by lifting the plastic bottle up

Other ways to clean the toilet

Hot water

If there are no special tools at hand, then you can use ordinary hot water. Take one bucket of water and bring the water to a boil. Next, you need to pour water very quickly into the toilet at a right angle. In this way you will create pressure and there is a chance that small blockages will be cleared.

Take half of the soda from a regular pack and pour it all into the toilet. Under the influence of a slit, the blockage will begin to dissolve.

Chemicals

Such products can be bought at almost any household chemical store. Chemicals most often perform a huge number of functions:

• Purify;
• Disinfect;
• Eliminate unpleasant odors;
• Have a preventive effect;
• Maintain pipes in good condition.

Plastic bottle

Take a plastic bottle, the volume of which should be 1.5-2 liters. Then you need to cut off the bottom, and twist the neck tightly.Next, cut the bottle down into the drain hole and do the same movements when you work with the plunger.

Rubber hose

You need to attach one end of the hose to a hot water faucet, and lower the other end to the very bottom of the toilet. Next, you need to run hot water with a sufficiently strong pressure. You can also use chemicals together to increase the effect.

Types of blockages

Before cleaning a clogged toilet bowl, you should find out the type of clogging.

The most common type of blockage is when sewage and human waste is prevented from passing through the sewer due to the blockage. In this case, only the toilet is clogged.

The second type of clogging is less common, and it is quite unpleasant. In this case, the drains do not enter the general sewer, but through the drain holes into the washbasin, bathroom, sink or other plumbing fixtures. This indicates that it is not the toilet that is clogged, but the main sewer system. This is due to the fact that the neighbors from the upper floors clog the common sewer with various debris. In this situation, utility workers should be called.

Cleaning the folk way

For a long time, many people have known a simple way to get rid of various blockages when ordinary soda was poured into the sewer system. To do this, take half a pack of soda, which is poured into the drain hole of the plumbing product. This is how an active alkaline environment is easily created, thanks to which you can quickly correct the situation and break through the resulting blockage. But in especially severe cases, this method will be ineffective.

When none of the proposed methods helps to eliminate the blockage that has appeared in the toilet, it remains only to call for help from specialists. Plumbers have special tools that break through blockages under high pressure. But in order to avoid cleaning the sanitary ware from all kinds of blockages, it is better not to drain various garbage into the drain device, but to throw it into the trash can.

Share this helpful article:

What is the best method to use?

What to do if the toilet is clogged: use chemistry or mechanical cleaning methods? The answer to this question depends on why the water does not drain or drain badly. If a foreign object has got into the toilet bowl, then it can be pushed with a cable or a plunger further into a wide sewer pipe (septic tank). If a plug has formed of hair, fat and waste or deposits on the walls of the pipe, then it do-it-yourself elimination with the help of chemistry will be effective. You can combine cleaning with the help of special tools and a cable - then the result will be clean drain walls, which will not cling to small debris.

There are also such contaminants that cannot be removed using the above means. For example, if during repairs the remains of various plaster and putty solutions were poured into the toilet, then no chemistry can cope with them. Theoretically, it exists, but in practice, what dissolves such garbage will corrode the pipes themselves. Be careful not to let foreign objects and mixtures with insoluble residues enter the toilet, do not forget about preventive cleaning of the drain, then you will not have to clean the clogged toilet in emergency mode when the water does not go away at all.

Lose weight easily (result in 25 days)

Why stubborn dieting DOES NOT BRING visible results, but only leads to frustration and depression, and how to still lose weight in order to:

Return the attention of her husband or find a new man.
Again feel the envious glances of friends and colleagues.
Believe in yourself, feel slim and desirable.
Do not be shy to go to the cinema or to a cafe with your friends.
Feel free to post photos from vacation or with children on social networks.

Burn fat in targeted areas

call plumber

In cases where there is no time and desire to clean pipes, or the blockage is very serious, which you cannot break through on your own, you can call a plumber.

It is possible to turn to a specialist for help both in case of blockages and, if necessary, to replace components, for example, a cracked siphon. If additional parts are used, they will have to be paid separately.

You can find a plumber in your city via the Internet. On average, the cost of cleaning work will cost from 700 rubles. If the problem is serious, even affecting the riser, removing the blockage will cost more.

Determining the location of the blockage

A clogged pipe is a fairly common problem that you should not panic and look for the plumber's phone number when faced with. You can often do it yourself, saving time and money.

Before cleaning pipes, it is important to understand exactly where the plug has formed. This directly affects the choice of method for solving the problem.

To determine the approximate location of the blockage, open the water and see how it will "leave":

• Water decreases very slowly - most likely, the cork is at a distance of more than a meter from the drain.With such a problem, the most optimal way would be to use a special metal cable.
• The water drops to a certain level, and then everything remains unchanged - the blockage is located in the area from the siphon to the first turn. In this case, it will be enough to use either folk methods or chemical means.
• The liquid does not go away at all - in 90% of cases, the siphon is clogged with fat deposits. The best option to deal with contamination would be manual cleaning of the pipeline.

These are the most common ways to identify the place where the problem has formed.

Most often, traffic jams occur at the first turn of the pipe, its narrowing or connection with the central riser.

Once you have figured out exactly where the blockage formed, you can begin to eliminate it.

Sewer blockages

To effectively eliminate the blockage without resorting to the help of specialists, it is necessary to navigate in problem areas. To do this, you need to understand the structure of the sewer system. Let's take a closer look:

If the kitchen sink or sink is clogged. You should not panic, but the first thing to do is look under the sink. There you will see a siphon, which has a sump in the form of a bowl, from which a pipe goes further directly to the riser. In most cases, it is the siphon that is clogged. Due to the peculiarities of its design, it performs several functions at once: it collects most of the debris and heavy particles at the bottom of the bowl and prevents the penetration of an unpleasant odor from the sewer into an apartment or house. Water, which is constantly present in the sump, locks these "aromas".You will realize that the system needs cleaning when there is so much debris in it that there is simply no room for water, and odors begin to seep out. The first step is to unwind the siphon. You should start from its bottom. Be prepared for the fact that stench will fall on you, and dirty dark water may flow. Sometimes the siphon is twisted very tightly. In order not to strip the threads and damage it, wrap it with a cloth and try again. Be sure to place a basin or bucket under the siphon to prevent dirt from getting on the floor. And don't forget to wear rubber gloves.
Remove debris from the sump. In the case of a kitchen sink, these will be large pieces of food, onion peels and other food particles. In the case of a washbasin in the bathroom - in 90% of cases it will be hair. They can be wrapped around the threaded part and can be difficult to remove. After complete removal of accumulations in the sump, it must be thoroughly rinsed with hot running water and only then screwed into place. Turn off the water and see if the water drains well. If there is a result, but it is not sufficient, it is necessary to unscrew the siphon completely. Sometimes it happens that the hair is wound on a long screw, which acts as a fastener. It should be unscrewed from above, and hold the siphon from below so that it does not scroll.

If the bathroom drain is clogged. The main cause of this type of clogging is the large amount of hair that enters the system during shampooing. You need to follow the same steps as in the previous case. The siphon must be checked first.
Less often, but it happens that the toilet drain is clogged.This can happen in the event of improper operation or if a third-party object enters the system. We have already said that with frequent and regular draining of mortar residues into the toilet, clogging is inevitable. The same will happen if you throw plastic bags, personal care products and used baby diapers down the toilet. In case of non-passage of water during flushing, it is necessary to unscrew the wide flexible corrugation, which is located behind the toilet and is connected to the riser. And with your own hands to get out of there a foreign object that interferes with the normal functioning of the system. Cement or plaster sediment should also be removed as far as possible. Again, do not forget to substitute a basin under the corrugation. The drain may not work if the corrugation is not sloped and installed almost perpendicular to the drain

Pay attention to this moment too. You can fix this problem yourself only by raising the level of the toilet bowl and arranging an impromptu podium

After all, the corrugation is inserted into an already prepared hole in the riser, which is almost impossible to remake.

Sewer cleaning chemicals

Professional plumbers do not advise cleaning blockages with chemicals, because after passing through the reaction they can form a crust (deposit), and thus only aggravate the situation. In addition, most products can only dissolve organic blockages.

But we will not throw off the chemical method of cleaning the toilet from the shields. There is a wide range of household chemicals on the market. You just need to walk to the nearest hardware store and purchase the tool you like.

There are different situations in life, what to do if there is no department of household chemicals in the store, or there is no hardware store nearby? Can be done with hand tools.

On the Internet, it is advised to clean the blockage with soda and vinegar. Yes, of course, soda and vinegar are strong substances, but when they react, they form three neutral substances: sodium acetate (CH3COONa), water (H2O), carbon dioxide (CO2).

How to be in such a case? There is a way out - to turn baking soda (NaHCO3) into sodium hydroxide (NaOH). How to do it, watch the video:

Pipe Cleaning Chemicals

There are many chemicals sold in supermarkets to deal with clogged pipes. These can be gels, powders, sprays, liquids or granules. Such chemicals can easily cope with the problem that has arisen. Among other things, chemicals perfectly disinfect plumbing, keep drain pipes in good condition, and also ensure their normal performance for a long time.

Chemicals should be used strictly according to the instructions, while observing safety precautions, using rubber gloves when working.

Formic, acetic, sulfuric or hydrochloric acid can be used as chemicals.

However, they should be handled very carefully, especially if the sewerage system is represented by old cast-iron pipes.

The best toilet bowl cleaners for rust

Rusty stains on the walls of the toilet spoil the whole look of plumbing and the toilet as a whole. The problem appears due to poor-quality water, a malfunctioning drain, and a number of other reasons. In any case, to remove rust, you need special cleaners.

Nordland Lemon - active foam for cleaning the toilet

5

★★★★★
editorial score

91%
buyers recommend this product

See review

Nordland is a foam for cleaning toilets, bidets and urinals that copes with lime and urolithiasis, rust stains and other contaminants. The unique form of the product is convenient for application - lush foam penetrates into hard-to-reach places, destroys all bacteria and microbes. The housewives note that the product perfectly removes unpleasant odors, leaving only a pleasant lemon scent after cleaning.

The hypoallergenic formula consists of natural ingredients without the addition of harsh chemicals - after use it decomposes by more than 90%. After cleaning, a protective film remains on the walls, which allows plumbing to stay clean longer, preventing the development of bacteria.

For cleaning, it is enough to apply foam for 5-10 minutes and distribute it over the entire surface, it does not require additional efforts.

Pros:

• antibacterial effect;
• biodegradable formula;
• convenient release form;
• pleasant aroma;
• does not cause allergies;
• economical consumption;
• effectively removes plaque, rust and other contaminants.

Minuses:

expensive - 300 rubles for 500 ml.

Buyers of this tool were divided into 2 camps. The former note that, having tried Nordland foam, they will no longer return to ordinary gels. Others, on the contrary, considered this format extremely inconvenient and prefer standard liquid and gel products.

Sanfor Activ "Antirust" - a fast-acting toilet bowl cleaner

4.9

★★★★★
editorial score

89%
buyers recommend this product

Sanfor Activ "Antirust" - a tool for intensive cleaning of plumbing.The composition of the product is extremely effective: it contains a complex of acids, alkalis and surfactants that cope with drips, rust, plaque and microbes. To obtain a visible effect, 1 minute is enough - the pollution dissolves literally before our eyes.

There are no chlorine-containing substances in the composition, so the smell of the product is not too caustic. This allows the cleaner to be used on stainless steel, chrome and other finicky surfaces. The liquid is sold in 750 ml bottles with a narrow spout for easy application. The lid is child-resistant and reliably prevents liquid from leaking.

Pros:

• antimicrobial action;
• dissolves plaque and rust;
• super fast effect;
• affordable price (from 70 rubles per bottle);
• child-resistant lid;
• no pungent odor.

Minuses:

• high consumption;
• hard to find for sale.

Sanfor Activ "Antirust" is not intended for regular cleaning. It is taken to clean old deposits and the most difficult contaminants. Due to its too liquid consistency, it quickly slides down the walls and the consumption is extremely uneconomical.

Domestos "Anti-rust and Anti-plaque" - the most effective gel

4.8

★★★★★
editorial score

80%
buyers recommend this product

Domestos "Anti-rust and Anti-plaque" is an acid-based gel for removing old dirt on the toilet bowl. It is recommended to use it during the general cleaning of plumbing. The thick formula allows the cleaner to contact the surface for a long time and cope with stains even under water.

To eliminate rust, the product must be left on the surface for half an hour. You don’t need to scrub the toilet with a brush, just rinse it with water - the stains will go away along with the remnants of Domestos.The gel is sold in black plastic bottles of 0.75 and 1 liter, which have the usual narrow spout for application under the rim.

Pros:

• effectively cleans stubborn dirt and plaque;
• does not require mechanical cleaning;
• works underwater;
• disinfects;
• available in most stores.

Minuses:

• cannot be kept for too long;
• not suitable for chrome parts;
• acrid smell.

If you leave Domestos for a longer period, you can ruin the surface of the toilet. Many housewives note that the bright blue dye is eaten away, and it is extremely difficult to wash it off later.

Using baking soda, vinegar and boiling water

The third method is based on the use of soda, vinegar and boiling water.

1. Flush the water out of the toilet, leaving a small amount at the drain.
2. Pour in ½ pack of soda, trying to push it deeper.
3. Pour a glass of table vinegar 9% into the drain.
4. After 20 minutes, pour boiling water into the toilet bowl or simply flush the water.

Attention! In no case do not use boiling water if your toilet is equipped with a connecting corrugation made of thin plastic. If necessary, flushing in this case, you can use hot water

I remembered how two hundred years ago they washed dishes not with fairies (which, by the way, I also tried to pour into the sink), but with soda. Was not, spread the whole pack in a ladle in three glasses of water and poured the whole mixture into the hole in the bathroom. Two minutes later, I didn’t have time to move away, I hear the sound of such a “fyrrrrrrrr”, I didn’t understand, I flushed the toilet and lo and behold!

How to clean the toilet from clogging with a cable

When using a plumbing cable when the toilet is clogged, the following instructions must be observed:

1. The floor in the toilet must be covered with a film. Protect hands with rubber gloves.The device is removed from the packaging and inspected for integrity. Determine the cause of the blockage and its location. Select suitable nozzles.
2. The cable must be put into the toilet, through the drain hole. It is not necessary to dissolve it in full length immediately. The device is untwisted gradually, overcoming difficult places and pipe bends. The rest is kept twisted into a ring, in the hand where the handle is located. To push the tool through the pipes, the handle is rotated in the desired direction and gently push the end of the device into the depth.
3. When the tip hits the garbage plug, use the handle to make a few pushes, trying to break through the blockage. So you can clean the blockage with a parting with a “harpoon” tip. If there are hooks at the end, then they need to pick up the blockage and pull it out.
4. When the stagnant water begins to decrease, the removal of the blockage can be considered complete. It remains only to check the performance of the system. When flushing, the water in the toilet should swirl into a funnel.

Comment! To soften the blockage, you can empty the tank and feed hot water from the tap into the toilet during the cleaning process.

How to clean the toilet or sink yourself (the same principle) using a cable, you can watch the video: